Kawasaki 900 / 1100 Engine Removal and Installation

0

Filed Under (Kawasaki) by admin on 01-05-2012

download
1.1 (Above) Remove the two retaining straps, disconnect the battery and remove it from the hull. Disconnect the negative (black) cable first, then the positive (red). Step 2 Intake Removal 2.1 (Below) Remove the eight 10mm bolts securing the flame arrestor cover to the base and remove it. 2.2 (Below) Pull out the flame arrestor screens. 2.3 (Below) Remove the six 10mm bolts securing the flame arrestor base and carbs to the manifold and remove the base. 2.4 (Below) Loosen the gas tank cap to relieve pressure. Be sure the fuel switch is turned to the “OFF” position, and be aware of any fuel that may spill from the hoses. Make sure the hull is clear of any gasoline fumes before continuing work, especially with power tools. Remove the pulse lines from the block, and the three oil lines from the carbs. Move the carbs aside in the hull. 2.5 (Below) Remove the 18 10mm nuts from the studs securing the intake manifold to the engine and remove the manifold

Incoming search terms:

1982-2005 Harley Motorcycle Removal and Installation Instructions

0

Filed Under (Harley Davidson) by admin on 31-03-2012

download
” bolt from the mounting stem on the Signal® mirror. While seated on the motorcycle, position the Signal® mirror on the handle bar. Secure the Signal® mirror to the handle bar using the 5/ 16 ” bolt. Make sure the bolt is tight! Guide the Signal® mirror wire harness into the cowling by going along side the existing factory wire harness. 4 Remove any slack in the wire harness. Secure the wire harness to the handle bar using a supplied tie wrap. 5 6 Adjust the position of the Signal® mirror and tighten the ball retention screws. Remove the motorcycle seat. Remove the aft mounting bolts on the fuel tank. 7 Guide the Signal® mirror wire harness along the inside of the fuel tank’s front mounting bolt and between the crossover tube. 8 9 Lift up the aft portion of the fuel tank and guide the Signal® mirror wire harness down the backbone of the motorcycle frame, alongside the existing factory wire harness. The motorcycle’s electrical wiring for turn indicators is located aft of the gas tank on the backbone of the frame. Guide the new wire harness from the Signal® mirror to the electrical wiring. Cut off any excess slack in the wire. Locate the SOLID BROWN wire from the wire connector. Turn the ignition key so that electrical power is on and activate the right side turn indicator. Probe the wire with the wire tester to verify that flashing turn indicator power is present. Label that wire as ‘right side turn’. Repeat all of the previous steps to replace the left side factory mirror with the new Signal® mirror. Locate the SOLID VIOLET wire from the wire connector. Activate the left side turn indicator and probe the wire with the wire tester to verify that flashing turn indicator power is present. Label that wire as ‘left side turn

Incoming search terms:

Harley Davidson Big Twin EVO Engines Edelbrock Performer-Plus Camshaft , Performer RPM Camshaft , & Performer RPM Camshaft INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 03-03-2012

download
Disconnect the battery. Secure the motorcycle on a suitable stand with the rear wheel off the ground. Remove components necessary for easy access to rocker covers, pushrod covers, and gear case cover, i.e., exhaust system, gas tank, air cleaner, foot rest, etc. Remove spark plugs. 2. Remove top and middle sections of rocker boxes, then rotate engine so both valves are closed on the cylinder head being worked on (put transmission in high gear and move rear wheel to slowly rotate engine). Remove the two 5/16″ bolts nearest the rocker arm shafts (keep all shafts, rocker arms, and pushrods in order so they can be installed in their original position). Remove the pushrod covers and pushrods. NOTE: The use of adjustable time-saver pushrods will simplify installation. Follow the manufacturer’s recommendations for installation of those parts. 3. It is not necessary to remove the tappet guides if you use a cam installation tool such as Crane #9-0020 to hold the tappets in place during cam installation. If you remove the tappet guides, you must use a tappet block alignment tool such as Crane #9- 0021 to re-install the tappet guides. Tappets can be held up in place during removal of guides by using U-shaped piece of safety wire or paper clip hooked to the tappets. 4. Remove ignition covers on gearcase cover by drilling out rivets to gain access to sensor plate. Remove the inner cover, sensor plate and rotor. NOTE: For re-installation, use new rivets H-D #8699 or drill and tap for 10-32 screws. 5. Remove the gearcase cover screws and remove cover while holding end of cam inward. Now remove the camshaft, spacing washer and thrust plate

Incoming search terms:

SUZUKI BOULEVARD M109R Fuel Injected Models INSTALLATION MANUAL

0

Filed Under (Suzuki) by admin on 16-02-2012

download
1. Remove seat, right and left side covers, and fuel tank. 2. Remove airbox. We highly recommend you consult the factory service manual for proper removal of airbox. 3. Route wiring harness as shown in the picture. (Fig 1) 4. Unplug stock wiring harness from injectors and plug in the connectors from Fuelpak as shown. (Fig 2) 5. Unplug the TPS connector (grey) and attach T-tap connectors to the two outside wires. (Fig 3) 6. Route Fuelpak green wire to T-tap on the factory black wire with brown stripe. Routh the Fuelpak violet wire to T-tap on the factory pink wire with black stripe as shown (Fig 3) 7. Reattach the TPS connector. 8. Route red wire to the front of engine and down to the horn. (Fig 4) 9. Disconnect the two position connector from horn and snip connector in half so you have two one-wire connections. 10. Reattach factory grey wire to horn. Attach Fuelpak red wire to the other horn connection. Plug the factory horn orange wire to the male connection on the Fuelpak red wire. 11. Route black wire to battery negative connection as shown. (Fig 5) 12. Attach Fuelpak to Fuelpak harness and mount to bracket under the left side cover as shown. (Fig 6) 13. Before reassembling the bike, make sure handlebar switch is in the engine-not-running position and turn the key on. Fuelpak should light up. Sound the horn. If Fuelpak turns off when the horn is sounded, recheck the red wire connection on the horn and that it is connected to the orange wire from the factory harness. 14. Follow the service manual to reinstall the airbox and gas tank.

Suzuki DRZ 400K Dual Sport Kit Installation Manual

0

Filed Under (Suzuki) by admin on 11-02-2012

download
DRZ 400 (Kick Start) Dual Sport Kit Installation Manual 1. Get a degree in Mechanical and Electrical Engineering. (Just kidding!) 2. Remove the side panels, seat, and gas tank. 3. Unplug the headlight from the stock wiring and remove. 4. Unplug the kill button from the stock wiring and remove (Photo 2). The connector is a gray two-conductor connector located under the fuel tank. Release detent on connector to separate. Kill switch connector Photo 2 5. Unplug the stock taillight and remove. Using a utility knife, trim the taillight mounting tabs flush with the underside of the fender. ¼” Photo 3 Countersunk screw and bezel, 4 Places 6. Taillight Installation Position the taillight assembly so that the edge of the red taillight extends past the edge of the fender about 1/4″ as shown in Photo 3. With the taillight positioned as shown Photos 3 & 4 , transfer the four mounting hole locations into the bottom of the fender. Drill the mounting holes at 1/4″ diameter. Use the 6 x 16 mm counter-sunk fasteners and bezels for mounting the taillight

Incoming search terms:

KTM ELECTRICAL SYSTEMS INSTALLATION, REPAIR

0

Filed Under (KTM) by admin on 02-02-2012

download
DC SYSTEMS STEP DC1 – REGULATOR/RECTIFIER: PRE-2005 KTM If the stock regulator looks like below (the stock connector will not plug into the Trail Tech regulator/rectifier) then the provided stub connector must be soldered into the bike’s wire harness. For models without a stock battery, mount the reg/rec and plug the stub connector into it. Run the red and black wires directly to the (aftermarket) battery, and the yellow wires to the stator. SEE DC CIRCUIT DIAGRAM ON REVERSE SIDE OF PAGE. MODELS WITHOUT A STOCK BATTERY Move stock light to the DC circuit: divert lighting wire from AC circuit to DC circuit. In stock form, the lights are powered by the AC half of the electrical system. In order to continue to use the stock light, find the yellow wire (runs to stock headlight) shown below (wire bundles are found underneath gas tank) and cut the smaller gauge yellow wire. 1. Connect aftermarket light: Wire the light’s red(+) light lead to the positive(+) battery terminal, and the black(-) light lead to the negative(-) battery terminal. Trail Tech lights should use a 10-20 amp fuse as close to the positive(+) battery terminal as possible.

2000-2010 KTM X2 SWITCH WIRING HARNESS Removal and Installation Manual

0

Filed Under (KTM) by admin on 25-01-2012

download
The included 3600-SWHA switch harness is intended for use with offroad models that do not come with a Hi/Low beam switch from the factory. The harness is compatable with stock AC lighting electrical systems as well as high output DC electrical systems. 1. Remove the stock numberplate or headlight. Remove the stock kill switch from handlebars and replace with the 3600-SWHA switch. 2. Remove the gas tank. Route the white and black leads from the 3600-SWHA under the tank following the wires from the stock kill switch. Disconnect the stock kill switch bullet and connect the white wire of the 3600-SWHA to the wiring harness. Disconnect the stock kill switch ring terminal and connect the ring terminal of the 3600-SWHA. Fully remove the stock kill switch. Be sure all the wires are safe from being burned or pinched and re-install the gas tank. 3. Disconnect the two female spade terminals from the stock headlight switch (if present). Connect the terminal with the yellow wire to the red power lead from the switch. Connect the white wire to the blue accessory output from the switch. Be sure the clear silicone sleeves are covering the stock plastic housings. 4. Connect the X2 headlight to the switch headlight plug. Note: The stock headlight plug will not be used for the X2 installation, but is still functional for connecting the stock headlight. The stock plug will turn on and off with the new headlight switch, and will be powered in either of the Low or High Beam positions

Incoming search terms:

KTM EXC taillights Installation manual

0

Filed Under (KTM) by admin on 23-01-2012

download
Step1: Remove headlight, (headlight switch) seat and gas tank from KTM. Step 2: Partially install the headlight assembly using the top right band only to hold it in place temporarily. You will need to plug wires to this assembly and if you put all four bands on you will not be able to make the connections. Step 3: Install handlebar switch on clutch side. You will need to move clutch perch to the right (about ½ inch to1 inch) to make room for the switch. The red knob on the clutch adjuster should just miss the handlebar switch. The switch plugs into the circuit board on the bottom of the headlight using the 8-pin plug (the only unused 8-pin one on the circuit board) Step 4: Behind the gas tank and in front of the air box is a small rectangular hole in the frame. You will be feeding two lines with the plug ends first down through this hole. They must be fed one line at a time and you may need to use needle nose pliers to grab them and help pull them through. The lines you want to feed through this hole are the power line with two-pin molex plug and the line for the taillight with the six-pin plug. Route these wires all the way to the headlight assembly along the left side of the bike on the bottom of the gas tank frame tube. In this step we will connect the power line only. With the handlebars turned all the way to the right, plug the power wire into the back of the headlight assembly making sure to leave some extra wire so you can turn the handlebars both ways without tugging on the wires. The other end of the power line has battery terminal loops. The positive has an in-line fuse and the other black wire is the negative. Connect these to the battery.

YAMAHA YFM 350 Removing stock carburetor and cables.

0

Filed Under (Yamaha) by admin on 19-01-2012

download
Remove seat and gas tank. Make sure fuel petcock is in “off” position. 2. Remove throttle cable paying close attention to routing, as the new cable (s) will need too be routed the same. 3. Remove stock carburetor and stock throttle housing. Preparing motor for carburetor install 1. Remove stock manifold from cylinder head. 2. Place supplied o’ring into aluminum flange as pictured in figure 1. Figure 1. 3. Install aluminum and rubber flange to motor using supplied bolts. See Figure 2. The shorter 25mm bolt will need to be placed in the bottom hole. IMPORTANT NOTE: Install the aluminum flange with the o’ring towards the motor and the thick side up.

HARLEY DAVIDSON DETACHABLE WINDSHIELD AND DOCKING HARDWARE KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 05-02-2011

download
These kits fit 1984 and later FXST, FXSTB, FXSTC, and 1993 and later FXDWG model motorcycles when equipped with passing lamps. INSTALLATION 1. To protect against scratches, cover gas tank and front fender before installation. is 01985 Figure 1. New Clutch Cable Routing 2. For FXSTB Models: Proceed to Step 3. For all except FXSTB: See Figure 1. Relocate the clutch cable to the inside of the handlebars as follows: a. Locate cable adjuster halfway along clutch cable by the front frame downtube and slide off rubber boot. b. Holding cable adjuster with 1/2 inch wrench, loosen jam nut using a 9/16 inch wrench. Back jam nut away from cable adjuster. Move adjuster toward jam nut to introduce a large amount of free play at hand lever. c. Remove small snap ring from pivot pin groove at bottom of clutch lever bracket. Remove pivot pin and clutch hand lever from bracket. Remove anchor pin and clutch cable eyelet from clutch hand lever. d. See Figure 1. Route clutch cable to the inside of the handlebars and reconnect clutch cable to clutch lever. e. See Figure 2. Turn cable adjuster away from jam nut until slack is eliminated at hand lever. Pull clutch cable ferrule away from clutch lever bracket to check free play. Turn cable adjuster to obtain 1/16-1/8 inch (1.6- 3.2 mm) free play between end of cable ferrule and clutch lever bracket. f. Hold adjuster with 1/2 inch wrench. Using 9/16 inch wrench, tighten jam nut against cable adjuster. Cover cable adjuster mechanism with rubber boot

Incoming search terms: