Harley Davidson sound system Installation Manual

0

Filed Under (Harley Davidson) by admin on 24-02-2012

download
unplug factory radio harness. 2. Plug in Bazooka fast harness into radio and plug factory harness into Bazooka fast harness. ( Fig. 2-1 ) 3. Run red power wire to battery leaving fuse block with the factory fuses. Make sure fuse is removed during install Attach ground wire to triple tree ground terminal. Left side cover. ( Fig. 2-1) 4. Replace factory speakers. All speakers are shipped with grills and in some cases rubber magnet covers. These are for shipping protection only. If rubber magnet covers are on the speakers, they MUST be removed prior to installation. Discard the grills and use the OEM grills to complete the installation. 5. The front and rear speakers are the same. The front speakers must be slid into the speakers mounts with the crossover network placed toward the outside of the fairing and the speaker terminals to the inside for ease of installation. When mounting the rear speakers you must use the spacers provided. Place spacer on the speaker enclosure. Then the speaker and the grill last. The rear speakers should be mounted with the crossover network toward the rear of the bike.

Incoming search terms:

HARLEY DAVIDSON CUSTOM TOURING FRONT BULLET TURN SIGNAL KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 20-04-2011

download
INSTALLATION Outer Fairing/Windshield and Auxiliary Lamp Bracket Removal To prevent accidental vehicle start-up, which could cause death or serious injury, remove maxi-fuse before proceeding. (00251a) 2 3 1 2 is 01215 1. Six-position connector 2. Four-position connector 3. Auxiliary lamp connector Figure 1. Disconnect Signal and Auxiliary Lamp 1. Remove Maxi-Fuse. Refer to SYSTEM FUSES, MAXI- FUSE in Service Manual. NOTE Since the outer fairing screws hold the windshield in place, the windshield may fall to the floor if not removed. 2. Remove the windshield and outer fairing. Refer to UPPER FAIRING/WINDSHIELD in Service Manual for the outer fairing/windshield removal procedure. 3. Disconnect auxiliary lamp and turn signal connectors. NOTE See Figure 1. On 2005 and prior year models, the left and right turn signals plug into a 6-place connector located on the left fairing support brace. On 2006 and later models, each turn signal plugs into its own 4-place connector located toward the bottom of the inner fairing on each side. 4. Using a T40 Torx® drive head, remove and save the four bolts securing the auxiliary head lamp bracket to the chassis. 5. Remove auxiliary lamp bracket from motorcycle. Turn Signal Assembly 1 is 01217 1. Triangular opening Figure 2. Insertion of Terminals Through Triangular Opening 1. See Figure 2. Insert wire terminals through the triangular opening in the turn signal mounting bracket included in the kit. 2. Fit turn signal housing onto bracket. 3. Apply a small amount of Loctite (243) blue (99642-97) to threads of hex head cap screw. 4. Tighten cap screw to 15-20 ft-lbs (20-27 Nm) . -J03753 1 of 2 Turn Signal Installation 1 is 01218 1. Turn signal wire Figure 3. Turn Signal Wire Routing 1. See Figure 3. Insert turn signal connector and wiring between bottom of fairing and top of outer fairing skirt. 2. Route turn signal wire under cutout on mounting bracket and place bracket onto motorcycle. NOTE Care must be taken so the turn signal wire is not pinched between turn signal bracket and motorcycle chassis. 3. Install washers onto turn signal bracket mounting bolts and apply Loctite 243 (blue) (99642-97) to the bolt threads. 4. Tighten mounting bolts to 15-20 ft-lbs (20-27 Nm) . 5. Route turn signal leads toward harness connector. Secure loose wiring with tie straps so wires do not rub against any sharp objects

Incoming search terms: