2000-2001 Honda CBR 929 RR Power Commander installation

0

Filed Under (Honda) by admin on 09-12-2011

download
Remove the main seat. 2) Open the passenger seat hatch. 3) Remove the fuel tank mounting bolts. NOTE: The fuel tank does not need to be removed in order to install the PCII. If you choose to remove the fuel tank to aid in the installa- tion, then all fuel must be drained prior to disconnecting the fuel lines. 4) Locate the main injector harness connector. It is on the right side of the chassis near the fuel hose fitting on the throttle bodies. 5) Disconnect the injector harness connector. 6) Plug the male connector from the PCIIIr into the female connectorm on the main harness (Fig. A). 7) Plug the female connector from the PCIIIr into the male connector from the stock injector harness (Fig. B). 8) Locate the small, red, 2 pin connector (Fig. C) from the crank position sensor. Match the corresponding connectors from the PCIIIr, in-line of the stock wiring harness (Fig. D). 9)Route the harness from the PCIIIr under the fuel tank towards the tail section. 10) Reinstall the fuel tank, make sure not to pinch the PCIIIr harness. 11) Attach the ground wire from the PCIIr to the negative terminal of the battery. (Fig. E) 12) Route the PCIIIr and wiring under the rear seat subframe. Attach to inner fender below passenger seat using supplied velcro (Fig. F). 13) Reinstall the main seat

HARLEY DAVIDSON CHROME FAN KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 02-03-2011

download
INSTALLATION 1. Refer to Service Manual and remove seat. To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) 2. Disconnect battery negative cable. Horn Relocation NOTE This cooling fan is designed to provide supplemental cooling for motorcycles subjected to long periods of idling/parade duty. The fan is mounted on the left side of the engine in the area where the horn is mounted. The stock horn must be removed. Remove Stock Horn 1. Follow Service Manual instructions to remove stock horn and its bracket. 2. Assemble new horn 69043-96B to bracket 69135-04 using screws 3658 and washers 7069. 3. Remove right front fuel tank TORX® screw. 4. Mount horn at front of fuel tank with TORX screw. Verify there is adequate room between horn bracket and fuel tank to prevent paint damage. Tighten screw to 15-20 ft- lbs (20-27 Nm) . 1 is05140a 1. Horn mounting location Figure 1. Horn Relocation Remove Stock Upper Engine Mounting Bracket 1. Remove screw securing rear of fuel tank and gently raise fuel tank to gain access to upper engine mounting bracket. Place suitable blocking under tank. 2. On 2007 models remove bolt attaching stabilizer link to upper engine mounting bracket. 3. Remove two bolts and washers securing upper engine mounting bracket to front and rear cylinder heads. Retain bolts and washers for attaching new upper engine mounting bracket from kit. 4. Note position of fuel hose. Remove upper engine mounting bracket. 5. Connect horn relocation harness to horn. 6. Route stock horn wires forward towards relocated horn. 7. See Figure 7. Cut ends off stock horn wires and strip wires 3/8 inch. Follow instructions in Service Manual, “SEALED

SUZUKI SV650/ S PERIODIC MAINTENANCE CHART

0

Filed Under (Suzuki) by admin on 26-02-2011

download
Item km miles months 1000 6000 12000 18000 24000 600 4000 7500 11000 15000 1 6 12 18 24 Air cleaner Spark plugs Tappet clearance Engine oil Engine oil filter Fuel hose Engine idle speed Carburettor synchronization Evaporative emission control system PAIR air supply system Throttle cable play Clutch cable play Radiator hoses Engine coolant Drive chain Brakes Brake hoses Brake fluid Tires Steering Front forks Rear suspension Exhaust pipe bolt & nut Chassis bolt & nuts – - – R R – I I I – - I I – - – I – - T T Replace every 4 years Replace vapor hose every 4 years – - I – I I I – - Replace every 2 years Clean & lubricate every 600 miles (1000km) Replace every 4 years Replace every 2 years R R R R – - R – I I R I I R I R – Inspect and adjust, clean

HARLEY DAVIDSON BRAIDED STAINLESS STEEL FUEL CROSSOVER LINE KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 11-02-2011

download
INSTALLATION, CARBURETED MODELS Models WITH maxi-fuse: To prevent accidental vehicle start-up, which could cause death or serious injury, remove maxi-fuse before proceeding. (00251a) 1. Refer to the Service Manual and follow the instructions given to remove the maxi-fuse. Models WITHOUT maxi-fuse: To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) 1. Refer to the Service Manual and follow the instructions given to remove the seat and disconnect the negative (black) battery cable from the negative (-) battery terminal. Retain all seat mounting hardware. ALL carbureted models When servicing the fuel system, do not smoke or allow open flame or sparks in the vicinity. Gasoline is extremely flammable and highly explosive, which could result in death or serious injury. (00330a) 2. See FUEL SUPPLY VALVE FILTER: CARBURETED in the Service Manual. a. Turn the fuel supply valve to the OFF (horizontal) position. b. Follow the instructions to disconnect the fuel hose from the fuel supply valve outlet nipple. Drain the fuel from the fuel tank into an adequately sized, approved gasoline container using a vacuum pump (Plastic Mity-Vac hand pump or equivalent). c. Re-install the fuel hose to the fuel supply valve with a new fuel hose clamp (Part Number 10014), purchased separately. d. Proceed to Step

Triumph Oil Filter Mount installation

0

Filed Under (Triumph) by admin on 29-10-2010

download
The Norton filter adapter is then bolted to the rear piece, oil hoses are added, an oil filter is screwed into place, and the assembly is offered to the bike. With the bike supported by straps up on a lift, it will be easy to loosely mount the front clamp section in place and slide the whole assembly up the frame tube. In order to miss the center stand, the filter will need to be as high as possible without the grease nipple striking the top of the adapter. As it ends up, there is “sweet spot” where both the nipple and the stand miss the oil filter by about an 1/8 inch. Tighten the mount down when you find that place. I found that the Norton filter adapter is best plumbed using 5/16 ID black neoprene fuel hose. The spigots on the adapter are 3/8 inch, but it is better to stretch the hose over these that to use easier fitting 3/8 ID hose and then try to shrink it onto the Triumph’s smaller metal oil lines. There will simply be fewer oil leaks using the smaller hose. Be sure that you plumb the filter into the oil line that returns engine oil back to the oil tank. The Triumph oil pump cannot be counted on to create enough vacuum to suction highly viscous motor oil through a very fine filter during cool temperatures. Trying to place the filter on the oil line feeding the engine will quickly result in massive engine damage. It is always better to have the oil pump pushing oil through the filter, and the only way to have RF Whatley, Suwanee, GA 5 Jan 2008 that is to use the return oil line. On all “unit-construction” Triumph engines, the rear-most oil port is the engine oil return. Other Notes • It is generally considered that adding an oil filter will at least quadruple the life of a British motorcycle engine. These motors, which were for the most part perfected in the 1950′s, were designed to run on the older non-detergent oils. In the original design, the oil tank was the oil filter since all particulate debris in the oil settled to the bottom of the oil tank as sediment. All modern engine oils are high-detergent and tend to inhibit the formation of sediment. Therefore most of the fine abrasive in the engine oil continues to circulate unless a filter is added.