SUZUKI SV1000/ S SERVICE MANUAL Supplimentary

0

Filed Under (Suzuki) by admin on 26-02-2011

download
CHASSIS BOLT AND NUT Check that all chassis bolts and nuts are tightened to their specified torque. (Refer to below and page 2-29 of SV1000S Service manual for the locations of the following nuts and bolts on the motorcycle.) CHASSIS FRONT FORK REMOUNTING Align the upper surface A of the inner tube with the upper surface B of the steering stem upper bracket. Tighten initially at 1 000 km (600 miles, 1 month) and every 6 000 km (4 000 miles, 6 months) thereafter. ITEM N·m kgf-m lb-ft 1 Handlebar clamp bolt 23 2.3 16.5 2 Handlebar holder set nut 45 4.5 32.5 SV1000K3 5 SUSPENSION SETTING After installing the front fork, adjust the spring pre-load and damping force as follows. SPRING PRE-LOAD ADJUSTMENT There are eight grooves on the spring adjuster. Position 1 provides the maximum spring pre-load and position 8 provides the minimum spring pre-load. STD position: 7 DAMPING FORCE ADJUSTMENT Rebound damping force Fully turn the damping force adjuster 1 clockwise. It is at stiffest position and turn it out to standard setting position. STD position: 1 and 1/4 turns out from stiffest position Compression damping force Fully turn the damping force adjuster 2 clockwise. It is at stiffest position and turn it out to standard setting position. STD position: 1 turn out from stiffest position STANDARD FRONT SUSPENSION SETTING ! FRONT Spring pre-load adjuster Damping force adjuster Rebound Compression Solo and dual riding 7 1 and 1/4 turns out from stiffest position 1 turn out from stiffest position Be sure to adjust the spring pre-load and damping force on both front fork legs equally. 6 SV1000K3 HANDLEBARS REMOVAL AND DISASSEMBLY Remove the handlebar balancer 1. NOTE: Do not remove the handlebar balancer mounting screw before removing the handlebar balancer. Slightly loosen the mounting screw, and then pull the balancer assembly out of handlebars. Remove the rear view mirror 2. Disconnect the front brake light switch coupler 3. Remove the front brake master cylinder. Remove the right handlebar switch 4 and throttle grip 5. Disconnect the clutch switch lead wires 6. Remove the left handlebar switch 7. Remove the rear view mirror 8. Remove the clutch master cylinder. Remove the handlebar clamp caps

Kymco People 125/ 150 FRONT WHEEL/ FRONT BRAKE/ FRONT SUSPENSION

0

Filed Under (Kymco) by admin on 12-12-2010

download
SERVICE INFORMATION GENERAL INSTRUCTIONS Remove the motorcycle frame covers before removing the front wheel. Jack the motorcycle front wheel off the ground and be careful to prevent the motorcycle from falling down. During servicing, keep oil or grease off the brake drum and brake linings. Contaminated brake disk or brake pads reduce stopping power. Clean the contaminated brake disk with high-performance brake degreaser and replace the brake pads. Do not use brake fluid for cleaning. Bleed air from the brake system if the brake system is removed or the brake is soft. Do not allow any foreign matters to enter the brake system when filling it with brake fluid. Brake fluid will damage painted surfaces and plastic parts. When servicing the brake system, use shop towels to cover and protect rubber, plastic parts and coated surfaces. Wipe off any spilled brake fluid with a clean shop towel. Inspect the brake system before riding. SPECIFICATIONS Item Standard (mm) Service Limit (mm) Axle shaft runout ─ 0.2 Radial ─ 2.0 Axial ─ 2.0 Front brake lining thickness 5.5 2.75 Front shock absorber spring free length 260 252 Brake disk thickness 3.2_3.5 3.0 Brake disk runout ─ 0.25 Brake master cylinder I.D. 12.700_12.74312.75 Brake master cylinder piston O.D. 12.657_12.68412.64 Brake caliper piston O.D. 33.910_33.93433.901 Brake caliper cylinder I.D.

