ULTIMA IGNITION MODULE AND KIT INSTALLATION MANUAL FOR HARLEY DAVIDSON

0

Filed Under (Harley Davidson) by admin on 03-03-2011

download
Disconnect battery. 2. Mark location of timing plate in relation to inside of cam cover. This will give a starting point for timing on new module. Remove old ignition if applicable (see manual) Clymer, Haynes. 3. If your bike is not equipped with timing rotor M/W# 53-528 OEM#32402-83 you must buy one (included in kit). Also a single fire coil is needed (included in kit) M/W# 53-632. Any single fire coil rated 2-4 ohms can be used. NO SOLID CORE PLUG WIRES (copper, silver) they will damage the unit. 4. Install module: helpful hints, early model nose cones, i.e. Shovel Heads, the hole for the wire may need to be drilled out. Align with previously scripted mark for timing. Use lockwashers for stand offs for correct clearance of cover plate. Run wire loom. 5. Connect wires, see wiring diagram. Tape unused wires, green or brown. 12v to tach (brown) will damage module. Set timing. 1996 and later should not be timed 20˚ BTDC as the OEM module, but at 35˚ BTDC. Use this mark when using timing light. If VOESswitch is not used you must ground VOES wire (green) while timing. Refer to manual for correct identification of timing marks. At start up and timing, set spark advance in middle position. FUNCTION SWITCHES LED timing indicator light: When out, shows TDC. When ignition is on, LED will light up. When engine is cranking LED will blink. Electric Start/Kickstart: Set accordingly. VOES/Race mode: VOES switch lets the motor run smoother and improves gas mileage. If you don’t use it or add one tape up green wire and switch to race. VOES switch to use, M/W# 53-652. Spark advance: High compression motors should use race mode and 93 octane or better gas. Changing from VOES to race changes advance curves. Agood rule of thumb is if the engine knocks when throttle is applied in high gear, turn back spark advance curve until it stops engine knock. RPMlimiter: Set at desired RPM to cut engine power. Rear Cylinder: This is for racing and should be set at a dyno. +/-5˚. Rear cylinder timing is achieved through this adjuster. Most should dial to middle setting and leave alone. After all switches are set, install cover with supplied gasket and feel the increased performance of a solid state single fire ignition. Again, we remind you, if you don’t feel confident about installing this unit, let a qualified mechanic do it and be assured you are getting the best performance and gas mileage possible.

Incoming search terms:

Kawasaki Ninja 250 FAQ

0

Filed Under (Kawasaki) by admin on 15-11-2010

download
Am I too small for this motorcycle? Duke – Sun May 14 17:38:31 2000 I’m only about 5’2″ and don’t have a problem, even though I can only touch the ground with the ends of my toes. Once you get a feel for the balance of the bike it’s not hard to keep everything upright. Only place I have trouble is pushing the bike backwards in a parking lot. Usually I just walk the bike (beside it) to where I can get on and get going. How does the EX500 compare to the EX250? Craig M. – Mon May 22 10:23:29 2000 I have both the EX250 and the EX500; both are Y2K models. The 250 is a screamer that performs well and can easily get me into trouble. My only complaints about the 250 are the excessive nose dive when getting on the front brake hard and the skittishness of the rear during high speed cornering. Both are easily corrected with suspension adjustments, I’ve just been too lazy to get the parts and do the work. A bit more wind protection would be great too. The 500 addresses these problems, the diving of the front end (to a degree); the rear’s skittishness and the wind protection. A plus for the 500 is the greater torque and power off the line; it pulls stronger (in my opinion) and will get you into illegal speed territory just a bit quicker than the 250. With greater weight, is has more stability in high speed and windy situations. Insurance is just about the same for both, with the 250 getting the nod for gas mileage. Service requirements are almost identical for both as well, being that they’re both parallel twins, the technology is the virtually the same. The downfalls of the 500: $2K more than the 250 (can do a lot to the 250 with that kind of money); buzzy mirrors, barely useful; heavier weight to have to push around the garage; lesser gas mileage (55-60 MPG; 250 pushes 70 MPG easily); engine is worse than a nervous dog shaking around at idle and at speed (here the 250 is far superior and much smoother). In my opinion, the 500 is a better suited for a larger rider, from a comfort standpoint. I feel I can stretch out a bit more on it than the 250 (I’m 5′ 9″, 160 lbs). The 250′s brakes are better tuned than the 500 and the shifter is much smoother. That may be due to the 3,500 mile difference between the two bikes. Bottom line, both bikes are great, the 250 is now my wife’s ride (mainly) and the 500′s mine (unless she steals the keys away). In time, I’ll make the adjustments to the 250; she doesn’t push it like I do.

Incoming search terms:

Incoming search terms: