2006 – 2007 Harley-Davidson Softail Ultimate seats Installation Manual

0

Filed Under (Harley Davidson) by admin on 04-04-2012

download
1. Remove original seats from your bike. #2. Your new Ultimate seats install using the front seat side mount bolts and the passenger seat is bolted to the front seat and rear fender. Side mount hex nuts = 2. If your stock rider seat is a rear fender mount, install one of the hex nut inserts on each side of the frame if they are not in your bike frame already. #3. All the mounting brackets are already installed on your new seats. #4. Connect our passenger seat to the rider seat with the 2 new round head allen bolts ( 1/4″ x ¾”) #5. Use the 2 new supplied bolts to attach the rider seat to the bike frame, one on each side into the threaded inserts ( 1/4″ x ½”) pan Phillips head) #6. Use the other new bolt for the passenger seat rear bracket in the fender (1/4″ x ½”) pan head. Enjoy the ride again

Yamaha V-Star 1100 Jetting the Carburetors INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 11-03-2012

download
Remove air filter housing Remove the seat or seats Disconnect Fuel Lines (also the vapor line from tank to charcoal canister on California models) Disconnect instrument connectors from the fuel tank Remove fuel tank Remove air box Disconnect TPS and heater connectors Remove chrome carb cover Disconnect Fuel Lines Remove rubber carb elbows Disconnect throttle cables from carbs Remove the carbs Perform the jetting 1. Remove the Chrome air filter housing. To remove the chrome dog-dish (air filter housing) from the right side of the bike, you will need to remove the two mounting bolts and loosen the clamp that holds the air duct to the back of the housing. You will need a 5 mm Allen wrench and a #2 Philips screwdriver. 2. Remove the seats. This can be accomplished by using a 5 mm Allen wrench and removing the Allen head bolt from just behind the rear seat and the bolt just behind the front seat. Pulling up and back will free the seats. One smooth motion will do it. 3. Gain access to the dashboard plug and unplug it (It is white) Note: Your trip odometer will lose its count, please record the number if you wish to save your current mileage for this tank of gas. Figure A shows the three plastic rivets that need to be removed to gain access to the dashboard plug. Using your Philips head screwdriver, press the small circle in the middle of the rivets down… a click is felt. Remove the rivets by hand. You have freed the cover and you may lift it up to expose the electrical connector that needs to be unplugged. Figure B shows the plug

TOYOTA NEW SEAT BELT TONGUE PLATE STOPPER SERVICE PARTS

0

Filed Under (Toyota Manuals) by admin on 10-10-2011

download
installation procedures are provided to supplement the Repair Manual. MODEL YEAR Avalon 1995 – 2001 Camry 1983 – 2001 Corolla 1980 – 2001 Camry Solara 1999 – 2001 Sienna (Front Seat Belt Only) 1998 – 2001 RAV4 1997 – 2001 4Runner 1992 – 2001 Land Cruiser 1991 – 2001 Tundra 2000 – 2001 Tacoma 1997 – 2000 ECHO 2000 – 2001 Celica 1980 – 2001 Prius 2001 – 2001 Tercel 1981 – 1999 PREVIOUS PART NUMBERCURRENT PART NUMBER PART NAME N/A 73219-02010 Stopper, Tongue Plate (Black)* N/A 73219-02020 Stopper, Tongue Plate (Gray)* N/A 73219-02030 Stopper, Tongue Plate (Beige)* *Use a stopper color that is closest to the seat belt webbing color. OP CODE DESCRIPTION TIME OPN T1 T2 BD0047 Install Seat Belt Tongue Plate Stopper 0.1 73219-020#0 62 12 Applicable Warranty*: This repair is covered under the Toyota Comprehensive Warranty. This warranty is in effect for 36 months or 36,000 miles, whichever occurs first, from the vehicle’s in-service date. *Warranty application is limited to correction of a problem based upon a customer’s specific complaint

Incoming search terms:

2004 – 2005 Camry, Highlander, And Solara, 2005 Matrix & Corolla PASSENGER AIRBAG INDICATOR LAMP

0

Filed Under (Toyota Manuals) by admin on 10-10-2011

download
passengers weighing approximately less than 100 pounds, depending on their seating position. It is important for the front seat passengers to know that proper operation of the advanced frontal airbag system is highly dependent on the pressure placed on the seat bottom. Situations that add or subtract sensed weight can result in occupant misclassification. To minimize this situation: Check seating posture. Passengers should be seated upright with their back against the seat back and feet on the floor. Check loading conditions. Extra weight from items, such as bags or groceries or toys, hanging on the seat back can add to the sensed weight of the front seat passenger. A rear seat passenger lifting the front seat with their legs, objects placed under the front seat, or the front seatback in contact with the rear seat can subtract from the sensed weight of the front seat passenger. If the passenger airbag indicator lamp continues to switch ON to OFF after checking the above conditions, perform the following repair procedure. NOTE: The safest place for children is in the rear seat. Please note that Toyota recommends that you never install a rear-facing child restraint in the front passenger seat, even if the passenger “Airbag OFF” lamp is illuminated. Please refer to you Owner’s Manual for additional details. 2004 – 2005 model year Camry, Highlander, and Solara vehicles produced BEFORE the Production Change Effective VINs shown on the following page. 2005 model year Matrix and Corolla vehicles produced BEFORE the Production Change Effective VINs shown on the following page

Incoming search terms:

HARLEY DAVIDSON SIGNATURE SERIES SOLO SEAT KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 19-02-2011

download
REMOVAL NOTE Refer to owner’s manual or service manual for seat removal instructions for your model. 1. Remove right and left saddlebags according to the instructions in the service manual. Save saddlebag mounting brackets and hardware. 2. Remove passenger seat strap. Discard passenger seat strap. 3. Remove existing seat from vehicle. 4. See Figure 1. Remove and discard stock nuts (2) from studs (1) on rear fender (3). INSTALLATION Install Rider Seat 1. Push front seat on frame with mounting bracket at rear. 2. Firmly push front of seat downward and rearward until frame tongue engages slot in seat. 3. Push seat forward until studs are centered in slots of mounting bracket. 4. See Figure 4. Install two nuts (4) on studs to secure rear seat mounting bracket to rear fender. Alternately tighten nuts to 60-96 in-lbs (6.8-10.9 Nm). 5. If installing a new passenger seat, refer to the instructions included with the kit. After installing seat, pull upward on seat to be sure it is locked in position. While riding, a loose seat can shift causing loss of control, which could result in death or serious injury. (00070b) 6. If installing passenger seat, install passenger seat strap following the instructions in the service manual. 7. Install right and left side saddlebags following the instructions in the service manual. 1 2 3 2 1 is04121 1. Stud (2) 2. Nut (2) 3. Rear fender Figure 1. Rear Fender Install Rider Backrest NOTE Flaps shown removed for clarity of illustration. 1. See Figure 2. Turn backrest assembly (1) at a 45 degree angle clockwise to the seat. Slide the backrest shaft (2) through the flaps and into the receptacle in the seat. 2. While pushing down on the backrest assembly, twist the backrest counterclockwise until the shaft hits the stop. 3. Verify that the backrest assembly is locked in place by pulling up in the backrest pad

HARLEY DAVIDSON DYNA CUSTOM SEAT KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 15-02-2011

download
WO-UP SEAT INSTALLATION Currently Installed Seat Removal NOTE When performing the following procedures, avoid scratching painted surfaces (fender, tank, etc.) with tools or metal seat tabs. 1. Remove currently installed seat following the instructions in the Owner’s Manual. 2. If a two-up seat WAS installed: Proceed to Step 6, Grab Strap Installation . If a solo seat WAS installed: See Figure 1. Remove the Bar & Shield hole plug (11) from the rear seat mounting hole (1)Seat mounting hole, rear 2. Fender hole, center 3. Seat mounting hole, front 4. Grab strap mounting hole 5. Wire routing hole (reference) 6. Fender hole, front (reference) 7. Hardware location for two-up seat 8. Hardware location for solo seat 9. Seat retention nut 10. Retention washer 11. Hole plug, Bar & Shield 12. Hole plug, plain Figure 1. Fender Hole Identification and Hardware Locations 3. At the front seat mounting hole (3), remove the retention washer (10) from the seat retention nut (9). From the underside of the fender, remove the seat retention nut from the vehicle. Insert the Bar & Shield hole plug into the front seat mounting hole. 4. See Figure 2. Obtain the cable strap (3) from the kit. a. Place the retention nut (1) over the cable strap (3) so that the wide end of the nut rests on the eye of the cable strap. b. Thread the cable strap up under the fender and through the rearmost seat mounting hole. c. Pull up on the cable strap to hold the nut snug against the underside of the fender. d. With the rib on the retention nut seated into the notch in the fender hole, slide the retention washer (2) into place from the rear (this will lock the retention nut in place), then remove the cable strap. 3 2 1 is01955 1. Retention nut 2. Retention washer 3. Cable strap (installation aid) Figure 2. Retention Nut Installation Grab Strap Installation 5. If a two-up seat WAS installed: Remove the existing grab strap and all attaching hardware, then proceed to Step 6. If a solo seat WAS installed: Proceed to Step 6. 6. See Figure 5. Obtain the new grab strap (8), hex head screw (9), plastic retention nut (10), washer (11) and hex nut (12) from the kit. 7. From the underside of the fender, insert the screw up through the grab strap mounting hole and secure with the plastic retention nut.

Incoming search terms:

HARLEY DAVIDSON SOFTAIL REAR SADDLEBAG GUARDS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 14-02-2011

download
INSTALLATION 1. Remove saddlebag, if equipped, from motorcycle. 2. Remove passenger footpeg or passenger footboard assembly (including footboard mount) from vehicle. 3. See Figure 1. Remove nut (1), seat strap bracket (if equipped) and 3/8 inch diameter bolt (2) from indicated position on rear fender support (immediately to the rear of the front seat) Discard the bolt, but save the nut for reinstallation. This location is where the upper part of the saddlebag guard will mount. 2 1 is03883 1. Rear fender support nut 2. Rear fender support screw Figure 1. Hardware Removal 4. See Figure 2. Install saddlebag guard (4) top flange (5) against fender support (3). Install 3/8-16 x 1-3/4 inch button head bolt with the seat strap bracket (if equipped) and hardware removed in Step 3 (if equipped) and nut in same direction as bolt removed in Step 3. Finger tighten only. 5. Position bottom flange (6) of saddlebag guard (4) against inboard surface of motorcycle frame (7) at location where passenger footpeg (2) (or passenger footboard bolt) attaches. If Heritage-Style Saddlebag relocation kit, Part Number 90238-00 is to be installed, the bracket should be positioned between the saddlebag guard flange and the motorcycle frame member. Follow installation instructions included with that kit. 6. See Figure 3. Determine your model application and follow the applicable installation procedure below: On models with passenger footpeg, but without saddlebag relocation bracket: Install 3/8-16 x 2-3/4 inch socket head cap screw (6) (For 2007 FLSTC Models, use the 3.5 inch long socket head cap screw (7) from kit) through footpeg support (B). Install support to frame. Tighten support bolt to 35-45 ft-lbs (47-61 Nm). Install lower saddlebag guard flange over bolt protruding from inboard surface of frame member. Install 3/8-16 lock nut to end of bolt. Tighten to 35-45 ft-lbs (47-61 Nm). Install footpeg (C) according to Service Manual instructions. On models with passenger footpeg and saddlebag relocation bracket: Install 3/8-16 x 2-3/4 inch socket head cap screw (6) (For 2007 FLSTC Models, use the 3.5 inch long socket head cap screw (7) from kit) through footpeg support. Install support to frame. Tighten support bolt to 35-45 ft-lbs (47-61 Nm). Position saddlebag relocation

Incoming search terms:

HARLEY DAVIDSON SOFTAIL SEAT KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 13-02-2011

download
INSTALLATION FXST, FXSTS, and FXSTB models NOTE When performing the following installation procedures, avoid scratching painted surfaces (fender, tank, etc.) with tools or metal seat tabs. 1. Remove existing seat from motorcycle by unscrewing seat at rear bracket and unhooking front seat tab. 2. See Figure 4. Remove and discard existing grabstrap and save fastening hardware from the motorcycle. 3. See Figure 4. Install the grabstrap (7) from kit with the hardware saved in Step 2. Install the grabstrap according to Figure 1. Kit Number: 51470-06A, 51397-06A Grabstrap Number: 51184-00 Kit Number: 51468-06A, 51469-06A, and 51801-07 Grabstrap Number: 51176-96B is00420 Figure 1. Grabstrap installment information 4. See Figure 4. Slide the back of the seat through grabstrap and hook front tab of seat (1) into frame. Secure seat bracket to fender with screw (8). After installing seat, pull upward on seat to be sure it is locked in position. While riding, a loose seat can shift causing loss of control, which could result in death or serious injury. (00070b) 2007 and later FXSTC models NOTE Refer to the Owner’s, or Service Manual instructions for removal of the stock seat, and mounting hardware. 1. Remove, and discard the existing grabstrap, and mounting hardware. 2. Remove, and discard the plug in the rear mounting position on the fender. 3. See Figure 2. Using the retaining nut (1), washer (2), and cable strap from the kit; Install the nut, and washer in the rear hole location on the fender (Note: A cable strap can be used as an installation aid)

HARLEY DAVIDSON BADLANDER XL CUSTOM SEAT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 03-02-2011

download
Removal of Stock Seat 1. Remove screw (8) to detach rear seat mounting bracket from fender. 2. Slide seat rearward to unhook front of seat from frame, then remove seat. 3. If equipped with a grab strap, remove hardware that holds it in place and remove strap. Installation of Kit Seat For 1996 and earlier models: Make certain you select the correct kit screw in step 1. Attempting to install a coarse threaded screw in a fine threaded hole, or vice versa, will damage threads. 1. Secure grab strap (2) to fender using washer (7) and appropriate screw (6) below: On 1995 and earlier models use 1/4-28 (fine) screw. On 1996 – 2003 models use 1/4-20 (coarse) screw. 2. Slide seat into position until front of seat engages frame, then secure bracket to fender with screw (8) using guide washer (3) between bracket and fender with the small washer diameter facing upwards. The guide washer will center the screw in the bracket hole and serve as a washer to protect the fender. NOTE For 1997 883 models, a retention nut and washer must be installed into the fender hole, covered with a plastic cap, where the rear seat bracket will be attached. A cable strap is included to aid in this installation. For 1997 – 2003 models: 1. Install grab strap (see step 1 for 1996 and earlier models). 2. Remove plastic cap from hole in fender where the rear seat bracket will be attached. 3. Place retention nut (5) over cable strap (9) so wide end of nut rests on eye of cable strap. Thread cable strap up under fender and through fender hole. Pull up on cable strap to hold nut snug against underside of fender. 4. With rib on retention nut seated into notch in fender hole, slide retention washer (4) into place from the rear. This will lock the retention nut in place. 5. Slide seat into position untilang=en

HONDA VTX 1800R AND VTX 1300R SOLO RACK INSTALLATION INSTRUCTIONS

0

Filed Under (Honda) by admin on 21-12-2010

download
1. Remove the stock passenger seat. And “U” shaped mounting bracket from the rear fender. 2. Install the 2 “L” brackets provided (NOTE: there is a left and a right) onto the rear fender using the bolts from the stock bracket. Snug the bolts just enough to still allow them to slide. 3. Using the 3 knobs provided re-install the stock seat using the knob with the long stud in the rear hole. Center the slot in the seat and tighten the knob. Install the 2 knobs with the short threaded studs through the front seat mounting holes and into the new brackets. Center the bracket holes to the seat holes and snug the knobs. This will align the forward brackets. Carefully remove all three knobs and the seat. Tighten the forward bracket securely. 4. Install the solo rack starting with the 2 short knobs at the front then the long knob at the rear with the black spacer between the rack and the fender. Tighten all 3 knobs securely, as tight as you can by hand. Lost knobs are not a warrantable item. Now you can switch from your new cool solo rack look back to your stock passenger seat in seconds without any tools. NOTE: when using the stock seat, place the black spacer on the long rear knob and install them over the stock rear seat bracket. This keeps the long stud from extending below the inside of the fender and possibly contacting the rear tire if the rear shocks should bottom out

Incoming search terms: