2004 Kawasaki ZX10R Power Commander Installation Instructions

0

Filed Under (Kawasaki) by admin on 08-05-2012

download
Remove the main seat and the passenger seat 2. Remove the tail cover by removing the two bolts. 3 Place the Power Commander in the tail section and route the wiring harness on the inside of the tail section towards the front of the bike (Fig. A). 4. Remove the fuel tank. 5. Remove the air box lid by removing the 8 screws around the outer edge (Fig. B). 6. Remove the bolts shown in Fig. C. This will allow you to remove the air box. Fig. A Fig. B Fig. C i212-411 2004-2005 Kawasaki ZX10R – PCIII USB – 2 i212-411 www.powercommander.com Remove these bolts Remove screws Remove bolts 7. Locate the Throttle Position Sensor connector. This connector is located above the left hand side of the engine. This is a white 3 pin connector. Unplug this connector (Fig. D). 8. Plug the white connectors from the PCIII in-line of the stock TPS connector (Fig. E). 9. Locate the fuel rail connector behind the injector bodies (Fig. F). This connector is brown in color

Harley-Davidson MINI-TACH GAUGE KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 05-04-2012

download
1. Refer to the Service Manual and follow the instructions given to remove the Maxi-Fuse. For ALL models, WITHOUT Maxi-Fuse: To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) 1. Refer to the Service Manual and follow the instructions given to remove the seat and disconnect the negative (black) battery cable from the negative (-) battery terminal. Retain all seat mounting hardware. -J03119 1 of Gasoline can drain fr om the carb uretor fuel line when disconnected from fuel valve fitting. Gasoline is extremely flammable and highly explosive, which could result in death or serious injury. Wipe up spilled fuel immediately and dispose of rags in a suitable manner. (00256a) 2. For carbureted models: Turn the fuel supply valve to OFF. Remove the fuel line from the valve. When servicing the fuel system, do not smoke or allow open flame or sparks in the vicinity. Gasoline is extremely flammable and highly explosive, which could result in death or serious injury. (00330a) 3. For ALL models: Follow the instructions in the Service Manual to remove the instrument console from the fuel tank. 4. See FUEL TANK: REMOVAL in the appropriate section (Carbureted or EFI Engine) of the Service Manual for instructions to remove the tank. 5. For all models EXCEPT FLHR or 1986 and later FL Softail models with Chrome Headlight Nacelle Kit (Part Number 67907-96): Follow the instructions in the Service Manual to remove the headlamp housing. For FLHR models, or Softail models WITH the Nacelle Kit: Follow the instructions in the Service Manual and the mini-tach bracket kit (purchased separately) to remove the handlebar shroud.

1982-2005 Harley Motorcycle Removal and Installation Instructions

0

Filed Under (Harley Davidson) by admin on 31-03-2012

download
” bolt from the mounting stem on the Signal® mirror. While seated on the motorcycle, position the Signal® mirror on the handle bar. Secure the Signal® mirror to the handle bar using the 5/ 16 ” bolt. Make sure the bolt is tight! Guide the Signal® mirror wire harness into the cowling by going along side the existing factory wire harness. 4 Remove any slack in the wire harness. Secure the wire harness to the handle bar using a supplied tie wrap. 5 6 Adjust the position of the Signal® mirror and tighten the ball retention screws. Remove the motorcycle seat. Remove the aft mounting bolts on the fuel tank. 7 Guide the Signal® mirror wire harness along the inside of the fuel tank’s front mounting bolt and between the crossover tube. 8 9 Lift up the aft portion of the fuel tank and guide the Signal® mirror wire harness down the backbone of the motorcycle frame, alongside the existing factory wire harness. The motorcycle’s electrical wiring for turn indicators is located aft of the gas tank on the backbone of the frame. Guide the new wire harness from the Signal® mirror to the electrical wiring. Cut off any excess slack in the wire. Locate the SOLID BROWN wire from the wire connector. Turn the ignition key so that electrical power is on and activate the right side turn indicator. Probe the wire with the wire tester to verify that flashing turn indicator power is present. Label that wire as ‘right side turn’. Repeat all of the previous steps to replace the left side factory mirror with the new Signal® mirror. Locate the SOLID VIOLET wire from the wire connector. Activate the left side turn indicator and probe the wire with the wire tester to verify that flashing turn indicator power is present. Label that wire as ‘left side turn

Incoming search terms:

Suzuki C50/ M50 Boulevard BIG AIR KIT INSTALLATION

0

Filed Under (Suzuki) by admin on 13-03-2012

download
1. Remove the (2) Bolts at the top of the stock air cleaner to the left and right of the oval rubber hose coming from under the fuel tank. 2. Loosen the hose clamp at the base of the oval rubber hose on the top of the air cleaner. 3. A male barb protrudes from the rear of the air cleaner that inserts into a rubber grommet mounted to the cylinders. Pull the air cleaner away from the cylinders firmly and you will feel the barb release. Now pull the upper section of the air cleaner downward to remove it from the oval snorkel tube from under the fuel tank. 4. Now you can reach to the rear of the box and unplug the electrical lead for the Air Sensor” which sits just about in the middle of the rear of the air cleaner. Now remove the breather hose at bottom of the air cleaner. 5. Set the air cleaner aside and turn it over to access the back. Remove the single bolt that secures the Air Sensor” (This sensor will be installed into the Aluminum Manifold of your new BAK assembly later) 6. Remove the lower mounting arm assembly from the cylinders. (You will not reuse this). 7. Using the (2) Dome head m6 x 15mm screws install the (2) #1 Arms to the rear (the side without the groove) of the backing plate, the shiny/chrome side of the arms should face outward. The smaller of the two holes in each arm is the one you place the screws through. Use the m6 Flange Nuts to secure the bolts at the rear of backing plate. Snug these up but do not tighten fully.

Incoming search terms:

HARLEY DAVIDSON WIRE LOOM AND HORNS INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 27-02-2012

download
Remove the stock horn and bracket from the stud it is mounted to and unplug the 2 wires. Remove the seat. Route the end of the wire and hose loom without the connectors. Starting in front of the fuel valve, route this loom behind the valve, over the fuel line over the rear cylinder head along the existing wiring or hoses – if your model has any. Follow the frame to where the back bone and seat support rails come together. Route the loom up into the general area where the compressor will mount (i.e. see diagram). Attach the hose to the ‘Y’ connector on the horns themselves. Attach the two black wires from the loom to the relay terminals #87 and #30, located between the air horns behind chrome cover. Attach the wires from the original horn to the remaining terminals #85 and #86 (NOTE: it makes no difference which wire goes to which terminal). Attach the relay to the back of the horn bracket assembly or up under the fuel tank using the small cable tie provided. NOTE: the terminals must point downward to prevent water from entering the relay! Install the horn assembly using the 1/4″ thick chrome washer provided behind the horn mounting bracket. Use the original acorn nut and tighten securely. Check to see that the horns have at least 1/4″ clearance between the engine, shift linkage and choke knob. They should be horizontal or angle down at the front just slightly. Take any slack out of the loom, keeping it up against the frame and away from the engine or exhaust, using several of the small cable ties provided. COMPRESSOR MOUNTING AND WIRING Due to the vast differences in years and models, it is not possible to have one or two brackets that will fit all models. You may need to mount the compressor in a different position or find an alternative location, such as under one of the side covers. On 2001 and newer Tour models there is room in front of the battery to mount it horizontally. On 1997-2000 fuel injected models, under the front portion of the right hand side cover is an excellent location. On most Softtail models you can attach it to the frame tube behind the rear cylinder. On some models such as Sportsters there may not be a place to conceal the compressor; there is a chrome cover and cap available to dress it up for exposed mounting. (RIVCO part no #CMPCR) If mounting the compressor vertically as pictured, try to keep the end with the electrical terminals pointing downward. You can use the long cable ties provided to attach the compressor to the frame or an existing wiring loom. Once the compressor has been mounted securely, route the hose and one of the wires to it and connect the hose to the air outlet barb or fitting. Trim the wire and crimp on one of the female blade terminals and attach to the (+) terminal. Attach the white ground wire supplied to frame close enough to the compressor, so the wire will reach. Trim and crimp another female terminal to it. Attach this wire to the (-) ground terminal. The remaining black wire from the hose/wire loom goes to the battery (+) terminal through the fuse and holder provided. Trim the black wire allowing for the length and placement of the fuse holder. Crimp together and attach to the battery (+) terminal. Turn ignition on and test horns. Check wires and hoses for neat, secure routing and at least 1″ away from exhaust system. Reinstall seat etc.

Incoming search terms:

SUZUKI BOULEVARD M109R Fuel Injected Models INSTALLATION MANUAL

0

Filed Under (Suzuki) by admin on 16-02-2012

download
1. Remove seat, right and left side covers, and fuel tank. 2. Remove airbox. We highly recommend you consult the factory service manual for proper removal of airbox. 3. Route wiring harness as shown in the picture. (Fig 1) 4. Unplug stock wiring harness from injectors and plug in the connectors from Fuelpak as shown. (Fig 2) 5. Unplug the TPS connector (grey) and attach T-tap connectors to the two outside wires. (Fig 3) 6. Route Fuelpak green wire to T-tap on the factory black wire with brown stripe. Routh the Fuelpak violet wire to T-tap on the factory pink wire with black stripe as shown (Fig 3) 7. Reattach the TPS connector. 8. Route red wire to the front of engine and down to the horn. (Fig 4) 9. Disconnect the two position connector from horn and snip connector in half so you have two one-wire connections. 10. Reattach factory grey wire to horn. Attach Fuelpak red wire to the other horn connection. Plug the factory horn orange wire to the male connection on the Fuelpak red wire. 11. Route black wire to battery negative connection as shown. (Fig 5) 12. Attach Fuelpak to Fuelpak harness and mount to bracket under the left side cover as shown. (Fig 6) 13. Before reassembling the bike, make sure handlebar switch is in the engine-not-running position and turn the key on. Fuelpak should light up. Sound the horn. If Fuelpak turns off when the horn is sounded, recheck the red wire connection on the horn and that it is connected to the orange wire from the factory harness. 14. Follow the service manual to reinstall the airbox and gas tank.

Incoming search terms:

SUZUKI GSX-R1300 / HAYABUSA Fuelpak Connectors INSTALLATION MANUAL

0

Filed Under (Suzuki) by admin on 15-02-2012

download
Remove the main seat and passenger seat. 2. Use a prop to hold the tank up in the trunk area. 3. Disconnect the main wiring harness from each of the lower injectors. (Fig 1) 4. Lay the Fuelpak unit in the tail section and route the wire harness down the left side of the motorcycle toward the throttle bodies. 5. Plug the Fuelpak wiring harness in line of the stock wiring harness and injectors. (Fig 2) 6. Locate the throttle position sensor connector on the right hand side of the throttle body. 7. Install the Fuelpak wiring harness TPS connectors in line of the stock wiring harness. (Fig 3) 8. Attach ground wire to the negative side of the battery. 9. Install Fuelpak in the tail section using the supplied velcro. (Fig 4) 10. Bolt the fuel tank back into place. INSTALLATION INSTRUCTIONS FOR P/N 62009 READ ALL INSTRUCTIONS BEFORE BEGINNING INSTALLATION FUEL INJECTION

Suzuki DRZ 400K Dual Sport Kit Installation Manual

0

Filed Under (Suzuki) by admin on 11-02-2012

download
DRZ 400 (Kick Start) Dual Sport Kit Installation Manual 1. Get a degree in Mechanical and Electrical Engineering. (Just kidding!) 2. Remove the side panels, seat, and gas tank. 3. Unplug the headlight from the stock wiring and remove. 4. Unplug the kill button from the stock wiring and remove (Photo 2). The connector is a gray two-conductor connector located under the fuel tank. Release detent on connector to separate. Kill switch connector Photo 2 5. Unplug the stock taillight and remove. Using a utility knife, trim the taillight mounting tabs flush with the underside of the fender. ¼” Photo 3 Countersunk screw and bezel, 4 Places 6. Taillight Installation Position the taillight assembly so that the edge of the red taillight extends past the edge of the fender about 1/4″ as shown in Photo 3. With the taillight positioned as shown Photos 3 & 4 , transfer the four mounting hole locations into the bottom of the fender. Drill the mounting holes at 1/4″ diameter. Use the 6 x 16 mm counter-sunk fasteners and bezels for mounting the taillight

Incoming search terms:

2000-2003 KTM MXC / EXC Dual Sport Kit Installation And Removal Manual

0

Filed Under (KTM) by admin on 08-02-2012

download
00-’03 KTM 400/450/520/525 EXC & MXC Dual Sport Kit Installation Manual 1. Get a degree in Mechanical and Electrical Engineering. (Just kidding!) 2. Remove the seat, fuel tank, and side panels. Stock switch Bracket Photo 2 EXC – Unplug and remove the stock headlight. (Photo 2.) Unplug the stock three-pin taillight connector and pull the taillight wires back to the rear of the airbox temporarily. MXC – Remove the stock front number plate. 3. Make sure the stock battery is oriented in its mounting bracket as shown with the positive terminal on the left side of the bike (as viewed if sitting on the bike). If not, remove and spin it 180 degrees. Photo 3
4. MXC ONLY! (EXC skip this step.) Locate the stock lighting wiring harness zip-tied under the frame back-bone (See Photo 4). Remove the securing zip-ties and route this wiring forward to the area behind the headlight. Route along right side of frame using factory wire- guide clamp. 5. Brake Light Switch Installation: The KTM kit uses a hydraulic brake-switch. This requires replacing the rear master cylinder banjo bolt with a specially made switch. Installing the switch requires bleeding the brake. If you do not feel competent bleeding your rear brake, please refer this job to a qualified mechanic, as failure to do it correctly will make the brake inoperable. Remove the stock banjo bolt and replace with the hydraulic switch as shown. Make sure to install

2000-2003 MXC / EXC Dual Sport Kit Installation Manual

0

Filed Under (KTM) by admin on 05-02-2012

download
1. Get a degree in Mechanical and Electrical Engineering. (Just kidding!) 2. Remove the seat, fuel tank, and side anels. Stock switch Bracket Photo 2 EXC – Unplug and remove the stock headlight. (Photo 2.) Unplug the stock three-pin taillight connector and pull the taillight wires back to the rear of the airbox temporarily. MXC – Remove the stock front number plate. 3. Make sure the stock battery is oriented in its mounting bracket as shown with the positive terminal on the left side of the bike (as viewed if sitting on the bike). If not, remove and spin it 180 degrees