Dynamics and design ofanovel aerodynamically efficient motorcycle

0

Filed Under (Tips and Review) by admin on 01-12-2010

download
Airflow around the ES1-rider combination. The computed aerodynamic drag-area coefficient with the rider in the prone position is C d A=0.16 m2; (B) Airflow around a Yamaha R1-rider combination. The computed aerodynamic drag-area coefficient with the rider in the prone position is C d A=0.35 m2. Dynamics and design ofanovel aerodynamically efficient motorcycle 2 In order to facilitate this aerodynamically efficient posture, a number of design changes had to be made to the rider’sseatingposition, to the front and rear suspensions as well as the drivetrain[1]. Amass reduction is attained using a frameless construction in which the suspension components are attached directly to the engine. The new rear drivetrain is illustrated in figure (2). Fig. 2: Novel drivetrain and rear suspension that allows the rider to move his/her feet out of the airstream thereby reducing the machines drag. The new front suspension is shown in figure (3), which allows the rider’storsotoremain out of the airstream. This new low-dive front suspension arrangement also allows for improved engine cooling and compact packaging. Fig. 3: Novel front suspension system that facilitates reduced drag, improved engine cooling and enhanced rider comfort. By reducing aerodynamic drag the ES1 not only provides a design upgrade towards a fuel efficient vehicle, but it also tackles fundamental issues in motorcycle racing. Hence, due toits broad implications to the motorcycle industry, the development and study of the ES1′sdynamicsand design will attracta broad audience since it promises to representa crucial step in the development of the motorcycle

Incoming search terms:

SCOOTERS FRONT WHEEL/ FRONT BRAKE/ FRONT SUSPENSION INSTALLATION

0

Filed Under (Tips and Review) by admin on 01-12-2010

download
FRONT WHEEL REMOVAL Jack the motorcycle front wheel off the ground. Remove the speedometer cable set screw and disconnect the speedometer cable. Remove the front brake cable. Remove the front axle nut and pull out the axle. Remove the front wheel. Remove the front brake panel. INSPECTION AXLE RUNOUT Set the axle in V blocks and measure the runout using a dial gauge. The actual runout is 1/2 of the total indicator reading. Service Limit : 0.2mm replace if over WHEEL RIM Check the wheel rim runout. Service Limits : Radial : 2.0mm replace if over Axial : 2.0mm replace if over Screw Speedometer Cable Front Brake Cable Axle Nut Axle Shaft 12 . FRONT WHEEL/FRONT BRAKE/ FRONT SUSPENSION 12-4 FRONT WHEEL BEARING Remove the side collar and dust seal. Turn the inner race of each bearing with your finger to see if they turn smoothly and quietly. Also check if the outer race fits tightly in the hub. Replace the bearings if the races do not turn smoothly, quietly, or if they fit loosely in the hub. BEARING REPLACEMENT Remove the front wheel bearings and distance collar. Bearing Remover Bearing Remover Head, 12mm Pack all bearing cavities with grease. Drive in the left bearing. Install the distance collar. Drive in the right bearing. Outer driver, 32x35mm Driver handle A Pilot, 12mm

Incoming search terms:

HARLEY DAVIDSON FL SOFTAIL PROFILE LOW FRONT SUSPENSION KIT INSTALLATION

0

Filed Under (Harley Davidson) by admin on 30-11-2010

download
Fork Spring Removal 1. Elevate and support the vehicle so the front tire is off the floor and the forks are fully extended. 4 9 3 1 10 11 2 5 6 7 8 is04004 1. Slider tube cap 2. Spacer washer 3. Oil seal 4. Clamp bolt and washer 5. Fork tube plug 6. O-ring 7. Fork spring 8. Tight-wound end of spring 9. Fork slider tube 10. Fork slider 11. Drain screw and washer Figure 1. Front Fork NOTE Remove the brake caliper from the fork slider. DO NOT remove the brake line from the caliper. 2. Remove the front wheel. See FRONT WHEEL: FLSTC/FLSTF/FLSTN in the Service Manual. 3. Remove the front fender. See FRONT FENDER in the Service Manual. 4. See Figure 1. Remove the slider tube cap (1), spacer (2) and oil seal (3) from the top of one fork side. Save the cap and spacer. The oil seal can be discarded. 5. Loosen the clamp bolt (4) and pull the fork from the brackets. 6. Repeat Steps 4 and 5 for the other fork side. -J00280 1 of 4 Wear saf ety glasses or gog gles when ser vicing f ork assembly. Do not remove slider tube caps without relieving spring preload or caps and springs can fly out, which could result in death or serious injury. (00297a) NOTE Be careful not to damage the O-ring. 7. See Figure 1. Remove the fork tube plug (5) and O-ring (6). Pull the spring (7) out of the slider tube (9). Remove the drain screw and washer (11), and drain the fork. Reinstall the drain screw and washer, and tighten to 52-78 in-lbs (5.9-8.9 Nm). 8. Repeat Step 7 for the other fork side. NOTE The Profile® Low Front Suspension Kit requires a different amount of H-D TYPE E FORK OIL than is listed in the Service Manual. NOTE Measure the oil level from the top of the fork tube with the fork spring removed and the fork fully compressed. 9. See FRONT FORK OIL in the Service Manual, but substitute the measures below. Fill the forks with Harley- Davidson TYPE E FORK OIL: • 1986 through 1999 models: •11.7 oz (345 cc) of oil, or •5.2 inch (132 mm) from top of oil level to top of tube. • 2000 and later models: •13.4 oz (396 cc) of oil, or •4.1 inch (104 mm) from top of oil level to top of tube. Fork Spring Installation 1. Insert a new Profile Low spring (7) from the kit into each slider tube (9), with the tight-wound portion (8) toward the bottom of the fork slider. NOTE Be careful not to damage the O-ring. 2. Install the fork tube plug (5) and O-ring (6) assembly into the slider tube and tighten securely. Be sure that one flat on each fork tube plug faces toward the inside of the fork. 3. Insert both fork side assemblies up through the slider covers, the fork stem and bracket, and the upper bracket. 4. Obtain two new oil seals (3), H-D Part Number 45733-48, and the spacer washers (2) and slider tube caps (1) saved earlier. Place an oil seal, followed by a spacer washer, onto each fork tube plug. 5. Insert the threads of a slider tube cap through each washer and seal, and into the fork tube plugs. Tighten to 40-60 ft- lbs (54.2-81.3 Nm). 6. Tighten the fork stem bracket clamp bolts (4) to 30-35 ft- lbs (40.7-47.5 Nm). 7. Install the front fender. See FRONT FENDER in the Service Manual. Install the front wheel and brake caliper. See FRONT WHEEL: FLSTC/FLSTF/FLSTN in the Service Manual. Jiffy Stand Removal/Installation 1. Move the jiffy stand to the retracted (up) position. Wear safety glasses or goggles when removing or installing spring. Spring tension can cause spring, attached components and/or hand tools to fly out which could result in death or serious injury. (00477c) 2. See Figure 3. Unfasten the jiffy stand leg spring (A) from the vehicle. Remove the hex bolt (B), lock washer (C), flat washer (D) and leg stop (E) from the threaded end of the jiffy stand leg. Discard the jiffy stand leg, but retain all other components. 3. Clean and inspect the jiffy stand attaching parts and mounting bracket for wear or damage. If parts replacement is necessary, refer to the Jiffy Stand section of your Service Manual for replacement procedures

ATK 605 Enduro SPECIFICATIONS

0

Filed Under (Atk) by admin on 16-11-2010

Model : ATK 605 Enduro
Year : 2001
Category: Enduro / offroad
Rating : 75.3 out of 100
Engine and transmission
Displacement: 597.00 ccm (36.43 cubic inches)
Engine type: Single cylinder, four-stroke
Power: 48.00 HP (35.0 kW)) @ 7200 RPM
Bore x stroke: 97.0 x 81.0 mm (3.8 x 3.2 inches)
Valves per cylinder: 4
Fuel system: Carburettor
Gearbox: 5-speed
Transmission type,
final drive: Chain
Chassis, suspension, brakes and wheels
Front suspension travel: 300 mm (11.8 inches)
Rear suspension travel: 330 mm (13.0 inches)
Front tyre dimensions: 80/100-21
Rear tyre dimensions: 110/100-18
Front brakes: Single disc
Front brakes diameter: 260 mm (10.2 inches)
Rear brakes: Single disc
Rear brakes diameter: 220 mm (8.7 inches)
Physical measures and capacities
Dry weight: 127.0 kg (280.0 pounds)
Power/weight ratio: 0.3780 HP/kg
Seat height: 925 mm (36.4 inches) If adjustable, lowest setting.
Wheelbase: 1,498 mm (59.0 inches)
Fuel capacity: 16.00 litres (4.23 gallons)

Cobra Motorcycle and ATV Specifications CX65 CX50 Sr. (The King) CX50 Jr. ECX 70 ECX 50 ECX80AC

0

Filed Under (Cobra) by admin on 14-11-2010

download
Dry Weight 122 lbs 91 lbs 81 lbs 210 lbs 206 lbs 210 lbs Engine Cobra 65cc 2-stroke Cobra 50cc 2-stroke Cobra 50cc 2-stroke Cobra 70cc 2-stroke Cobra 50cc 2-stroke Cobra 80cc 2-stroke Bore x Stroke 44.5mm x 41.7mm 39mm x 41.7mm 39mm x 41.7mm 44.5mm x 44.7mm 39mm x 41.7mm 47.6 mm x 44.7mm Induction Case Reed V-Force® Reed Valve- 24mm Mikuni carb Case Reed Carbon Pedal 19mm carb Case Reed Carbon Pedal 14mm carb Case Reed V-Force® Reed Valve- 24mm Mikuni carb Case Reed Carbon Pedal 21mm carb Case Reed V-Force® Reed Valve- 24mm Mikuni carb Cooling Water cooled Cylinder and Case Water cooled Water cooled Water cooled Cylinder and Case Water cooled Water cooled Cylinder and Case Clutch Hydraulic ally actuated Cobra 3Gx 3-Shoe Cobra 3Gx 3-Shoe Hydraulic ally actuated – (auto option) Cobra 3Gx 3-Shoe Rekluse Z-ball auto-clutch Transmission Six-speed sequential Single-speed auto Single-speed auto Six-speed sequential Single-speed auto Six-speed sequential Exhaust Tuned pipe and silencer Tuned pipe and silencer Tuned pipe and silencer Tuned pipe and silencer Tuned pipe and silencer Tuned pipe and silencer Lubrication Mixture lubrication Mixture lubrication Mixture lubrication Mixture lubrication Mixture lubrication Mixture lubrication Fuel Capacity 1.06 Gallons .85 Gallons .70 Gallons 1.9 Gallons 1.9 Gallons 1.9 Gallons Frame Twin Spar Oval HSLA Double Cradle 4130 ChrMo Steel Double Cradle 4130 ChrMo Steel Arens design twin spar Arens design twin spar Arens design twin spar Wheelbase 1140mm 990 mm 908 mm 1067mm (track 915mm) 1067mm (track 915mm) 1067mm (track 915mm) Seat Height 762mm 680 mm 607 mm 762 mm 737 mm 762mm Ground Clearance 250mm 240 mm 216 mm 205 mm 205 mm 205mm Front Brakes Hydraulic Disk (205mm) Hydraulic Disk (160mm) Hydraulic Disk (160mm) Hydraulic Disk (160mm) Hydraulic Disk (160mm) Hydraulic Disk (160mm) Rear Brakes Hydraulic Disk (165mm) Hydraulic Disk (140mm) Adjustable Drum Hydraulic Disk (180mm) Hydraulic Disk (180mm) Hydraulic Disk (180mm) Front Suspension Marzocchi 35mm USD Adjustable 220mm travel Cobra 30mm USD 210mm travel Marzocchi 32mm 168mm travel Dual A-Arm with SVO™ patented steering design. 248mm travel Dual A-Arm with SVO™ patented steering design. 248mm travel Dual A-Arm with SVO™ patented steering design. 248mm travel Rear Suspension Öhlins Fully Adjustable 270mm travel Fox Piggyback Fully Adjustable 248mm travel Öhlins Piggyback 170mm travel Fox Piggyback 220mm travel Solid axle Fox Piggyback 220mm travel Lightweight tube axle Fox Piggyback 220mm travel Solid axle Wheel Front / Rear 14″ spoke / 12″ spoke (Al rims, Billet hubs, 9ga. spokes) Cobra 12″ Billet Cobra 10″ Billet Cobra 10″ Billet Cobra 10″ Billet ITP 10×5 (4 x1) Al Douglas 8×6.5 (4×2.5) Al ITP 10×5 (4 x1) Al Douglas 8×6.5 (4×2.5) Al ITP 10×5 (4 x1) Al Douglas 8×6.5 (4×2.5) Al Tires Front / Rear 60-100×14 Dunlop 80-100×12 Dunlop 2.5×12 / 2.75×10 2.5×10 / 2.75×10 ITP Holeshot 19/6 ITP 16/6.50-9 ITP Holeshot 19/6 ITP 16/6.50-9 ITP Holeshot 19/6 ITP 16/6.50-9

Incoming search terms:

DUCATI 900SS ENGINE/ TRANSMISSION SPECIFICATION

0

Filed Under (Ducati) by admin on 11-11-2010

download
four-stroke V-twin Capacity 864cc Bore x stroke 86 x 74cm Compression ratio 9.5:1 Carburation 2 x 40mm Dell’Orto PHM AD/AS Primary/fi nal drive gear/chain Clutch/gearbox wet multiplate/ fi ve-speed Electrics 12v, Lucas Rita electronic ignition CHASSIS Frame tubular steel open double-cradle Front suspension telescopic forks Rear suspension swinging arm, twin shocks Brakes front/rear 2 x 280mm discs/ 1 x 280mm disc Wheels cast mag alloy Tyres front/rear 100/90 x 18 110/90 x 18 DIMENSIONS Dry weight 452lb/205kg Wheelbase 59in/1498mm Seat height 30in/760mm Fuel capacity 4 gals/18 litres PERFORMANCE Top speed 129mph* Max power 59bhp@ 7400rpm* Fuel consumption 47mpg * I arrive at some sweeping bends and tighter hairpins. So much has been written or said about Ducati handling over the years, and it’s all true. The SS feels light and neutral, and needs only a little pressure on one bar or the other, or a sway of the body, to gently show the way. I take childish pleasure in opening gobfuls of the Tommasselli throttle just to feel the force and hear the Contis bark, and to glory in the sensation of the Duke grunting and pulling through another bend. The Pirelli Match tyres are impressive, and the Marzocchi front end and rear shocks provide a taut, predictable but atypically gentle ride for an Italian superbike. The road opens out, the motor’s spinning at 4500rpm and I’m already doing 90mph, but it’s all so effortless. Ducati got it so right with this one. What fun. What a noise. What a bike

Incoming search terms:

Piaggio MP3 125 Specification

0

Filed Under (Piaggio) by admin on 11-11-2010

download
Capacity 125cc (EURO 3) Engine LEADER 4 valve, 4 stroke single cylinder Cooling Liquid Electric Starter * Transmission Automatic Twist and Go Front Suspension Parallelogram, cantilever Rear Suspension Twin hydraulic shock absorbers with pre-load adjuster Front Brake Disc Double Ø240mm disc Rear Brake Disc Ø240mm disc Wheel Size 12″-12″ Running Weight 208 kg Lockable Glove Box * Underseat Storage Compartment * Digital Clock * Colours Available Sky Blue, Excalibur Silver, Black Graphite, Cherry Red

Piaggio MP3 250ie 250cc specification

0

Filed Under (Piaggio) by admin on 11-11-2010

download
Capacity 250cc (EURO 3) Engine QUASAR 4 valve, 4 stroke single cylinder with electronic injection Cooling Liquid Electric Starter * Transmission Automatic Twist and Go Front Suspension Parallelogram, cantilever Rear Suspension Twin hydraulic shock absorbers with pre-load adjuster Front Brake Disc Double Ø240mm disc Rear Brake Disc Ø240mm disc Wheel Size 12″-12″ Running Weight 213 kg Lockable Glove Box * Underseat Storage Compartment * Digital Clock * Colours Available Sky Blue, Excalibur Silver, Black Graphite, Cherry Red