2004 Honda CRF450R OWNER’S MANUAL

0

Filed Under (Honda) by admin on 23-04-2011

download
FUEL Fuel tank capacity: 2.0 US gal (7.4 liter, 1.6 lmp gal) To open the fuel fill cap, pull the breather tube out of thesteering stem nut. Then turn the fuel fill cap ounterclockwise. • Use automobile gasoline with a pump octane number of 92 or higher. If “knocking” or “pinging” oc- curs, try a different brand of gasoline or a higher octane grade. • Gasoline is extremely flammable and is explosive under certain conditions. Perform this operation in a well-ventilated area with the engine stopped. Do not smoke or allow flames or sparks in the area where gasoline is drained or stored and where the fuel tank is refueled. 1.OPERATING INSTRUCTIONS WARNING BASIC OPERATION Starting The Engine • Never run the engine in an enclosed area. The exhaust contains poisonous carbon monoxide gas thatcan cause loss of consciousness and lead to death. • Attempting to start the engine with the transmis- sion in gear and clutch engaged may result in in- jury or damage. NOTE: • This motorcycle can be kickstarted with the transmission in gear by disengaging the clutch before operating the kickstarter. Check the engine oil, transmission oil and coolant levels before starting the engine (page 21, 23, 24). Cold Engine Starting: 1. Turn the fuel valve ON. 2. Shift the transmission into neutral. 3. If the temperature is 35°C (95°F) or below, pull the choke knob fully out. 4. If the temperature is below 0°C (32°F), open the throttle two or three times. (The engine requires a richer mixture for starting in cold weather. When the throttle is so opened, the accelerator pump will feed extra fuel to the cylinder, thereby facilitating starting in cold weather.) 5. With the throttle closed, operate the kickstarter starting from the top of the kickstarter stroke, kick through to the bottom with a rapid, continuous motion. (Do not open the throttle, As the carburetor is equipped with an accelerator pump, excessive fuel will be charged into the engine, and the spark plug will be fouled if the throttle is opened and closed repeatedly. Excessive fuel in the engine makes kick starting difficult.) 6. About a minute after the engine starts, push the choke knob back all the way to fully OFF. If idling is unstable, open the throttle slightly. (1) FUEL FILL CAP (2) BREATHER TUBE WARNING (1) FUEL VALVE (2) CHOKE KNOB Warm Engine Starting: 1. Turn the fuel valve ON. 2. Shift the transmission into neutral. 3. Pull the hot start lever and kick-start the engine. (Do not open the throttle.) 4. As soon as the engine starts, release the hot start lever.

2009 HONDA CBF1000 Specifications/ Press Information

0

Filed Under (Honda) by admin on 18-02-2011

download
Specifications General Model CBF1000 Mold Type ED-type Engine Type Liquid-cooled 4-stroke 16-valve DOHC inline-4 Displacement 998cm³ Bore x Stroke 75 x 56.5mm Compression Ratio 11 : 1 Max. Power Output 72kW / 8,000min-1 (95/1/EC) Max. Torque 93Nm / 6,500min-1 (95/1/EC) Idling Speed 1,200min-1 Oil Capacity 3.6 litres Fuel System Carburation PGM-FI electronic fuel injection Throttle Bore 36mm Aircleaner Dry, cartridge-type paper filter Fuel Tank Capacity 19 litres (including 4-litre reserve) Electrical System Ignition System Computer-controlled digital transistorised with electronic advance Ignition Timing 5° BTDC (idle) ~ 45° BTDC (7,500min-1) Sparkplug Type NGK: CR8EH-9; ND: U24FER9 Starter Electric Battery Capacity 12V / 8.6AH ACG Output 330W Headlights 12V, 55W x 1 (low) / 55W x 2 (high) Drivetrain Clutch Wet, multiplate with coil springs Clutch Operation Hydraulic Transmission 6-speed Primary Reduction 1.604 (77/48) Gear Ratios 1 2.714 (38/14) 2 1.941 (33/17) 3 1.579 (30/19) 4 1.363 (30/22) 5 1.217 (28/23) 6 1.115 (29/26) Final Reduction 2.687 (43/16) Final Drive #530 O-ring sealed chain Frame Type Mono-backbone; rectangular-section steel tube Chassis Dimensions (LxWxH) 2,156 x 781 x 1,138mm Wheelbase 1,480mm Caster Angle 26° Trail 110mm Turning Radius 2.8m Seat Height 795mm (±15mm) Ground Clearance 130mm Kerb Weight 242kg (F: 118kg; R: 124kg), *250kg (F: 120kg; R: 130kg) Max. Carrying Capacity 195kg Loaded Weight 437kg , *445kg Suspension Type Front 41mm cartridge-type telescopic fork, 120mm axle travel Rear Pro-Link with gas-charged HMAS damper, 120mm axle travel Wheels Type FrontHollow-section 6-spoke cast aluminium RearHollow-section 6-spoke cast aluminium Rim Size Front17M/C x MT3.50 Rear17M/C x MT5.00 Tyre Size Front120/70 ZR17M/C (58W) Rear160/60 ZR17M/C (69W) Tyre Pressure Front 250kPa Rear 290kPa Brakes Type Front 296 x 4.5mm dual hydraulic disc with 4-piston (*Combined 3-piston) calipers, floating rotors (*ABS) and sintered metal pads Rear 240 x 6mm hydraulic disc with single-piston (*3-piston) caliper (*ABS) and sintered metal pads

2007 HONDA SILVER WING Specifications / PRESS INFORMATION

0

Filed Under (Honda) by admin on 18-02-2011

download
Specifications Silver Wing ED-type Engine Type Liquid-cooled 4-stroke 8-valve DOHC parallel twin Displacement 582cm³ Bore x Stroke 72 x 71.5mm Compression Ratio 10.2 : 1 Max. Power Output 37kW / 7,000min-1 (95/1/EC) Max. Torque 54Nm / 5,500min-1 (95/1/EC) Idling Speed 1,300min-1 Oil Capacity 2.6 litres Fuel System Carburation PGM-FI electronic fuel injection Throttle Bore 32mm Aircleaner Dry, cartridge-type paper filter Fuel Tank Capacity 16 litres (including 3.5-litre reserve) Electrical System Ignition System Computer-controlled digital transistorised with electronic advance Ignition Timing 12° BTDC (idle) ~ 43° BTDC (8,250min-1) Sparkplug Type CR8EH-9 (NGK); U24FER9 (ND) Starter Electric Battery Capacity 12V / 11AH ACG Output 450W Headlights 12V, 55W x 1 (low) / 55W x 1 (high) Drivetrain Clutch Automatic; centrifugal Transmission V-Matic Final Reduction 6.016 Final Drive V-belt Belt Converter Ratios 2.1 ~ 0.85 Frame Type Centre backbone; steel tube 2/3 Chassis Dimensions (LxWxH) 2,275 x 770 x 1,430mm Wheelbase 1,595mm Caster Angle 28° 30′ Trail 105mm Turning Radius 2.9m Seat Height 740mm Ground Clearance 140mm Dry Weight 218kg (*229.6kg) Kerb Weight 242kg (F: 96.7kg; R: 145.3kg), *247kg (F: 98kg; R: 149kg) Max. Carrying Capacity 180kg Loaded Weight 386kg (F: 141.3kg; R: 244.7kg), *397.4kg (F: 145kg; R: 252.4kg) Suspension Type Front41mm telescopic fork, 120mm axle travel RearDual conventional dampers with 5-step spring preload adjustment, 115mm axle travel Wheels Type FrontU-section triple-spoke cast aluminium RearU-section triple-spoke cast aluminium Rim Size Front14M/C x MT2.75 Rear13M/C x MT4.50 Tyre Size Front120/80 14M/C (58S) Rear150/70 13M/C (64S) Tyre Pressure Front 200kPa Rear 225kPa Brakes Type Front256 x 5mm single disc with Combined 3-piston calliper, (*ABS) and sintered metal pads Rear240 x 6mm hydraulic disc with dual-piston calliper, (*ABS) and sintered metal pads * ABS Version All specifications are provisional and subject to change without notice.

2011 HONDA NT700V Specifications/ Press Information

0

Filed Under (Honda) by admin on 18-02-2011

download
Press information for 2011 NT700V 5 Specifications – NT700V (ED-type) ENGINE Type Liquid-cooled 4-stroke 8-valve SOHC 52° V- twin Displacement 680cm 3 Bore  Stroke 81  66mm Compression Ratio 10 : 1 Max. Power Output 48.3kW/8,000min -1 (95/1/EC) Max. Torque 66.2Nm/6,500min -1 (95/1/EC) Idling Speed 1,200min -1 Oil Capacity 3.2 litres FUEL SYSTEM Carburation PGM-FI electronic fuel injection Throttle Bore 40mm Aircleaner Dry, cartridge-type paper filter Fuel Tank Capacity 19.7 litres (including 3.5-litre reserve) Fuel consumption 20.1 km/l (WMTC Mode #) ELECTRICAL SYSTEM Ignition System Digital transistorised with electronic advance Ignition Timing 10° BTDC (idle) ~ 45° BTDC (8,900min -1 ) Sparkplug Type CPR8EA-9 (NGK) Starter Electric Press information for 2011 NT700V 6 Battery Capacity 12V/11.2AH ACG Output 438W Headlight 12V; 55W  1 (low) / 55W  1 (high) DRIVETRAIN Clutch Wet, multiplate with coil springs Clutch Operation Mechanical; cable-actuated Transmission Type 5-speed Primary Reduction 1.763 (67/38) Gear Ratios 1 2.571 (36/14) 2 1.688 (27/16) 3 1.300 (26/20) 4 1.084 (29/27) 5 0.923 (24/26) Final Reduction 3.091 (34/11) Final Drive Enclosed shaft FRAME Type Diamond; steel twin-spar CHASSIS Dimensions (LWH) 2,218  810  1,320mm (Raised windscreen: 1,491mm) Wheelbase 1,476mm Caster Angle 28° 50′ Trail 115mm
Press information for 2011 NT700V 7 Turning Radius 3.2m Seat Height 805mm Ground Clearance 156mm Kerb Weight 254kg (F: 112kg; R: 142kg) *257kg (F: 113kg; R: 144kg) Max. Carrying Capacity 197kg Loaded Weight 451kg *454kg SUSPENSION Type Front 41mm telescopic fork, 115mm axle travel Rear Single damper with adjustable preload, 122.5mm axle travel WHEELS Type Front S-section triple-spoke cast aluminium Rear S-section triple-spoke cast aluminium Rim Size Front 17  MT3.5 Rear 17  MT4.5 Tyre Size Front 120/70 ZR17 (58W) Rear 150/70 ZR17 (69W) Tyre Pressure Front 250kPa Rear 290kPa (290kPa with passenger) BRAKES Type Front 296  4.5mm dual hydraulic disc with Combined 3-piston calipers and sintered metal pads Press information for 2011 NT700V 8 Rear 276  6mm hydraulic disc with dual-piston caliper and sintered metal pads (*and Combined ABS) *Combined-ABS version

Incoming search terms:

2011 HONDA CBF1000/ CBF1000 ABS Specifications

0

Filed Under (Honda) by admin on 18-02-2011

download
Press information for 2011 CBF1000 / CBF1000 ABS 7 Specifications – CBF1000 (ED-type) ENGINE Type Liquid-cooled 4-stroke DOHC inline-4 Displacement 998cm3 Bore  Stroke 75  56.5mm Compression Ratio 11.2 : 1 Max. Power Output 79kW/9,000r/min -1 (95/1/EC) Max. Torque 96Nm/6,500r/min -1 (95/1/EC) Idling Speed 1,200min -1 Oil Capacity 3.6 litres FUEL SYSTEM Carburation PGM-FI Throttle Bore 36mm Aircleaner Dry, cartridge-type paper filter Fuel Tank Capacity 20 litres Fuel Consumption 18,4 km/l (WMTC Mode #) ELECTRICAL SYSTEM Ignition System Computer-controlled digital transistorised with electronic advance
Press information for 2011 CBF1000 / CBF1000 ABS 8 Ignition Timing 5° BTDC (idle) ~ 45° BTDC (7,500min -1 ) Sparkplug Type IMR8C-9HES Starter Electric Battery Capacity 12V/8.6AH ACG Output 350W/5,000 rpm Headlights 12V, 55W  1 (low) / 55W  1 (high) DRIVETRAIN Clutch Wet, multiplate with coil springs Clutch Operation Hydraulic Transmission Type 6-speed Primary Reduction 1.6 Gear Ratios 1 2.6 2 1.83 3 1.5 4 1.32 5 1.17 6 1.07 Final Reduction 2.687 (43/16) Final Drive #530 O-ring sealed chain FRAME Type Mono-backbone; cast aluminium
Press information for 2011 CBF1000 / CBF1000 ABS 9 CHASSIS Dimensions (LWH) 2,210  780  1,220mm Wheelbase 1,495mm Caster Angle 26° Trail 110mm Turning Radius 2.9m Seat Height 795mm ±15mm Ground Clearance 135mm Kerb Weight *245kg (F: 120kg; R: 125kg) Max. Carrying Capacity 195kg Loaded Weight *440kg SUSPENSION Type Front 41mm free valve-type telescopic fork & adjustable spring; 120mm stroke Rear Gas-charged HMAS damper & adjustable spring and rebound; 120mm axle stroke WHEELS Type Front Hollow-section 6-spoke cast aluminium Rear Hollow-section 6-spoke cast aluminium Rim Size Front 17M/C  MT3.5 Rear 17M/C  MT5
Press information for 2011 CBF1000 / CBF1000 ABS 10 Tyre Size Front 120/70 ZR17M/C (58W) Rear 160/60 ZR17M/C (69W) Tyre Pressure Front 250kPa Rear 290kPa (290kPa with passenger) BRAKES Type Front 296  4.5mm dual hydraulic disc with 2- piston calipers, floating rotors, sintered metal pads (*3-piston calipers and Combined ABS) Rear 240  5.0mm hydraulic disc with 1-piston caliper, sintered metal pads (*and Combined ABS) *C-ABS version All specifications are provisional and subject to change without notice

Incoming search terms:

2007 HONDA CRF450X Specifications / PRESS INFORMATION

0

Filed Under (Honda) by admin on 18-02-2011

download
Specifications CRF450X ED-type Engine Type Liquid-cooled 4-stroke 4-valve SOHC single Displacement 449cm³ Bore x Stroke 96 x 62mm Compression Ratio 12 : 1 Max. Power Output 36.2kW / 7,500min-1 (95/1/EC) Max. Torque 46.8Nm / 7,000min-1 (95/1/EC) Fuel System Carburation 40mm Keihin FCR flat-slide carburettor with throttle position sensor (TPS) Fuel Tank Capacity 8.3 litres Electrical System Ignition System Computer-controlled digital capacitor discharge with electronic advance and lighting coil Starter Electric / Primary kick Drivetrain Transmission 5-speed Primary Reduction 2.739 (63/23) Gear Ratio 1 2.231 (29/13) 2 1.625 (26/16) 3 1.235 (21/17) 4 1.000 (19/19) 5 0.826 (19/23) Final Reduction 3.923 (51/13) Final Drive #520 T-ring sealed chain Frame Type Semi-double cradle; aluminium twin-spar Chassis Dimensions (LxWxH) 2,176 x 825 x 1,254mm Wheelbase 1,478mm Caster Angle 27° 17′ Trail 112.8mm Seat Height 963mm Ground Clearance 348mm Dry Weight 115.7kg Kerb Weight 122.6kg 8/9 Suspension Type Front47mm Showa inverted leading-axle twin-chamber cartridge-type telescopic fork with 16-step adjustable compression and rebound damping; 315mm axle travel RearPro-Link with Showa damper, adjustable low-speed (13- step) & high-speed (3.5-turn) compression and 17-step rebound damping; 315mm axle travel Wheels Type FrontAluminium rim/wire spoke RearAluminium rim/wire spoke Rim Size Front21 x 1.6 Rear18 x 2.15 Tyre Size Front80/100 21 (51M) Rear110/100 18 (62M) Brakes Type Front240 x 3mm hydraulic disc with dual-piston calliper and sintered metal pads Rear240 x 4mm hydraulic disc with single-piston calliper and sintered metal pads

Incoming search terms:

2010 HONDA VFR1200F Dual Clutch Transmission Specifications

0

Filed Under (Honda) by admin on 18-02-2011

download
Specifications VFR1200F Dual Clutch Transmission (ED-type/ F-type) ENGINE Type Liquid-cooled 4-stroke UNICAM 76° V-4 Displacement 1237cc Bore  Stroke 81  60mm Compression Ratio 12:1 Max. Power Output ED: 127kW/10,000min-1 (95/1/EC) F: 83kW/9,500min-1 (95/1/EC) Max. Torque ED: 129Nm/8,750min-1 (95/1/EC) F: 115Nm/4,000min-1 (95/1/EC) Idling Speed 1,150 min-1 Oil Capacity 4.9 litres FUEL SYSTEM Carburation PGM-FI electronic fuel injection Aircleaner Oil-permeated, viscous-type paper filter Fuel Tank Capacity 18.5 litres Fuel Consumption ED/E : 15.9 km/l F : 15.9 km/l (tested in D-Mode) (WMTC mode*) VFR1200F 03/05/10 9 9 ELECTRICAL SYSTEM Ignition System Computer-controlled digital transistorised with electronic advance Ignition Timing 8.4° BTDC (idle speed) Sparkplug Type IMR9E-9HES (NGK); VUH27ES (DENSO) Starter Electric Battery Capacity 12V/11.2Ah (YTZ14S) ACG Output 570W Headlights H7x2 (55Wx2) Tail-light 5Wx2,STOP LIGHT 21W( 21/5W+5Wdual-light) DRIVETRAIN Clutch Wet multi-plate, hydraulic, dual Clutch Operation Hydraulic Transmission Type Constant mesh 6-speed Primary Reduction 1.738 (73/42) Gear Ratios 1 2.4666 (37/15) 2 1.7894 (34/19) 3 1.4090 (31/22) 4 1.1600 (29/25) 5 1.0322 (32/31) 6 0.9393 (31/33) VFR1200F 03/05/10 10 10 Final Reduction 2.7061 Final Drive Shaft FRAME Type Diamond; aluminium twin-spar CHASSIS Dimensions (LWH) 2250  740 1220mm Wheelbase 1,545mm Caster Angle 25.5° Trail 101mm Turning Radius 3.5m Seat Height 815mm Ground Clearance 125mm Kerb Weight 277kg Loaded Weight 473Kg SUSPENSION Type Front 43mm cartridge-type telescopic fork with stepless preload adjustment, 120mm axle travel RearPro-Link with gas-charged damper, VFR1200F 03/05/10 11 11 25-step (*stepless remote-controlled hydraulic) preload and stepless rebound damping adjustment, 130mm axle travel WHEELS Type Front 5-spoke hollow gravity Die-cast aluminium Rear7-spoke gravity Die-cast aluminium Rim Size Front 17M/C  MT3.50 Rear 17M/C  MT6.00 Tyre Size Front 120/70 ZR17M/C (58W) Rear 190/55 ZR17M/C (75W) Tyre Pressure Front 250kPa Rear 290kPa BRAKES Type Front 320mm dual floating hydraulic disc with two 6-piston callipers, C-ABS and sintered metal pads Rear276mm hydraulic disc with 2-piston calliper, C-ABS and sintered metal pads All specifications are provisional and subject to change without notice. * Please note that the figures provided are results obtained by Honda under standardized testing conditions prescribed by WMTC. Tests are conducted on a rolling road using a standard version of the vehicle with only one rider and no additional optional equipment. Actual fuel consumption may vary depending on how you ride, how you maintain your vehicle, weather, road conditions, tire pressure, installation of accessories, cargo, rider and passenger weight, and other factors

Incoming search terms:

2011 HONDA XL1000V Specifications / Press Information

0

Filed Under (Honda) by admin on 18-02-2011

download
Specifications – XL1000V / XL1000V ABS (ED-type) ENGINE Type Liquid-cooled 4-stroke 8-valve DOHC 90° V- twin Displacement 996cm 3 Bore  Stroke 98  66mm Compression Ratio 9.8 : 1 Max. Power Output 69kW/7,500min -1 (95/1/EC) Max. Torque 98Nm/6,000min -1 (95/1/EC) Idling Speed 1,300min -1 Oil Capacity 4.1 litres FUEL SYSTEM Carburation PGM-FI electronic fuel injection Throttle Bore 42mm Aircleaner Viscous, cartridge-type paper filter Fuel Tank Capacity 25 litres (including 4-litre warning light reserve) ELECTRICAL SYSTEM Ignition System Computer-controlled digital transistorised with electronic advance Ignition Timing 15° BTDC (idle) ~ 55° BTDC (5,100min -1 ) Sparkplug Type IJR8B9 (NGK) Press information for 2011 XL1000V 6 Starter Electric Battery Capacity 12V/18AH ACG Output 434W Headlight 12V 60W  2 (low) / 55W  2 (high) DRIVETRAIN Clutch Wet, multiplate with coil springs Clutch Operation Mechanical; cable-actuated Transmission Type 6-speed Primary Reduction 1.682 (44/74) Gear Ratios 1 2.571 (14/36) 2 1.684 (19/32) 3 1.292 (24/31) 4 1.100 (30/33) 5 0.969 (32/31) 6 0.853 (34/29) Final Reduction 2.938 (16/47) Final Drive O-ring sealed chain FRAME Type Steel tube CHASSIS DIMENSIONS Dimensions (LWH) 2,300  930  1,465mm Wheelbase 1,560mm Caster Angle 27° 30′ Press information for 2011 XL1000V 7 Trail 110mm Turning Radius 2.58m Seat Height 838mm Ground Clearance 181mm Kerb Weight 268.7kg (F: 126.3kg; R: 142.4kg) *276.7kg (F: 130kg; R: 146.7kg) Max. Carrying Capacity 201kg Loaded Weight 469.7 kg *477.7 kg SUSPENSION Front 43mm telescopic fork, 155mm axle travel Rear Pro-Link damper, 145mm axle travel WHEELS Type Front Hollow-section triple-spoke cast aluminium Rear Hollow-section triple-spoke cast aluminium Rim Size Front 19M/C  MT2.50 Rear 17M/C  MT4.00 Tyre Size Front 110/80 R19M/C (59H) Rear 150/70 R17M/C (69H) Tyre Pressure Front 250kPa Rear 250kPa (with passenger: 280kPa) Press information for 2011 XL1000V 8 BRAKES Front 296  4.5mm dual hydraulic disc with Combined 3-piston calipers (*ABS) and sintered metal pads Rear 256  5mm hydraulic disc with Combined 3- piston caliper (*ABS) and sintered metal pads * Combined-ABS version All specifications are provisional and subject to change without notice

2010 HONDA VT1300CX Specifications/ Press Information

0

Filed Under (Honda) by admin on 18-02-2011

download
Specifications General Model VT1300CX Mold Type ED-type Engine Type Liquid-cooled SOHC 52° V-twin Displacement 1,312cm³ Bore x Stroke 89.5 x 104.3mm Compression Ratio 9.2 : 1 Max. Power Output 42.5kW / 4,250min-1 (95/1/EC) Max. Torque 107Nm / 2,250min-1 (95/1/EC) Idling Speed 900min-1 Oil Capacity 4.3 litres Fuel System Carburation PGM-FI with automatic enricher circuit Throttle Bore 38mm Aircleaner Viscous, cartridge-type mesh net filter Fuel Tank Capacity 12.8 litres Electrical System Ignition System Digital with 3-dimensional mapping, 2 sparks per cylinder Ignition Timing 8° BTDC (idle) ~ 57.7° BTDC (5,250min-1) Sparkplug Type DCPR6E (NGK); XU20EPR-U (DENSO) Starter Electric Battery Capacity 12V / 11.2AH ACG Output 381W Headlights 12V, 55W x 1 (low) / 60W x 1 (high) Drivetrain Clutch Wet, multiplate with coil spring Transmission 5-speed Primary Reduction 1.758 Gear Ratios 1 1.900 2 1.231 3 0.912 4 0.757 5 0.676 Final Reduction 2.661 Final Drive Shaft Frame Type Double-cradle; steel Chassis Dimensions (LxWxH) 2,575 x 900 x 1,150mm Wheelbase 1,805mm Caster Angle 32° Trail 90mm Turning Radius 4.1m Seat Height 678mm Ground Clearance 126mm Kerb Weight 303kg (F: 128kg; R: 175kg), *309kg (F: 131kg; R: 178kg) Max. Carrying Capacity 160kg Loaded Weight 463kg , *469kg Suspension Type Front 45mm telescopic fork with 130mm stroke and 102.4mm axle travel Rear Monoshock with adjustable rebound damping and 35-position spring preload adjustability, 95mm axle travel Wheels Type Front9-spoke cast aluminium Rear7-spoke cast aluminium Rim Size Front21M/C x MT2.15 Rear18M/C x MT6.25 Tyre Size Front90/90 R21M/C () Rear200/50 R18M/C () Tyre Pressure Front 225kPa Rear280kPa (with passenger: 280kPa) Brakes Type Front 336mm single disc with twin-piston caliper (*Combined 3-piston calliper and ABS) Rear 296mm disc with single-piston caliper (*Combined twin piston and ABS) * C-ABS version

2011 HONDA CRF250X Specifications

0

Filed Under (Honda) by admin on 18-02-2011

download
Specifications CRF250X (ED-type) ENGINE Type Liquid-cooled 4-stroke 4-valve SOHC single Displacement 249cm 3 Bore  Stroke 78  52.2mm Compression Ratio 12.9 : 1 Max. Power Output 21.9kW/9,000min -1 (95/1/EC) Max. Torque 24.2kW/8,000min -1 (95/1/EC) FUEL SYSTEM Carburation 37mm Keihin FCR flat slide carburettor with throttle position sensor (TPS) Fuel Tank Capacity 7.3 litres (including 1.6-litre reserve) ELECTRICAL SYSTEM Ignition System Computer-controlled digital capacitor discharge with electronic advance and lighting coil Starter Electric / Primary kick DRIVETRAIN Transmission 5-speed Primary Reduction 3.611 (65/18) Gear Ratios 1 2.384 (31/13) 2 1.750 (28/16) 3 1.333 (28/21) 4 1.041 (25/24) 5 0.814 (22/27) Final Reduction 3.786 (53/14) Final Drive #520 T-ring roller chain FRAME Type Semi-double cradle; aluminium twin-spar CHASSIS Dimensions (LxWxH) 2,174 x 827 x 1,261mm Wheelbase 1,481mm Caster Angle 27˚ 54′ Trail 118mm Seat Height 958mm Press information for 2011 CRF250X 3 EU-EN Ground Clearance 346mm Kerb Weight 115kg SUSPENSION Type Front 47mm inverted Showa leading-axle twin- chamber cartridge-type telescopic fork with 16-step adjustable compression and rebound damping; 280mm axle travel Rear Pro-Link with single Showa damper, adjustable low-speed (13-step) & high-speed (3.5-turn) compression and 17-step rebound damping; 313mm axle travel WHEELS Type Front Aluminium rim/wire spoke Rear Aluminium rim/wire spoke Rim Size Front 21 x 1.60 Rear 18 x 2.15 Tyre Size Front 90/90-21 M/C 54R Rear 120/90-18 M/C 65R BRAKES Type Front 240  3mm hydraulic disc with dual-piston caliper and sintered metal pads Rear 240  4mm hydraulic disc with single-piston caliper and sintered metal pads

Incoming search terms: