KAWASAKI TERYX EFI Installation Instructions.

0

Filed Under (Kawasaki) by admin on 08-02-2011

download
Basic Tuning Adjustments 1. The following instructions are for basic fuel tuning. Modes 1,2, & 3 are allowing adjustments to increase and decrease the amount of fuel the engine needs. Modes 4 & 5 are for advanced tuning only. DO NOT change modes 4 & 5 when doing basic tuning! 2. To help understand how these modes work, you can think of them as if you were working with a carburetor. 3. Remember each time you push the MODE button you will be advancing to the next mode. Push the MODE button once and you are now in mode 1, push the MODE button again and you are now in mode 2 and so on. You only need to be concerned with modes 1, 2 & 3 for basic tuning. Modes 4 & 5 are for advanced tuning ONLY. 4. If you need to go back to the settings that were pre programmed when you purchased the controller, just look at the picture in each mode, the colored square represents where the settings were when you purchased the controller. 5. Looking at the controller you will see eight lights with numbers under them, this is what you need to look at when changing settings. The #1 light on the controller represents the leanest setting. TRINITY RACING DOES NOT TAKE REPONSIBLITY FOR DAMAGES THAT MAY OCCUR DURING OPERATION OF YOUR VEHICLE UNDER IMPROPER JET SETTINGS. IT IS THE FINAL RESPONSIBLITY OF THE OWNER/RIDER TO ADJUST JETTING TO SPECIFIC RIDING CONDITIONS AND ELEVATION BEFORE RIDING. WARNING! 1.877.FAS TOYS 2.Remove both seats 6. Re-install engine cover and seats. 6. Mode 1 green light represents idle & cruise adjustment (i.e. pilot jet). To adjust this setting push the MODE button once and then push the plus or minus buttons to adjust fuel as needed. 7. Mode 2 yellow light represents an additional amount of fuel added during acceleration (i.e. needle position). To adjust this setting, push MODE twice and then push the plus or minus buttons to adjust fuel as needed. 12 34 56 7 8 12 34 56 7 8 8. Mode 3 red light represents more fuel being added during full throttle (i.e. main jet). To adjust this setting push the MODE button three times and then push the plus or minus buttons to adjust fuel as needed. 9. If you are confident about your tuning skills and feel you need to adjust other parameters, see Advanced Tuning. 12 34 56 7 8 Advanced Tuning Adjustments 1. Advance tuning has two modes in which to adjust. They are called mode 4 and mode 5. In basic tuning, you are changing the amount of fuel that the engine receives, but with advance tuning, you will be changing when the fuel will be available. In each mode you can adjust how soon the fuel delivery occurs. 2. Mode 4 yellow light and blue light represent when the fuel delivery is available during partial throttle acceleration. To adjust this setting, push the MODE button four times and then push the plus or minus buttons to adjust fuel as needed. Only the yellow light will be changing.

Incoming search terms:

2005 Honda CRF450R OWNER'S MANUAL AND COMPETITION HANDBOOK

0

Filed Under (Honda) by admin on 02-12-2010

download
Normal Engine Stop 1. Shift the transmission into neutral. 2. Turn the fuel valve OFF. 3. Lightly open the throttle (1) 2 – 3 times, and then close it. 4. Depress and hold the engine stop button (2) until the engine stops completely. Failure to close the fuel valve may cause the carburetor to overflow, result in hard starting. Emergency Engine Stop To stop the engine in an emergency, press the engine stop button. Basic Operating Instructions 15 Help assure your CRF’s future reliability and performance by paying extra attention to how you ride during the first operating day or 15 miles (25 km). During this period, avoid full-throttle starts and rapid acceleration. This same procedure should be followed each time when: •piston is replaced •piston rings are replaced •cylinder is replaced •crankshaft or crank bearings are replaced Break-in Guidelines 16 Basic Operating Instructions Servicing Your Honda 17 Servicing Your Honda Keeping your CRF well maintained is absolutely essential to your safety. It’s also a good way to protect your investment, get maximum performance, avoid breakdowns, and have more fun. To help keep your CRF in good shape, this section includes a Maintenance Schedule for required servicing and step-by-step instructions for specific maintenance tasks. You’ll also find important safety precautions, information on oils, and tips for keeping your Honda looking good. An ICM (Ignition Control Module) system is used on this motorcycle; consequently, routine ignition timing adjustment is unnecessary. If you want to check the ignition timing, refer to the Honda Service Manual (page 156).

Incoming search terms:

KINROAD 150 SERVICE MANUAL

0

Filed Under (Kinroad) by admin on 27-11-2010

download
FUEL AND OIL RECOMMENDATIONS Be sure to use the specified fuel and oil. FUEL Gasoline should SAE 90# or higher. Unleaded gasoline is recommended. ENGINE OIL SAE10W-30 engine oil of high quality should be used. BREAK-IN PROCEDURE For the first 2 hours of riding, do not exceed 2/3 throttle. Vary engine speed for the first 5 hours. Never hold engine at full throttle for long periods of time. SPECIFICATIONS DIMENSIONS DOUBLE SEAT/SINGLE SEAT Overall Length 2159mm/2075mm Overall Width 1400mm/1235mm Overall Height 1470mm/1400mm Wheelbase 1499mm/1450mm Ground Clearance 170mm/130mm ENGINE Type Forced air-cooled, single cylinder, 4-Stroke Engine Capacity 150cc Displacement 149.5cc Bore x Stroke 57.4mm x 57.8mm Compression Ratio 9.2:1 Max Power 7.4kw/7500rpm Max Torque 9.5N.m/5500rpm Fuel Type SAE 90# or above (unleaded) Lubricate Oil SAE 10W/30 Ignition C.D.I. Starting Electric Spark Plug C7HSA (NGK) Transmission Automatic C. V. T. Carburetor MIKUNI, BS24J Lubrication Force & Splash

Incoming search terms:

Triumph Bonneville Tuning Manual

0

Filed Under (Triumph) by admin on 20-11-2010

download
1. The Float The float bowl acts as a fuel reservoir to meet engine demand. The float is hinged on a pin in the float boss. It rises and falls with the fuel level in the float bowl. The small metal tang integrated in the plastic float supports the float valve, also known as the float needle. As the fuel in the float bowl rises, the float valve is pushed into the valve seat, until it’s high enough to shut off the fuel flow to the bowl. As fuel is used the level in the bowl drops lowering the float which pulls the float valve from its seat, and fills again. Adjusting the height of the float has a big effect on the mixture as a low or high float level makes it harder or easier for the vacuum to suck fuel into the venturi. Differing float levels cause an imbalance which may be perceived as vibration. 2. The Choke This system is referred to as the choke. But that’s a misnomer. When you pull the choke knob, what you’re doing is retracting a plunger that opens a tube connected to the starter jet, allowing additional fuel to enter the venturi just below the vacuum hose nipple. It supplements the pilot system at start up. 3. The Pilot System The primary purpose of the pilot system is to supply the mixture at idle. It continues to supply fuel throughout the entire throttle range, but after about 1/8 throttle is reached the main system starts to put out more of the total mixture, up to full throttle. By adjusting the idle with the big screw on the left side of the carburettors the position of the butterfly is altered, so exposing one or more of the four small holes that are drilled into the venturi, (leading to the pilot jet) just under the butterfly valve, letting more or less air pass the butterfly. Adjusting the pilot screw that’s under the carburettor varies the amount of air premixing with the fuel before it enters the venturi. 4. The Main System Open the throttle and the cable that’s connected to the butterfly valve turns it from vertical to horizontal, so letting more air through the venturi. This increases the vacuum effect that is transferred up through the vacuum drilling in the slide to the diaphragm valve that leads to the diaphragm chamber. The top chamber is separated from the bottom by a rubber diaphragm. The bottom chamber is open to atmospheric pressure from the airbox. When the vacuum in the top chamber rises enough, the constant ambient pressure of the lower chamber helps the diaphragm valve overcome the downward force of the diaphragm spring, so it rises from the ven- turi. As the diaphragm is raised the needle is pulled out of the needle jet, exposing a thinner portion of the needle taper which allows more fuel to rise into the venturi to meet the increased engine demand. The key parts of the main system are shown in the photo below

Incoming search terms:

KTM 250/ 300/ 380 SX,MXC,EXC ENGINE REPAIR MANUAL

0

Filed Under (KTM) by admin on 12-11-2010

download
Repair manual KTM 250 / 300 / 380 Art No 3206004 -E 2-2C main jet jet needle jet needle air control screw idle adjusting screw idle jet throttle valve Idling range A Operation with closed throttle valve. This range is influenced by the position of the air control screw 1 and the idle adjusting screw 2 . Only make adjustments when the engine is hot. To this end, slightly increase the idling speed of the engine by means of the idle adjusting screw. Turning it clockwise produces a higher idling speed and turning the screw counterclockwise produces a lower idling speed. Create a round and stable engine speed using the air control screw (basic position of the air control screw = open by 1.5 turns). Then adjust to the normal idling speed by means of the idle adjusting screw. Opening up B Engine behavior when the throttle opens. The idle jet and the shape of the throttle valve influences this range. If, despite good idling-speed and part-throttle setting, the engine sputters and smokes when the throttle is fully opened and develops its full power not smoothly but suddenly at high engine speeds, the mixture to the carburetor will be too rich, the fuel level too high or the float needle is leaking. Part-throttle range C Operation with partly open throttle valve. This range is only influenced by the jet needle (shape and position). The optimum part-throttle setting is controlled by the idling setting in the lower range and by the main jet in the upper range. If the engine runs on a four-stroke cycle or with reduced power when it is accelerated with the throttle partly open, the jet needle must be lowered by one notch. If then the engine pings, especially when accelerating under full power at maximum engine revs, the jet needle should be raised. If these faults should occur at the lower end of the part throttle range at a four-stroke running, make the idling range leaner; if the engine pings, adjust the idling range richer. Full throttle range D Operation with the throttle fully open (flat out). This range is influenced by the main jet and the jet needle. If the porcelain of the new spark plug is found to have a very bright or white coating or if the engine rings, after a short distance of riding flat out, a larger main jet is required. If the porcelain is dark brown or black with soot the main jet must be replaced by a smaller one. mixture too rich: too much fuel in proportion to air mixture too lean: not enough fuel in proportion to air 1 2 OPERATING RANGES OF THE CARBURETOR 2-3C Carburetor adjustment Basic information on the original carburetor setting The original carburetor setting was adapted for an altitude of approx. 500 meters (1600 ft.) above sea level, and the ambient temperature of approx. 20°C (68°F), mainly for off-road use and central European premium-grade fuel (ROZ 95 MOZ). Mixing ratio 2-stroke motor oil : super fuel 1:40 – 1:60. Basic information on a change of the carburetor setting Always start out from the original carburetor setting. Essential requirements are a clean air filter system, air-tight exhaust system and an intact carburetor. Experience has shown that adjusting the main jet, the idling jet and the jet needle is sufficient and that changes of other parts of the carburetor will not greatly affect engine performance. RULE OF THUMB:

Incoming search terms:

Incoming search terms: