Harley-Davidson Mid Kit POWERLET Installation Instructions

0

Filed Under (Harley Davidson) by admin on 07-05-2012

download
STEP #1 Remove seat. STEP #2 Route wires starting at the battery end and finishing at the bracket. STEP #3 Connect the wires to the socket. STEP #4 Mount the bracket on the horn bracket located under the gas tank. STEP #5 Fasten ty-wraps. STEP #6 Put everything you took off back on. Detailed Instruction: STEP #1 -Remove the seat exposing the battery. See the owner’s manual. STEP #2 – Remove negative battery lead. Remove the positive battery lead and attach the red wire [B]. Attach the black wire to the gas tank bolt [C]. Run the wires below the gas tank by passing through the gap between the frame & gas tank [D]. STEP #3 – Finish routing the wire under the tank and up to the horn bracket. Install the fuse in the fuse-holder. The center terminal is plus and the outer ring is negative (see dwg below). Apply either dielectric grease or Vaseline to the spade terminals. Connect the red wire to the positive spade terminal & the black wire to the negative terminal. Use a voltmeter to check if the polarity is correct. STEP #4 – On the left side of the bike, under the gas tank, locate the horn and bracket. Remove the acorn nut from the bracket [A]. You may need to remove the second nut also. Attach the Powerlet bracket utilizing the supplied chrome & rubber washers (if necessary). Adjust the bracket so it is aligned. Tighten to 8 Nm. STEP #5 – Apply the three ty-wraps. Use one to secure the fuse-holder and the other near point [D] and the third near the socket. Do NOT allow the harness to directly contact the motor or exhaust

HARLEY-DAVIDSON Starter Relay Location Guide

0

Filed Under (Harley Davidson) by admin on 18-04-2012

download
Touring 1998 – 2007 Additional Notes: Relay Location: Under Seat in rubber Boot Battery Connection: Under Seat,Visiable Installation Notes: No Access Issues Factory Relay Type: FULL SIZE Factory Relay Part #: 31504-91A Connection Type: Ground Lug to Battery + Terminial System Relay Replacement: R-S-1 Circuit: Cold C Copywrite 2005 Identity Inv. LLC As of: 11.05 ***2004 – 2007 FLHR series bikes & 2007 FLHX require additional Adaptor AD-1 & DGD-1. Start Relay is in Power Distribution box. Replaces H-D Relay part# 31579-04 Softails 2000 – 2007 Additional Notes: 2000 is when the Softails changed to Twin Cams. Relay Location: Under Seat in covered Power Distribution Box. Battery Connection: Under Seat,Visiable Installation Notes: No Access Issues Factory Relay Type: 1/2 SIZE Factory Relay Part #: 31522-00B Connection Type: Ground Lug to Battery + Terminial System Relay Replacement: R-S-3 Circuit: Cold C Copywrite 2005 Identity Inv. LLC As of: 11.05 Softails 1996 – 1999 Additional Notes: Relay Location: Under Seat in covered Power Distribution Box. Battery Connection: Under Seat,Visiable Installation Notes: No Access Issues Factory Relay Type: FULL SIZE Factory Relay Part #: 31504-91A Connection Type: Ground Lug to Battery + Terminial System Relay Replacement: R-S-1 Circuit: Cold C Copywrite 2005 Identity Inv. LLC As of: 11.05
Dyna 2007 Additional Notes: Relay Location: Under Side Panel Cover. Battery Connection: Replace Batt 15A Fuse with Supplied Fuse Holder Installation Notes: No Access Issues Factory Relay Type: 1/2 SIZE Factory Relay Part #: 31522-00B Connection Type: Tap 12v Fuse (Batt 15A) System Relay Replacement: R-S-3 Circuit: Cold C Copywrite 2005 Identity Inv. LLC As of: 11.05 Dyna 2000 – 2005 Additional Notes: Relay Location: Under Side Panel Cover. Battery Connection: Battery connection is made direct to Battery Buss to right of Relay * see Pic3 Installation Notes: Remove Outer Cover, then Remove 4 bolts holding secondary protector plate in place. Relay is on the upper left. Factory Relay Type: 1/2 SIZE Factory Relay Part #: 31522-00B Connection Type: Ground Lug to Battery Buss + Terminial System Relay Replacement: R-S-3 Circuit: Cold C Copywrite 2005 Identity Inv. LLC As of: 11.05 Pic3 Sportster 2004-2007

Incoming search terms:

Harley Davidson Power Pod Switch Housing Throttle Bracket Installation Instructions

0

Filed Under (Harley Davidson) by admin on 19-03-2012

download
Attach the “Y” bracket to the Power Pod by using the two Power Pod socket head screws that come in your parts kit. (This bracket may already be attached from the factory. ) 2) Remove the two screws on the Right Hand switch housing on your Harley Davidson motorcycle and reinstall them through the two “Y” bracket open holes and back into the switch housing holes. Tighten snugly. In this mounting position, the heads of the two socket head screws holding the “Y” bracket to the Power Pod should be touching the handlebar; this is necessary as it grounds the unit for proper operation. If the unit is not grounded properly, it will not operate. 3) Run the Power Pod’s 60″ power cord to your battery. Make sure as you hide the cord on the way to the battery, that your handlebars turn freely and that the cord does not come in contact with hot engine parts that may melt the wire over time. 4) At some point, before reaching the battery, attach (using the two butt connectors) the in-line fuse holder. TIP: Keeping the in-line fuse holder in an easy to access place (like under a side panel etc) rather than under the seat, may help you service the fuse easier in case of a blown fuse. In most cases, it’s easier to pull a side panel off than it is to remove a seat! 5) Attach the Power Pod lead wire (with in-line fuse now already attached) directly to the battery for power at anytime without using the key. The hot lead can also be run to the fuse box which will require using the ignition switch to “Accessory” or “ON” in some cases. TIP : Always use the in-line fuse for safety. 6) Insert the 20 amp fuse into the in-line fuse holder. Strap down with zip-ties any loose wires and you’re done!

Incoming search terms:

SUZUKI PKT-045 V-STROM LEFT FRONT PANEL Installation Manual

0

Filed Under (Suzuki) by admin on 19-02-2012

download
STEP #1 – Remove the seat & the left side fairings. See the Suzuki service manual. STEP #2 – Drill a 18mm hole into the panel (11/16″ hole saw recommended and is available on our site) where shown [A]. If the hole is too small for the socket open it with emery cloth or a file. Watch the clearance behind the panel; make sure the socket has room. Attach the socket to the panel; use a dab of Silicone on the socket and jam nut. Important: Do NOT use Loctite or over-tighten. STEP #3 – Install the cable starting at the battery through to the front of the bike. Route the cable under the bracket [B]. You’ll find it a bit tight to get through between the frame and motor [C]. Ty-wrap the cable to the frame. Run the cable up to the front fairing. Slip the fuse-holder in the location shown [D]. Disconnect the black and red battery terminals. Connect the ground wire to the bolt [E]. You can cut a notch in the ref boot [F]. Connect the red wire to the battery posts as follows: RED WIRE = BATTERY POSITIVE STEP #4 – Reconnect the positive & negative battery terminals. Install the fuse in the fuse-holder. The center terminal is plus and the outer ring is negative (see dwg below). Apply either dielectric grease or Vaseline to terminals. Connect the red wire to the POSITIVE terminal and the black wire to the NEGATIVE terminal. Use a voltmeter to check if the polarity is correct. STEP #5 – Apply the remaining ty-wrap to the wiring harness where needed. Do NOT allow the harness to directly contact the motor or exhaust.

Honda TRX 400EX INSTALLATION And REMOVAL INSTRUCTIONS

0

Filed Under (Honda) by admin on 14-12-2011

download
Quiet cores are supplied with this kit but not installed. To install the quiet cores remove both rear end caps ((turn downs) and install the quiet cores with the tubes facing inward. Re-install the end caps. REMOVAL Remove seat, disconnect attery and remove. Remove front fenders and side skirts. Remove fuel tank (make sure to shut fuel off and drain remaining fuel in the line before removing). Remove stock muffler first, then remove stock headers. Retain the 4 stock header bolts to install on your new exhaust system. Remove the rear bolt from your stock air box. Loosen stock intake clamp at carburetor. Remove stock boost bottle from the side of the boot. Loosen stock snorkel clamp at the air box, remove stock retaining clip at the front of the snorkel. Remove stock air box, intake boot and snorkel together from the ATV. Slide tarter solenoid off of stock mounting prongs. Remove Phillips screws from fuse holder and remove from plastic housing. Remove plastic battery housing from the ATV. Unplug tail light from harness. Unclip harness from the 2 clips above the battery. CARBURATION Now would be a good time to replace your stock main jet, with the supplied 190 main jet and replace your stock pilot jet with the supplied 48 pilot jet. Make certain that all hoses are tight and routed as stock. Be certain carb clamp is tight when re-installed. INTAKE BOOT Remove the intake boot from the stock air box. Take an exacto knife or razor blade and trim off the rubber piece that the hard plastic snorkel slips into. Trim around the intake boot staying the same distance as the rest of the lip. Take a hax saw and cut the groove as the rest of the boot is, being
careful not to cut all the way through (Picture Fig.2).

Incoming search terms:

Honda ST1300 Front Panel Kit installation

0

Filed Under (Honda) by admin on 17-11-2011

download
STEP #1 – Expose the battery by removing the seat & side panels on the rightnside of the bike. See the Honda service manual. If you are not familiar with this procedure, have a trained technician install the kit. STEP #2 – Drill a 18mm hole into the panel shown [A] (11/16” hole saw recommended and is available on our site). This hole must be drilled in
the correct spot on the panel, make sure it is not too far to the left. If the hole is small for the socket open it with emery cloth or file. There is a coil to the left. Do not install the socket yet. There is a raised lip on the back of the panel. Trim this off so the jam nut will contact the back of the panel evenly. STEP #3 – Attach the socket to the panel; use a dab of Silicone on the socket and jam nut. Important: Do NOT use Loctite or over-tighten; the plastic can crack. STEP #4 – Stretch out the wiring harness. Attach the fuse holder to the support bracket located above the battery [E]. Next remove the negative battery connection, followed by the positive battery connection. Slip the red wire under the red battery boot [C]. You may need to trim the red boot to accommodate the added wire. Connect the red wire to the battery posts as follow

HARLEY DAVIDSON ELECTRA-GLO LIGHT POD KITS INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 08-02-2011

download
INSTALLATION NOTES Clean the controller mounting area and the areas where the light pods will be mounted with soap and water before beginning the installation, and allow to dry thoroughly. Remove debris, dirt and grime from the vehicle areas to be highlighted. Ambient temperature should be at least 50 °F (10 °C) for proper adhesion of the light pods and controller box to vehicle surfaces. Light pods should not be located closer than 2.5 inches (63.5 mm) from exhaust pipes or mufflers, and must have 1.5 inches (38.1 mm) clearance from engine cylinders and heads. Do not install light pods with the light source facing directly away from the vehicle. Installation should be done in a way that allows the light to be seen indirectly by reflecting from chrome or painted surfaces of the vehicle. Prepare the Motorcycle To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative (-) cable first) before proceeding. (00307a) Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 1. Refer to the owner’s manual and follow the instructions given to disconnect the battery cables, negative (-) cable first. NOTE For 2004 and later XL (Sportster®) models, the negative battery cable is most easily disconnected at the engine crankcase . Locate and Install the Controller NOTE Do not mount the controller box in a location where vehicle suspension travel could result in contact with the ON/OFF switch or dimmer control. Damage to the controller box will occur. 2. See Figure 2. Locate the controller box (10) on a flat surface that will allow the red (+) and black (-) leads to reach the battery terminals and the rider to access the controls (with the vehicle parked) and, if necessary, the in-line fuse holder (A). a. Test-fit the controller box to the selected surface before installation. Do not remove the adhesive backing until ready to attach the controller box. b. Clean the controller box mounting area with one of the included alcohol swabs. Allow to dry thoroughly. c. Remove the liner from the adhesive backing of the controller box. Carefully position the controller box to the surface, and press firmly into place. Hold the controller box in position with steady pressure for about one minute. Connect the Battery Cables NOTE Verify that the ignition/light key switch is in the OFF position before attaching the battery cables. 3. Verify that the ignition/key switch is turned to the OFF position. Apply a light coat of Harley-Davidson electrical contact lubricant (part number 99861-02), petroleum jelly or corrosion retardant material to the battery terminals. Connect positive (+) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00068a) 4. Refer to the owner’s manual and follow the instructions given to install first the vehicle’s positive (+) battery cable then the red (+) light pod controller lead ring terminal to the positive (+) battery terminal. Tighten to owner’s manual specifications. Install first the vehicle’s negative (-) battery cable then the black (-) light pod controller lead ring terminal to the negative (-) battery terminal. Tighten to owner’s manual specifications. Arrange the Electra-Glo Light Pods NOTES Electra-Glo light pods (1) can be installed in a variety of locations. They are best installed on a flat surface to provide indirect lighting illuminating mechanical features, vehicle finish or for ground effects. Refer to the notes at the beginning of the Installation section. 5. Select the area or lines of the motorcycle to highlight, and suitable locations for each light pod. DO NOT permanently affix the light pods at this time. Lightly tape the pods in place temporarily until the desired visual effect is achieved Verify clearance from movement of rubber mounted engine or other moving parts, heat sources, or chafe points

Incoming search terms:

Street Magic Magical Wizards LED Installation Instructions

0

Filed Under (Tips and Review) by admin on 29-01-2011

download
1. Always wear appropriate safety gear including safety glasses when soldering or performing any electrical work. It is highly recommended that safety glasses be worn throughout this installation process. Temperature of bike must be at least 60 degrees F. for tape to properly cure. Read all directions before starting project. 2. Turn fuel supply valve to off position before starting. Be sure bike is on level surface and secure and cool. 3. Important: Disconnect negative battery cable from battery; refer to owner’s manual. Failure do to so may result in electrical shock, injury, or fire. Secure negative battery cable away from positive side of battery and all other positive voltage sources on bike. 4. Select hidden locations to mount LED Accent Lights to provide best coverage. 5. Remove fuse from fuse holder. 6. Clean mounting locations on both motorcycle and accent lights with 3M promoter, promoter sponge will dry up quickly, place sponge in sealed plastic bag when not in use. Do not touch 3M promoter with bare fingers. 7. Place piece of double sided tape on accent light if needed, lights come pre-taped on back surface. Trim excess off sides with razor blade. Carefully remove backing from double sided tape and place light on selected mounting location. Press firmly and hold for 10 seconds. Repeat for all lights to be mounted on bike. 8. Route wires from accent lights back to central points near battery compartment under seat. Route wires such that they not interfere with normal operation of bike. Cut off any excess wires, strip back insulation as required. 9. Select several locations to secure wires to frame. Secure wires using tie wraps provided. 10. Join all black wires from LEDs into one Cage Clamp Connector #1. Join all Red wires from LEDs into Cage Clamp Con- nector #2, Join all Blue wires from LEDs into Cage Clamp Connector #3, Join all Green wires from LEDs into Cage Clamp Connector #4. 11. Connect Orange wire from the remote control wire harness to the Red Cage Clamp Connector, connect Blue wire from remote control wire harness to Blue Cage Clamp Connector, connect Green wire from remote control wire harness to Green Cage Clamp Connector. Connect White wire from remote control wire harness to Black Cage Clamp Connector. 12. Crimp spade connector on ends of remaining Red and Black wires from Remote Wiring Harness. Heat spade connector with heat gun so that it shrinks around wire. 13. Connect Red Wire to Positive (+) side of battery, and Black Wire to (-) Side of battery. Take necessary precautions when making connection and refer to bike’s owner’s manual. DO NOT allow any tools to touch both positive (+) side of battery and any metal surface on bike as it will cause a short which could result in serious injury and damage to the battery or other electrical circuits.

VICTORY HAMMER, KINGPIN, VEGAS AND JACKPOT ELECTRIC HORN INSTALLATION INSTRUCTIONS

0

Filed Under (Victory) by admin on 29-01-2011

download
1. Remove the left and right plastic side covers and the seat (two allen bolts located below the sides of the seat). Unplug and remove the stock horn (located over the oil cooler). Connect the female ends of the jacketed two wire cable supplied to the original horn wires. Route the other end of the cable up over the engine and back to where the relay will mount as shown in photo (1). 2. Using the relay supplied with this kit and the wiring diagram provided with the horn set, identify the terminals of the relay (there are very small numbers next to each of the terminal). Connect the two (2) wires from the cable to terminals #85 & 86 on the relay. Locate the fuse holder wire assembly supplied and connect the blade terminal to the relay terminal #87 or #30. Connect the other end of the fuse wire to the battery positive terminal (+). 3. Working under the left side of the motorcycle, refer to photo (2) and install the black bracket supplied as shown onto the engine mount. Locate the four thin flat brackets and two (2) 6mm nuts supplied with the horn set and two lock washers supplied with the kit. Bolt two (2) of the brackets to each of the horns using a lock washer and 6mm nut on each and make them snug. Using the remaining 6 x 12mm bolt, nut and lock washer install the horns onto the black bracket and align as shown in photo (3). Adjust the horn location so that they are free to vibrate and do not come in contact with other parts of the motorcycle then tighten all three 6mmm bolts securely. 4. Using the two remaining wire assembles supplied, connect the larger terminals with double wires to one of the horns and the terminals with the single wire to the other horn. Route these wires up thru the frame to the relay. Connect the wire with the female blade connector to the relay terminal #30 or #87. Connect the ring terminal to the battery negative (-) terminal
or any 6m bolt on the frame. Turn on the ignition and test the horns. Secure the relay to the frame or other wiring and all loose wires using the cable ties supplied. Replace the seat and side covers

Incoming search terms:

Honda Valkyrie Air Horns Installation Instructions

0

Filed Under (Honda) by admin on 29-12-2010

download
Horns: Remove the stock horn by unplugging the wires and removing the 12mm acorn nut. This will leave an 8mm stud exposed. Notice in the hardware kit there are two brackets supplied. Locate the “L” bracket with a tab welded to it. Place the end with an angle cut close to the hole over the stud and secure with the acorn nut see photo(1) . Bolt the horn set to this bracket using the 5/16 ” x ¾” bolt and lock washer. ( NOTE: When installing with “Baker” air wings use the additional bracket, bolt & nut supplied to move the horns forward to clear the air wings) . Hose and wires: Plug the long hose into “Y” fitting on the horn set, plug the gray cord into original horn wires, and wrap the connections with electrical tape. Route both under fuel tank then back to right side cover go behind the ignition switch and between the frame rails. (A piece of stiff wire pushed from the back of the fuel tank to the front will make this much easier, Tape the wires and hose to this wire and pull back through. ) Wiring: See photo (2) Install white wire on compressor (­) terminal. Install red wire onto the compressor (+) terminal. Push hose onto compressor air fitting. Attach compressor to frame tube as shown with hose barb and mounting bolt tab straddling the frame using the two long cable ties provided. NOTE: Be sure air hose is not pinched or kinked. Attach gray cable wire terminal ends to relay terminals #85 and #86. (see wiring diagram) It doesn’t matter which wire goes to which terminal. Attach red wire to one of the remaining relay terminals. Attach the fuse wire to the remaining terminal of the relay. Remove the 1″ x 3″ black plastic cover from the main fuse holder (see photo 2A) . Attach the opposite end of the fuse to the upper­most screw. Re­install the cover. Attach white ground wire to side cover mount ing stud as shown in photo #2B