DUCATI MONSTER 696 Owner's manual and maintenance manual

0

Filed Under (Ducati) by admin on 14-12-2010

download
instrument panel (fig. 4) 1) LCD (see page13). 2) Tachometer (rpm). Indicates engine revs per minute. 3) Neutral (N) indicator ( green ). Illuminates when the gearbox is in neutral. 4) Fuel warning light ( yellow ). Illuminates when there are approximately 3litres of fuel left in the tank. 5) Turn signal indicator light ( green ). Illuminates and flashes when the turn signal is in operation. 6) Engine oil pressure warning light ( red ). Illuminates when engine oil pressure is too low. This light should illuminate when the ignition is switched to ON and should go out a few seconds after the engine starts. Important If this light (6) stays on, stop the engine to avoid serious damage. 7) High beam warning light ( blue ). Illuminates when the high beam headlight is on. 8) “EOBD engine diagnostics light” ( amber ). The engine ECU iluminates this light steadily to indicate the presence of errors leading to engine lock. 9) OVER REV indicator lights . Illuminates steadily at 800 rpm before intervention of the revlimiter. Starts flashing when the rev limiter is reached. 5 8 2 4 9 3 1 6 7 fig. 4 12 E 10) 2-position switch A and B . Switch used for displaying and setting instrument panel parameters. It has two positions, A “▲” and B “▼”. 11) High beam headlight flasher switch (fig. 5). The high beam headlight flasher switch is also used for the LAP and USB data aquisition functions. 11 A 10 B fig. 5 13 E LCD – Main functions Warning Any adjustments to the instrument panel must only be carried out when the motorcycle is stationary. Never operate the instrument panel controls while riding the motorcycle. 1) Speedometer . Indicates road speed. 2) Odometer . Shows total distance travelled. 3) Trip meter . Indicates the distance travelled since last reset. 4) Fuel reserve trip counter . Shows distance travelled on reserve fuel. 5) Clock . 6) Air temperature indicator . 7) Lap time . 8) Rev counter (RPM) . 9) Lap time . 8 11 13 12 14 10 4 5 9 6 2 3 1 7 fig. 6 14 E 10) Service indicator (fig. 6). The indicator illuminates to signal when a service is due. The service indiactor will remain on the display until the system is reset by the Ducati Service Centre who carry outthe service. 11) LAP function (fig. 6). Indicates that the LAP has been activated. 12) DDA function (fig. 6). Indicates that the Ducati Data Analyzer (DDA) has been activated. Important The instrument panel incorporates diagnostic functions for the electronic injection/ignition system. The relative menus are for the use of trained personnel only. If you accidentally access this function, turn the key to OFF and have the motorcycle checked at an authorised Ducati Service Centre. 13) Oil temperature indicator (fig. 6). Important Stop riding if the temperature reaches the maximum value, otherwise the engine might be damaged. 14) Ducati Traction Control (DTC) (fig. 6). Indicates activation of the DTC control unit (if present). 15 E LCD – How to set/display parameters At key-on (key turned from OFF to ON ) the instrument panelactivates all the digits of the LCD for 1second and switches on the indicator lights in sequence.

Incoming search terms:

DUCATI MONSTER 1100 / 1100S Owner's manual and maintenance manual

0

Filed Under (Ducati) by admin on 14-12-2010

download
1) Speedometer . Indicates road speed. 2) Odometer . Shows total distance travelled. 3) Trip meter . Indicates the distance travelled since last reset. 4) Fuel reserve trip counter . Shows distance travelled on reserve fuel. 5) Clock . ) Lap time . 7) Rev counter (RPM) . 8) Lap time . 7 10 12 11 13 9 4 5 8 2 3 1 6 fig. 6 14 E 9) Service indicator (fig. 6). The indicator illuminates to signal when a service is due. The service indicator will remain on the display until the system is reset by the Ducati Service Centre whocarry outthe service. 10) LAP function (fig. 6). Indicates that the LAP has been activated. 11) DDA function (fig. 6). Indicates that the Ducati Data Analyzer (DDA) has been activated. Important The instrument panel incorporates diagnostic functions for the electronic injection/ignition system. The related menus are for use by trained personnel only. If you accidentally access this function, turn the key to OFF and have the motorcycle checked at an authorized Ducati Service Centre. 12) Oil temperature indicator (fig. 6). Important Stop riding if the temperature reaches the maximum value, otherwise the engine might be damaged. 13) Ducati Traction Control (DTC) (fig. 6). Indicates activation of the DTC control unit (if present). 15 E LCD – How to set/display parameters At key-on (key turned from OFF to ON ) the instrument panelactivates all the digits of the LCD for 1second and switches on the indicator lights in sequence. OFF CHECK 1 fig. 7 16 E It then reverts to “normal” mode and, in place of the motorcycle speed, shows the model and, for 2 seconds, alsothe version (EU, UK, USA, CND, FRA, JAP). The model is scrolled on the display onceonly. CHECK 2 RUN fig. 8 17 E At Key-On, the instrument panel always shows the following information (de-activating any previously activated functions): Odometer Speed Engine rpm bargraph Engine oil temperature bargraph At this point, with button (1, fig. 9) in position B “▼” it is possible to switch from the odometer display function to thefollowing functions: TRIP TRIP FUEL (only if active) Clock before returning to TOT (odometer function). If, however, you press switch (1, fig. 9) in position A “▲”, thesystem enters MENU mode and displays the following functions in sequence: Error (only if active) BATT RPM LIGHT SET LAP (OFF or ON) LAP MEM DDA (OFF or ON) Erase DDA TIME Set CODE (only if active)

Yamaha YZF-R6 SPECIFICATION AND OWNER'S MANUAL

0

Filed Under (Yamaha) by admin on 19-11-2010

download
Shift timing indicator light This indicator light can be set to come on and go off at the desired engine speeds and is used to inform the rider when it is time to shift to the next higher gear. The electrical circuit of the indicator light can be checked by turning the key to “ON”. If the indicator light does not come on for a few seconds, then go off, have a Yamaha dealer check the electrical circuit. (See pages 3-7-3-10 for a detailed explanation of the function of this indicator light and on how to set it.) EAU04923* Coolant temperature warning light “” This warning light comes on when the engine overheats. When this occurs, stop the engine immediately and allow the engine to cool. The electrical circuit of the warning light can be checked by turning the key to “ON”. If the warning light does not come on for a few seconds, then go off, have a Yamaha dealer check the electrical cir- cuit. Multi-function display The multi-function display is equipped with the following: a speedometer (which shows the riding speed) an odometer (which shows the total distance traveled) two tripmeters (which show the distance traveled since they were last set to zero) a fuel reserve tripmeter (which shows the distance traveled since the fuel level warning light came on) a clock a self-diagnosis device a display brightness and shift timing indicator light control mode NOTE: Be sure to turn the key to “ON” before using the “SELECT” and “RESET” buttons. To switch the speedometer and odometer/tripmeter displays between kilometers and miles, press the “SELECT” button and “RESET” button together for at least two seconds. Odometer and tripmeter modes Pushing the “SELECT” button switches the display between the odometer mode “ODO” and the tripmeter modes “TRIP 1″ and “TRIP 2″ in the following order: ODO → TRIP 1 → TRIP 2 → ODO If the fuel level warning light comes on (see page 3-2), the odometer display will automatically change to the fuel reserve tripmeter mode “F-TRIP” and start counting the distance traveled from that point. In that case, pushing the “SELECT” button switches the display between the various tripmeter and odometer modes in the following order: F-TRIP → TRIP 1 → TRIP 2 → ODO → F-TRIP

YAMAHA TW125 SERVICE MANUAL

0

Filed Under (Yamaha) by admin on 19-11-2010

download
Dimensions: Overall length Overall width Overall height Seat height Wheelbase Minimum ground clearance Minimum turning radius 2,140 mm , 810 mm 1,120 mm , 805 mm 1,330 mm , 260 mm 2,100 mm Basic weight: With oil and full fuel tank 125 kg Engine: Engine type Cylinder arrangement Displacement Bore stroke Compression ratio Compression pressure (STD) Starting system Lubrication system: Air-cooled 4-stroke, SOHC Forward-inclined single cylinder 0.124 L (124 cm3) 57.0 48.8 mm 10.0 : 1 1,200 kPa (12.0 kg/cm2, 12.0 bar) at 1,000 r/min Electric starter Wet sump Oil type or grade: Engine oil API standard: “SE” or higher grade ACEA standard: G4 or G5 Periodic oil change With oil filter replacement Total amount 1.0 L 1.1 L 1.3 L Air filter: Wet type element Fuel: Type Fuel tank capacity Fuel reserve capacity Regular unleaded gasoline 7.0 L 1.0 L 2-2 GENERAL SPECIFICATIONS SPEC Model TW125 Carburetor: Type/quantity Manufacturer Y24P/1 TEIKEI Spark plug: Type Manufacturer Spark plug gap DR8EA NGK 0.6 0.7 mm Clutch type: Wet, multiple-disc Transmission: Primary reduction system Primary reduction ratio Secondary reduction system Secondary reduction ratio Transmission type Operation Gear ratio 1st 2nd 3rd 4th 5th Spur gear 74/20 (3.700) Chain drive 50/14 (3.571) Constant mesh 5 speed Left foot operation 36/16 (2.250) 31/21 (1.476) 27/24 (1.125) 25/27 (0.926) 23/29 (0.793) Brake: Front brake type operation Rear brake type operation Single disc brake Right hand operation Drum brake Right foot operation Suspension: Front suspension Rear suspension Telescopic fork Swingarm (Monocross) Shock absorber: Front shock absorber Rear shock absorber Coil spring/Oil damper Coil gas spring/Oil damper Wheel travel: Front wheel travel Rear wheel travel 160 mm 150 mm Electrical: Ignition system Generator system Battery type Battery capacity C.D.I. C.D.I. magneto GM 7CZ-3D 12 V 7 AH Headlight type: Bulb type Bulb wattage quantity:

Incoming search terms:

Incoming search terms: