Yamaha V-Star 650 Jet Kit REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 16-01-2012

download
Remove the vacuum slide from the carburetor. • Remove the OEM needle and spacer, noting the order of assembly. • Counting from the top to the bottom, install the new Baron needle clip on groove #4 of the replacement Baron adjustable needle. • Reinstall the OEM spacer and washer. • Reinstall the vacuum slide along with the diaphragm spring. • Reattach the diaphragm cover and tighten its screws. Note: Verify that the slide maintains a full range of movement! • Drain the fuel from float bowl and remove the bowl cover. • Remove the new cap head Allen screws in place of the OEM Phillips head screws. • Repeat above steps for other OEM main jet and pilot jet, and replace them with Baron’s main and pilot jets. • Thoroughly clean the inside of the float bowl prior to reinstalling it. • Reassemble the carburetor by reversing the order of previous steps. Use thecarburetor. • Locate the fuel mixture plug on each carburetor; it will either be a screw head or a brass plug. If it is a screw head, skip to step c . If you see a brass plug with a small hole in the center, proceed as follows: a. With a 5/32″ drill bit, carefully and slowly drill through the fuel mixture plug for each carburetor. CAUTION: The fuel mixture screw is located directly beneath this plug. Be prepared to stop the drill and remove the bit the instant you break through the plug. b. Insert a self-tapping sheet metal screw into the drilled hole and remove the plug. 311 #1 Industrial Way – Fallbrook, CA 92028 – USA Phone: (760) 731-1200 Fax: (760) 731-1284 E-mail: tech@baronscustom.com Website: www.baronscustom.com Included in this kit: (2) Mikuni main jets, (2) pilot jets, (2) titanium needles, (2) clips, (8) cap head Allen screws Revision 2.0 c. With air/fuel screw now accessible, use a flat blade screwdriver to turn the screw clockwise until it seats, then carefully turn it counter-clockwise 3 turns. Refer to final step for assistance in fine-tuning the setting of the air/fuel adjustment screw. • Reinstall the OEM air filter assembly. • Check all vent lines, fuel lines, and linkage for any obstructions or blockage

Incoming search terms:

HONDA CR250R Owner’s Manual

0

Filed Under (Honda) by admin on 24-04-2011

download
l. CONTROLS( 1 ) Frontbralte tever (2) Throttle grip ( 3 ) Engine stop switch When shutting off engine, press in the  engine stop switch button. (4 ) Rear brake pedal ( 5 I Kickstarter pedal ( 6 } Clutch lever (1′) Fuel tank filler cap ( 8) Gear change pedal The transmission has S speeds. Depress the pedal to Shift into [st gear. Raise the pedal to shift into 2nd, 3rd, 4th and 5th. Neutral is located between 1st and 2nd.  9 ) Fuel mixture enrichment l-mob When starting a cold engne, raise the fuel mixture knob and fully depress the kickstarter pedal. (10) Fuel valve When the fuel valve is turned to "OFF", fuel cannot Flow from the fuel tank to the carburetor. When the fuel valve is turned to “ON”, fuel will flow from the tank to the carburetor. (1 1] Rear shock absorber adjuster The rear shock absorber springs have three settings for precise adjustment of the rear suspension to suit riding conditions and differences in rider weight. Page 6 2 l. OPERATING – Fig. l—2 (1) Fuel tank -  2. FUEL The Honda CRZSUR ELSINORE has a two-stroke engine that requires a gasoline-oil mixture. The capacity of the “fuel tank is 8.59 (2.2 US gal. 1.9 Imp. gal). I Any automotive gasoline with :1 pump octane number of 86 or higher. or research octane number of9i or higher‘ may he used. If “l ofgasoline or a higher octane grade. USE HONDA 2-STROKE INJECTOR OIL OR EQUIVALENT. I Premix gasoline and oil in a ratio of   20:1 Prepare the fuel mixture in a clean container, and shake until thoroughly mixed before Flling the fuel tank. i Too much oil will muse excessive smoking and spark plug fouling. Too little oil will cause engine damage or premature wear. Mix fuel in a ratio of 20 parts gasoline to 1 part oil. I Vegetable oils separate from gasoline more easily than mineral oils, especially in cold weather. It is advisable to use mineral oil when ambient temperatures of below 0°C (32°F) are expected. I If the gasoline-oil mixture is left standing in a container for a long period of time, lubricity will deteriorate. Use the mixture within 24 hours. I Once an oil container is opened, the oil must be used within one month, since oxidation may occur. Do not mix vegetable and mineral oils. Gasoline is flammable and explosive under certain conditions. Always stop the engine and do not smoke or allow open flames or sparks near the motorcycle when refueling

Incoming search terms:

Yamaha Road Star NEEDLE/ JET KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Yamaha) by admin on 10-11-2010

download
1. Remove the vacuum slide from the carburetor. 2. Remove the OEM needle, spacer and washers, noting order of assembly. 3. Counting from the top to the bottom, install the new Baron needle clip on groove #4 for 04-07 models and on groove #5 for 99-03 models of the replacement. NOTE: Baron adjustable needle – The top is the blunt end of the needle. 4. Reinstall the OEM spacer and washers as shown in this diagram. 5. Reinstall the vacuum slide along with the diaphragm spring. 6. Reattach the diaphragm cover back and tighten screws. NOTE: Verify that the slide maintains its full range of movement. 7. Drain the fuel from the float bowl and remove the bowl cover. 8. Remove the OEM main jet and replace it with a Barons genuine Mikuni main jet. Install the correct main jet as indicated in JET SELECTION area above on this page. Our install guides provide a basic outline on the proper installation of our products. Further tuning and/or fitment may be required. Page: 2 BA-2420RD NEEDLE/JET KIT – Yamaha Road Star (99-07) 9. Thoroughly clean the inside of the float bowl prior to reinstalling it. 10. Reassemble the carburetor by reversing the order of step #1 through step #10. Use the new cap head allen screws in place of the OEM phillips head screws. 11. Locate the fuel mixture screw – it will either be a screw head or a brass plug. If it is a screw head, skip to step #11c. 11c. If you see a brass plug with a small hole in the center, proceed as follows: With the drill bit, carefully and slowly drill through the fuel mixture plug. CAUTION: The fuel mixture screw is located directly beneath this plug. Be prepared to stop the drill and remove the bit the instant you break through the plug. Insert the self-tapping sheet metal screw into the drilled hole and remove the plug. With air/fuel screw now accessible, use a flat blade screwdriver to turn the screw clockwise until it seats, then carefully turn it counter-clockwise 3 1/2 turns. Refer to step #16 for assistance in fine tuning the setting of the air/fuel adjustment screw. 12. Reinstall the carburetor. We strongly suggest that you attach the throttle cables prior to mounting to intake manifold. 13. Reconnect the fuel line, ensuring the clamp is firmly in place. 14. Reinstall all vent hoses and electrical connectors that were previously removed, checking for any obstructions or blockage. 15. Reinstall the OEM air filter assembly or, if you are installing our Big Air Kit (BAK), follow the instructions that accompany that kit, then continue with next step. NOTES: When the BAK is installed, the vent hose that terminated on the rear of the OEM airbox can be relocated in any safe position that does not kink or pinch it. It is important to verify proper throttle operation before starting the engine.

Incoming search terms:

1991 Bimota YB10 DYNOJET KIT INSTALLATION MANUAL

0

Filed Under (Bimota) by admin on 01-11-2010

download
1. Remove the vacuum slide from the carbs. Remove the stock needles & spacers, noting the order of assembly (Fig.A). 2. Install the Dynojet needles on groove #3 , using all stock spacers (Fig. A). Install the Dynojet washer above the E-clip. 3. Replace the stock slide springs with Dynojet slide springs provided. 4. Remove the stock main jets and replace with the Dynojet main jets provided. Use the DJ116 main jets with stock exhaust pipe, or use the DJ120 main jets with aftermarket header or slip-on with high flowing baffles. Use the DJ112 main jets at high altitude. Be sure that the jets you are changing are the main jets. 5. Locate the fuel mixture plug (Fig. B), if you see a screw head, proceed to adjusting procedure. With the plug drill (DD #5/32) provided, carefully drill thru the plug(s). The mixture screw is directly underneath this plug, be ready to pull back on the drill the instant you break thru. Use the screw provided to secure and remove the plug. Carefully turn mixture screw clockwise until seated, then back out 3 turns. 6. Locate the main air correctors (Fig.C). Using the plugs provided (DCO400), plug the main air passage. Place the plug in the carb flat end first.Tap in lightly. Using DT002. STAGE ONE INSTRUCTIONS Fig. B Place E-clip in groove #3 from the top Fig. A Notes: 1. Proper EXUP value adjustment is very important for good midrange performance. 2. If experiencing fueling problems below 4,000 rpm, under full throttle, that the needle can’t fix, try changing fuel level. If you feel it is too rich, lower the fuel level. If you feel it is too lean, raise the fuel leve

Performance Starts Here RACING CARBURETORS

0

Filed Under (Mikuni) by admin on 31-10-2010

download
Mikuni RS Series Radial Flat Slide carburetors represent the first ever aftermarket true high performance carbs offered to the racing public. Designated the RS for radial slide design, these carbs feature such innovations as: large 34, 36 or 38mm smoothbores, excellent throttle response and streetability, adjustable accelerator pump system, lighter more compact design, quick change needle clip, cam-lock carb synchronizing, horsepower improvement of 25% to 30% and competition priced. • Starter System: Provides fuel enrichment for cold engine starting. • Accelerator Pump Adjust Screws: Sets on and off operation of accelerator pump in relation to throttle slide position. • Adjustable Accelerator Pump: Squirts fuel into carburetor venturi when throttle is opened to improve engine response. • Idle Adjustment Screw: Controls engine idle speed. • Throttle Return Spring: A choice of positioning pegs allows adjustment of spring tension. • Genuine Mikuni Jets: Provide for precise fuel metering. • Pilot Air Jet: in conjunction with the Pilot Fuel Screw for tuning of mixture at idle to 1/4 throttle. • Float Bowl Vent: Allows atmospheric pressure into float bowl for fuel flow. • Smooth Throttle Bore/Venturi: Produces the optimum air and fuel mixture flow at all RPMs. • Jet Needle Clip: Has easy adjustment feature for quick tuning. • Accelerator Pump Spray Nozzle: Shoots fuel directly into the intake tract for immediate engine response. • Flat Throttle Valve Design: Provides the strongest signal for precise and instantaneous throttle response

Kawasaki KFX 700 INSTALLATION and REMOVAL INSTRUCTIONS

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
Jetting (see Picture on next page) 1. Remove vacuum slides from carbs. Remove stock needles & spacers, note order of assembly. 2. Install LTE needles on groove # 4 counting from the top down. 3. Remove stock main jets and replace with the supplied main jets. 4. Locate the fuel mixture screws. Using a flat blade screwdriver, turn the mixture screws clockwise until seated, then turn out 2.5 turns.
FINISHING UP Be sure all wires and hoses are zip-tied back so they will not touch the exhaust. QUIET CORES Quiet cores are supplied with this kit but not installed. To install the quiet cores remove both rear end caps ((turn downs) and install the quiet cores with the tubes facing inward. Re-install the end caps. FIRST RIDE Your first ride after installing exhaust should be no longer than 20 to 30 minutes. Let your ATV cool and re torque all of the hardware on your new exhaust. Silencer Packing

Incoming search terms:

Incoming search terms: