Honda Foreman 500 And Honda Rubicon WINCH MOUNTING KIT INSTALLATION

0

Filed Under (Honda) by admin on 13-12-2011

download
Begin by removing the front skid plate located on the front of the ATV. Remove the four side 8mm bolts and four bottom 6mm bolts securing the front skid plate, figure 1. Save the fasteners as they will be used later to reinstall the front skid plate. 2. Remove the four plastic rivets on each side of the front plastic fascia, figure 2. Use a large screw driver to carefully remove the center rivet. After removing the center rivet, remove the rivet housing. Save the fasteners as they will be used to reinstall the front plastic fascia. 3. Remove the two 6mm bolts that attach the front plastic fascia to the bumper, figure 3. Remove the front plastic fascia at this time . Remove the two 6mm bolts that attach the front bumper to the plastic headlight assembly, figure 4. Save the fasteners as they will be used to reinstall the front bumper. 5. Remove the two top 8mm bumper bolts that attach the front bumper to the front rack, figure 5. Save the fasteners as they will be used to reinstall the front bumper. Figure 5 Remove Top Bumper Bolts Remove (both sides) 6. Remove the two ottom bumper bolts that attach the bumper to the bottom of the vehicle frame, figure 6. Save the fasteners as they will be used to reinstall the front bumper

Incoming search terms:

Honda TRX 450R BoonDocker Nitrous System Installation Instructions

0

Filed Under (Honda) by admin on 12-12-2011

download
This nitrous manifold greatly simplifies the way extra fuel is delivered that is needed for nitrous use. The carburetor vents
are connected to this manifold, allowing the carburetor(s) to breathe normally through the airbox when nitrous is not used.
When nitrous is sprayed, the manifold produces a positive pressure that goes to the carburetor float bowl, which “pushes”
more fuel through the main jet of the carburetor(s). This eliminates the need for an extra fuel pump, fuel solenoid, extra
plumbing, and nozzle(s) that are necessary to inject the extra fuel in other systems.This manifold is also designed to vary the float bowl pressure in relation to nitrous pressure, thus keeping the nitrous and fuel delivery in sync. Fluctuations in bottle temperature greatly affect nitrous pressure, which affects nitrous delivery. By automatically adjusting the fuel delivery as nitrous pressure varies, this manifold makes nitrous safe, reliable, and easy to use. The valve shown in picture (A) will require both the 4an x 1/8 npt fitting and the 1/8 npt plug. The valve shown in picture (B) will only need the 4an x 1/8 npt fitting. Use thread sealant on these fittings, be sure not to get any sealant inside the valve. Remove the upper mounting bolts on the front bumper. Install bracket support strap and reinstall the mounting bolts. 2. Install rear strap mounts over frame tubes. 3. Attach saddle bracket to support brackets, front and rear using supplied hardware.

2003 – 2004 Matrix FOG LIGHT INSTALLATION PROCEDURE AND REMOVAL

0

Filed Under (Toyota Manuals) by admin on 29-10-2011

download
Check that the fog light installation parts on the front bumper are the new shape. 2. If the bumper is the previous design, cut off the part indicated in the illustration. 3. Install the fog ligh New style fog lights have been developed for the Matrix. The front bumper has been modified to accommodate this change. In order to install the new style fog lights into the old bumper design, the following procedures must be followed

2008 Matrix FRONT LICENSE PLATE MOUNTING BRACKET INSTALLATION DURING PDS

0

Filed Under (Toyota Manuals) by admin on 19-10-2011

download
Using the two self-tapping screws, install the mounting bracket to the front bumper. NOTE: Do NOT drill holes in the dimples. Tighten the driver’s side screw first and then tighten the passenger’s side screw. 3. Install the front license plate to the bracket using non-corroding self-tapping screws of the following size

TOYOTA FJ CRUISER – FRONT BUMPER INSTALLATION INSTRUCTIONS

0

Filed Under (Toyota Manuals) by admin on 23-09-2011

download
Before beginning installation, assure that vehicle has been pulled forward into work-area with the wheels straight and that the ground is level. The clearances around the FJ bumper are critical to proper installation and fitment. Moving vehicle with wheels turned causes slight frame twist preventing ease of removal of OE bumper and nstallation of new bumper without issue. Make sure you have plenty of room to work around front of vehicle. Open the hood at this time, you will need to see down through the inner-body core-support while removing your OE bumper and installing your Body Armor FJ Bumper. Step 2 a. Unpack bumper using staple puller to remove staples. Save all packing materials and take care not to tear cartons. b. Remove hardware and misc.parts. Check parts/hardware list to confirm all parts and necessary hardware are included. c. It’s a good idea to spray all OE attaching hardware at this time with penetrating oil before beginning removal of OE bumper. This will ease removal as well as to help assure that none of the bolts’ / nuts’ threads are damaged during removal. Use extra caution when working with the bumper mounting studs & nuts. Step 3 a. Begin removing OE bumper following instructions and photos on the following page for detailed descriptions and references. When done, proceed to Step 4 here.

How to Replace your starter : 99 Corolla VE

0

Filed Under (Toyota Manuals) by admin on 17-06-2011

Use a 10mm ratchet attachment to remove the battery from the vehicle. Negative terminal first, then positive. Be careful not to cause an arc between the two terminals as intense pain will result.
Remove the plastic plate that the battery sits in. 2. Using the 10mm attachment again, remove the 6 bolts that hold the passenger side front splash guard from underneath the front bumper. 3. From underneath the vehicle, locate the oil filter. Look above oil filter and you will see the starter. Locate the bottom 14 mm bolt that attaches the lower portion of the starter to the engine. The bolt drives from left to right. The starter is mounted toward the front of the vehicle and underneath the intake manifold. Still cant find it?
Follow the cable that leads from the positive battery terminal. It ends at the starter. Not sure you have the right bolt? Stick your 14mm attachment on it with your fingers and see if it fits on properly

1996 Toyota Supra STARTING & CHARGING SYSTEMS

0

Filed Under (Toyota Manuals) by admin on 16-06-2011

Download
Use a 10mm ratchet attachment to remove the battery from the vehicle. Negative terminal first, then positive. Be careful not to cause an arc between the two terminals as intense pain will result.
Remove the plastic plate that the battery sits in. 2. Using the 10mm attachment again, remove the 6 bolts that hold the passenger side front splash guard from underneath the front bumper
From underneath the vehicle, locate the oil filter. Look above oil filter and you will see the starter. Locate the bottom 14 mm bolt that attaches the lower portion of the starter to the engine. The bolt
drives from left to right. The starter is mounted toward the front of the vehicle and underneath the intake manifold. Still cant find it? Follow the cable that leads from the positive battery terminal. It
ends at the starter. Not sure you have the right bolt? Stick your 14mm attachment on it with your fingers and see if it fits on properly

HONDA VTX1300 FRONT FENDER BUMPER INSTALLATION INSTRUCTIONS

0

Filed Under (Honda) by admin on 25-12-2010

download
1. Carefully slide the bumper up into position (it will be necessary to flex the bumper inward to get the brackets over the fender mounting bolts. 2. Remove the 2 front bolts and replace them with the longer bolts supplied and next replace the 2 rear bolts. Tighten all 4 securely. 3. Install the 4 nuts supplied, before tightening peel the backing from the clear bumper supplied and stick it to the fender behind the center of the lower chrome front bumper rail, center the bumper left to right while keeping it down against the rubber bumper on the fender and tighten the 4 nuts securely.

HONDA VTX 1300 FRONT FENDER BUMPER INSTALLATION INSTRUCTIONS

0

Filed Under (Honda) by admin on 23-12-2010

download
1. Carefully slide the bumper up into position (it will be necessary to flex the bumper inward to get the brackets over the fender mounting bolts. 2. Remove the 2 front bolts and replace them with the longer bolts supplied and next replace the 2 rear bolts. Tighten all 4 securely. 3. Install the 4 nuts supplied, before tightening peel the backing from the clear bumper supplied and stick it to the fender behind the center of the lower chrome front bumper rail, center the bumper left to right while keeping it down against the rubber bumper on the fender and tighten the 4 nuts securely.

Kawasaki KVF 360 Winch Mount Installation Manual

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
1. Remove the bottom and middle bumper mounting bolts. 2. Pull the front bumper outwards while sliding the winch mount behind the bumper with the roller fairlead mount tabs facing downward and towards the front. Slide the roller fairlead mount tabs through the upper opening of the bumper. 3. Bring the back of the winch mount up to the bottom of the middle bumper mounting tubes and install the (2) 5/16″ x 1-1/8″ x 1-3/4″ u-bolts over the tubes and through the winch mount. Install (4) 5/16″ flat washers and Nylock nuts. 4. Install the (2) 5/16″ x 1-1/4″ x 2″ u-bolts over the middle bumper cross tube then through the winch mount. Install (4) 5/16″ flat washers and Nylock nuts and tighten all nuts. 5. Install the winch to the bottom of the mount using the hardware provided with the winch. Be sure the winch winds in the correct direction. 6. Install the roller fairlead using (2) 5/16″ x 3/4″ hex bolts and 5/16″ Nylock nuts provided (rollers should turn freely). Note: Bottom roller may need to be removed to run wire rope through. 7. Push the bumper back into place and reinstall the original bolts. 8. Using the instructions provided with the winch, wire accordingly

Incoming search terms:

Incoming search terms: