HARLEY DAVIDSON WIRE LOOM AND HORNS INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 27-02-2012

download
Remove the stock horn and bracket from the stud it is mounted to and unplug the 2 wires. Remove the seat. Route the end of the wire and hose loom without the connectors. Starting in front of the fuel valve, route this loom behind the valve, over the fuel line over the rear cylinder head along the existing wiring or hoses – if your model has any. Follow the frame to where the back bone and seat support rails come together. Route the loom up into the general area where the compressor will mount (i.e. see diagram). Attach the hose to the ‘Y’ connector on the horns themselves. Attach the two black wires from the loom to the relay terminals #87 and #30, located between the air horns behind chrome cover. Attach the wires from the original horn to the remaining terminals #85 and #86 (NOTE: it makes no difference which wire goes to which terminal). Attach the relay to the back of the horn bracket assembly or up under the fuel tank using the small cable tie provided. NOTE: the terminals must point downward to prevent water from entering the relay! Install the horn assembly using the 1/4″ thick chrome washer provided behind the horn mounting bracket. Use the original acorn nut and tighten securely. Check to see that the horns have at least 1/4″ clearance between the engine, shift linkage and choke knob. They should be horizontal or angle down at the front just slightly. Take any slack out of the loom, keeping it up against the frame and away from the engine or exhaust, using several of the small cable ties provided. COMPRESSOR MOUNTING AND WIRING Due to the vast differences in years and models, it is not possible to have one or two brackets that will fit all models. You may need to mount the compressor in a different position or find an alternative location, such as under one of the side covers. On 2001 and newer Tour models there is room in front of the battery to mount it horizontally. On 1997-2000 fuel injected models, under the front portion of the right hand side cover is an excellent location. On most Softtail models you can attach it to the frame tube behind the rear cylinder. On some models such as Sportsters there may not be a place to conceal the compressor; there is a chrome cover and cap available to dress it up for exposed mounting. (RIVCO part no #CMPCR) If mounting the compressor vertically as pictured, try to keep the end with the electrical terminals pointing downward. You can use the long cable ties provided to attach the compressor to the frame or an existing wiring loom. Once the compressor has been mounted securely, route the hose and one of the wires to it and connect the hose to the air outlet barb or fitting. Trim the wire and crimp on one of the female blade terminals and attach to the (+) terminal. Attach the white ground wire supplied to frame close enough to the compressor, so the wire will reach. Trim and crimp another female terminal to it. Attach this wire to the (-) ground terminal. The remaining black wire from the hose/wire loom goes to the battery (+) terminal through the fuse and holder provided. Trim the black wire allowing for the length and placement of the fuse holder. Crimp together and attach to the battery (+) terminal. Turn ignition on and test horns. Check wires and hoses for neat, secure routing and at least 1″ away from exhaust system. Reinstall seat etc.

2004-2005 KTM 250/ 400/ 450/ 525 Side Panel Fuel Tank removal and Installation Instructions

0

Filed Under (KTM) by admin on 22-01-2012

download
1. Remove airbox cover. Drill stock rivet nut in frame tube through with a ¼” drill as shown in Photo 1. Drill completely through frame tube. We suggest you make a small guide hole in the top of the frame tube first so that you drill straight through the frame member and not come out the side of the frame tube. Photo 1 .Install Lower mounting bracket as shown in Photo 3 noting its orientation. Install the aluminum cone into the recess at the bottom of the stock airbox , then bolt the bracket on with the 6 x 70 mm bolt. Nylock nut threads to top of bolt on top of frame tube as shown in photo 2. Photo 3 2 3. Install the upper mounting bracket shown in Photo 4. Note that in either the MXC or the EXC installation four to six of the 6 x 18 mm fender washers should be installed between the bracket and the subframe. The counter-sunk hole should be positioned toward the rear wheel. Leave the bracket slightly loose until step 6. Photo 4 The best routing for the fuel line (Photo 5 & 6 ) requires drilling holes in the airbox. See Step 4 for hole locations. 4. Drill a 3/8″ hole at the front left corner of the airbox as shown in Photo 6. Make sure the location you choose will not result in the hole coming out behind the frame tube or into the rubber airbox boot. Be very careful drilling this hole.

YAMAHA RAPTOR 350 Removing stock carburetor and cables

0

Filed Under (Yamaha) by admin on 18-01-2012

download
remove seat and gas tank. Make sure fuel petcock is in “off” position. 2. Remove throttle cable paying close attention to routing, as the new cable (s) will need too be routed the same. 3. Remove stock carburetor and stock throttle housing. Stuff a clean, dry rag into manifold to keep debris out of motor. 4. Remove stock air box. 5. Remove choke cable from handlebars. 6. Remove carb vent line from bike. Carburetor installation 1. Carefully trim the rubber alignment tab off of the face of the manifold with a razor blade or side cutters. 2. Remove the hex pipe plug from the carb cap using a 11mm or 7/16 wrench. Do not discard plug, as it will be needed later. Install the metering adjustment tool included in the hardware kit. Do not over-tighten as damage may occur to cap. 3. Attach fuel line to carburetor and secure with clamp. 4. Install remote idle cable into tab on top of carburetor. See main manual for this step. NOTE: Nut must be removed from cable before installation 5. Place carburetor into manifold

Incoming search terms:

Installation & Tuning Instructions For all Motorcycle Applications

0

Filed Under (Tips and Review) by admin on 02-01-2012

download
1) Start with a cold motorcycle, and remove the seat (see owners manual for seat removal instructions). 2) Locate a suitable place for your new PowerCard: It is generally velcroed or zip tied under the seat or behind cowling, check for the easiest mounting and wire routing. Often it is easier to place the card in the desired location, and then pull wires from there, rather than connecting the wires and trying to work the PowerCard backward. (In a 2004 Yamaha R6 for example, it is easiest to mount the card, then route connectors one by one through to the engine compartment.) 3) Disconnect the battery ground. Battery may need to be removed to aid in installation (2006 Yamaha R1 for example). 4) Remove the fuel tank and necessary cowlings – many tanks can simply be rotated up and away to allow access to the fuel injector connectors. Secure the tank. Be careful to prevent fuel spills if fuel line removal is necessary – use the quick-disconnect fittings if your motorcycle is so equipped. (see owners manual for tank removal instructions) a. Note: ZX10 installation also requires removal of the stock air box. Unbolt, disconnect fittings, and then turn clock-wise one-quarter turn to remove. Distributed Exclusively by Moss Motors, Ltd.
3 PowerCard®Instructions Injector lead #3 improperly installed (+) 2 1 (-) 4 3 Distributed Exclusively by Moss Motors, Ltd. 5) Connecting the PowerCard harness inline: a. Remove any one factory fuel injector connector from an injector (a flat blade screwdriver or long nose pliers may be used to ease removal). b. Couple the female connector from the PowerCard onto the fuel injector, and plug the male connector into the ECU/factory wiring harness. c. Repeat for the rest of the fuel injector connectors – The order is not important as long as they are installed as they are paired (in and out)

HARLEY DAVIDSON CRUISE CONTROL KIT FOR FLHR/I AND FLHRS/I MODELS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 15-03-2011

download
INSTALLATION 1. Remove seat, left saddlebag, left side cover and air cleaner assembly following instructions in applicable Service Manual. 2. Review the CRUISE CONTROL-ULTRA MODELS section in the applicable Service Manual before attempting to install this kit. Install Cruise Control Module To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 1. Refer to the appropriate Service Manual and remove bat- tery. 1 is04799 1. Cruise control module mounting hole (3) Figure 1. Battery Box (Right Side View) 2. See Figure 1. In battery box, identify the location of the three mounting holes (1) (on left side of panel) for mounting the cruise control module. 3. See Figure 10. Obtain the cruise control module (1) with cruise cable attached and three grommets (5) from kit. Install the grommets on studs of cruise control module with small diameters outward. 4. See Figure 2. While holding cruise control assembly in place near its mounting location, feed the cruise control cable through the hole in frame crossmember plate and route under rear spark plug wire staying on inner side of fuel line components. Carefully curve cable toward the right and continue routing up under the fuel tank and over the top of the engine stabilizer bracket, then down between cylinder heads. Leave in place temporarily. 5. See Figure 10 and obtain a harness retainer (4) from kit and secure the cruise cable to crossmember plate with barb as shown. On California models, remove the EVAP hose from cable clip and secure hose with one of the cable strap (8)

Incoming search terms:

HARLEY DAVIDSON FRONT TURN SIGNAL RELOCATION KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 23-02-2011

download
REMOVAL When servicing the fuel system, do not smoke or allow open flame or sparks in the vicinity. Gasoline is extremely flammable and highly explosive, which could result in death or serious injury. (00330a) 1. Purge the high-pressure fuel line and disconnect the fuel line following the instructions in the appropriate Service Manual. To prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding. (00251b) 2. Remove the main fuse following the instructions in the appropriate Service Manual. 3. Remove the seat following the instructions in the appropriate Service Manual. Save all seat mounting hardware. NOTE When moving the fuel tank back, do not damage the fuel gauge wires clipped to the frame under the left side of the fuel tank. 4. Remove the front and rear fuel tank mounting hardware following the instructions in the appropriate Service Manual. Move the fuel tank back on the frame to gain access to the tabs on the steering head harness shield. 5. See Figure 1. Disengage the tabs (2) from the holes (3) on each side of the frame and remove the shield (1). 6. Pull the wire harness down from inside the frame enough to disconnect the white (left) [31L] and black (right) [31R] 3-place turn signal connectors. Set aside the frame-side connector halves. 7. Remove the socket terminals from the lamp-side connector halves following the instructions in the appropriate Service Manual. Make note of the wire colors installed in the cavities of each connector, which should be: Left side (white connector): a. Black [BK] wire in cavity 1 b. Violet [V] wire in cavity 2 c. Blue [BE] wire (if installed) in cavity 3 Right side (black connector): a. Black [BK] wire in cavity 1 b. Brown [BN] wire in cavity 2 c. Blue wire [BE] (if installed) in cavity

HARLEY DAVIDSON MINI-TACH WITH SHIFT LIGHT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 15-02-2011

download
INSTALLATION Preparation For EFI models: To prevent spray of fuel, purge system of high-pressure fuel before supply line is disconnected. Gasoline is extremely flammable and highly explosive, which could result in death or serious injury. (00275a) Follow the instructions found in the Service Manual to purge the fuel supply of high pressure gasoline and remove the fuel supply line. For ALL models, WITH Maxi-Fuse: To prevent accidental vehicle start-up, which could cause death or serious injury, remove maxi-fuse before proceeding. (00251a) 1. Refer to the Service Manual and follow the instructions given to remove the Maxi-Fuse. For ALL models, WITHOUT Maxi-Fuse: To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) 1. Refer to the Service Manual and follow the instructions given to remove the seat and disconnect the negative (black) battery cable from the negative (-) battery terminal. Retain all seat mounting hardware. -J04106 Gasoline can drain fr om the carb uretor fuel line when disconnected from fuel valve fitting. Gasoline is extremely flammable and highly explosive, which could result in death or serious injury. Wipe up spilled fuel immediately and dispose of rags in a suitable manner. (00256a) 2. For carbureted models: Turn the fuel supply valve to OFF. Remove the fuel line from the valve. When servicing the fuel system, do not smoke or allow open flame or sparks in the vicinity. Gasoline is extremely flammable and highly explosive, which could result in death or serious injury. (00330a) 3. For ALL models: Follow the instructions in the Service Manual to remove the instrument console from the fuel tank. 4. See FUEL TANK: REMOVAL in the appropriate section (Carbureted or EFI Engine) of the Service Manual for instructions to remove the tank. 5. For all models EXCEPT FLHR or 1986 and later FL Softail models with Chrome Headlight Nacelle Kit (Part Number 67907-96): Follow the instructions in the Service Manual to remove the headlamp housing. For FLHR models, or Softail models WITH the Nacelle Kit: Follow the instructions in the Service Manual and the mini-tach bracket kit (purchased separately) to remove the handlebar shroud. Mini-Tach Bracket Installation 6. For all models except FLHR: Install the mini-tach bracket components per the instructions in that kit. For FLHR models: Follow the instructions in the Service Manual and the mini-tach bracket kit to install the handlebar shroud and bracket components. 7. See Figure 7. Select the rubber isolation gasket (1) from this kit.

Incoming search terms:

Harley-Davidson Carburetors TUNING INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 07-02-2011

download
CARBURETOR REMOVAL Edelbrock recommends consulting an authorized service manual for make, model and year of motorcycle before disassembly of stock parts. 1. Turn fuel valve off before getting started. 2. Disconnect battery to eliminate the possibility of sparks or accidentally engaging the starter. 3. Remove air cleaner assembly. 4. Disconnect choke cable from its bracket. 5. Disconnect fuel line and vacuum lines from carburetor. 6. Gently remove carburetor from manifold. NOTE: For removal of CV style carbs, Edelbrock recommends the carb be gently wiggled from side to side (not up and down) while pulling to get carb out of manifold. MANIFOLD REQUIREMENTS Edelbrock Quick Kits and Complete kits are designed to work with the stock manifold that was OE on your engine. Some aftermarket manifolds will also work with Edelbrock carburetors. S&S “E” Series and Screamin’ Eagle flange mount manifolds will work with Edelbrock flange style carburetors. It is also recommended the manifold being used closely matches the venturi of the carburetor. BIKE PREPARATION 1. Once stock carburetor and air cleaner have been removed, inspect manifold grommet (CV manifolds only) for tears, nicks or cuts. Replace grommet, if damaged. Stuff a clean dry rag into manifold until carb is installed to keep any debris out of engine. 2. Remove old fuel line and vacuum line (if equipped) and install supplied fuel line and vacuum line

HARLEY DAVIDSON HYBRID CAM PLATE AND HIGH FLOW OIL PUMP KIT REMOVAL AND INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 07-02-2011

download
REMOVAL To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative (-) cable first) before proceeding. (00307a) Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 1. Refer to the service manual and follow the instructions to remove the seat and disconnect the battery cables, negative (-) cable first. Retain all seat mounting hardware. Gasoline can drain from the carburetor fuel line when disconnected from fuel valve fitting. Gasoline is extremely flammable and highly explosive, which could result in death or serious injury. Wipe up spilled fuel immediately and dispose of rags in a suitable manner. (00256a) NOTES Installing this kit requires removal and installation of the cam support plate. Refer to the service manual for instructions with the following exception pertaining to cam compartment compo- nents: The crank and primary cam sprocket flange bolts are specially hardened, and the flat washers are of a special diameter and have ground surfaces. Use ONLY the parts provided in the Drive Gear Retention Kit (H-D Part Number 25533-99A, sold separately) when installing this kit. -J04804 1 of 7
The cr ank sprocket flange bolts and pr imary cam sproc ket flange bolts ARE NOT interchangeable. 2. Refer to the service manual to remove and discard the crank sprocket flange bolts and primary cam sprocket flange bolts and washers. 3. For 1999 models only: Refer to the service manual to remove and discard the currently installed cam drive sprocket. 4. Refer to the service manual to remove and disassemble the cams from the support plate and oil pump. Discard the support plate and oil pump. 5. For 1999 – 2000 Dyna, 2000 Softail, 1999 – 2000 Touring, and 2001 EFI Touring models only: Inspect the cams, chain, sprockets and chain tensioners for wear, and replace as needed. Refer to the service manual for inspection and replacement procedures. For 2001 – 2005 Dyna, 2001 – 2006 Softail, 2002 – 2006 Touring, and 2001 carbureted Touring models only: Inspect the cams and secondary cam chain for wear, and replace as needed. Refer to the service manual for inspection and replacement procedures. The primary cam chain, primary sprockets and both tensioners will be replaced by new components from the kit. For ALL models and years: Discard the guide, as it will not be used. INSTALLATION 1. ALL models: See Figure 1. Obtain the new Rear Cam Roller Bearing Kit (H-D Part Number 8983) from inside the Cam Service Kit (H-D Part Number 17045-99C, purchased separately), and install as indicated in Step 2. NOTE See Figure 2. If not enough of the splined shaft is exposed to install the sprocket, omit the spacer (4) and proceed to Step 2e. When the bearing inner race is started onto the machined area, remove the flange bolt (5), flat washer (6) and sprocket, then assemble using the spacer (4). Repeat Step 2e to fully install bearing inner race. To center thrust washer, be sure o-ring is installed in relief groove. Damage to bearing cage and engine can occur if thrust washer is not centered. (00473b) 2. See Figure 1. Install the O-ring (5), thrust washer (4) and bearing inner race (3) onto the rear camshaft as follows: a. See Figure 2. To properly locate the thrust washer (2), install the O-ring (3) in the grinding relief groove on the splined end of the rear camshaft between the machined area and the secondary cam sprocket.

Incoming search terms:

Mikuni HSR 42/ 45 Installation Instructions

0

Filed Under (Mikuni) by admin on 31-10-2010

download
To install, remove the stock carb per Yamaha shop manual procedures. Remove stock throttle cables. Install Mikuni HSR carb into intake manifold and tighten manifold clamp. Install new HSR series throttle cables and adjust cable slack per Yamaha shop manual procedures. Hook fuel line to HSR carb and fasten clamp.* Start motorcycle and fine tune HSR carb for proper running per supplied Mikuni tuning manual. *NOTE: Mikuni HSR series carburetors are designed for gravity-feed fuel systems. You should bypass your stock fuel pump and directly feed your HSR carb right from the fuel petcock. We have noted, though, that you may not be able to get good fuel flow from your Road Star fuel tank in low-fuel situations. You may run your stock fuel pump with the HSR carb, but to do so requires the purchase and installation of an adjustable fuel pressure regulator (set at ½ to 1 lb. of pressure). These are available from most auto parts stores. The stock carb has 2 wires running to the lower rear of the float bowl , these were for a carb warmer, they are not used in this application. Unplug these wires at the main wire harness and retain with your stock carb. The Road Star ignition system uses data from the stock throttle position sensor (TPS) to manage your ignition timing. It is necessary to give the bike this information. You may do so by removing the TPS sensor from the stock carb, leaving it plugged into the main wire harness (the sensor must be fixed to a closed-throttle position), or you may locate the plug for the TPS on the main wire harness and test the leads – you will find one ground, one with .5V and one with 1.5V. Connect the 1.5V to the ground and this will give the bike the same information as stock fully closed throttle.