HARLEY DAVIDSON CHROME BILLET LIFTER-COVER KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 25-02-2011

download
Installation with Stock Pushrods Refer to the service manual for your motorcycle model. Installation with Adjustable Pushrods Lifter-Cover Removal Installing or removing the pushrods with the valve train loaded can result in engine damage. On the cylinder being serviced, always set the lifters to the base circle on the cam before servicing pushrods, lifters, rocker arms, and valves. 1. Set the lifters of the rear cylinder to their lowest point, or base circle, on the cam. Refer to Setting the Lifters to the Base Circle in this instruction sheet. 2. See Figure 1. Insert a screwdriver into the slot on the side of the spring-cap retainer on the pushrod cover. 3. Press the spring-cap and retainer down while pulling outward to remove the spring-cap retainer. 4. See Figure 2. Lift the lower pushrod cover to reveal the lower third of the pushrod. 5. If the engine has stock pushrods installed and you are installing adjustable pushrods with this lifter-cover installation, go to step 6. If the engine already has adjustable pushrods installed and you are installing adjustable pushrods with this lifter-cover installation, go to step 7 6. Use a bolt cutter or similar tool to cut the stock pushrod. Avoid cutting the pushrods with a saw, grinder, or other method that may allow metal debris into the engine. Go to step 8. 7. Loosen the jam nut on each adjustable pushrod and resize each rod to its shortest length. 8. Remove the pushrod covers and pushrods from the engine. 9. Remove the O-rings from the seats in the engine at the top and bottom of the pushrod cover. 10. Remove the four screws fastening the lifter cover to the engine to remove the cover and gasket. 11. Remove old lifter-cover gasket material from the engine, taking care not to allow material to fall into the engine. Continue to Lifter-Cover Installation in this I-Sheet. Lifter-Cover Installation 1. See Figure 3. Verify that the lifter anti-rotation pin is in position. Installing or removing the pushrods with the valve train loaded can result in engine damage. On the cylinder being serviced, always set the lifters to the base circle on the cam before servicing pushrods, lifters, rocker arms, and valves. 2. Verify that the cylinder lifters are set to their lowest point, or base circle, on the cam. Refer to Setting the Lifters to the Base Circle in this instruction sheet. 3. Fasten the new lifter-cover gasket and chrome billet lifter cover to the engine using the chrome screws from this kit. In a cross pattern, torque the lifter-cover screws to 90 – 120 in-lbs (10.2 – 13.6 Nm). 4. See Figure 4. Loosen the jam nut on all of the pushrods and adjust the pushrods to their shortest length. NOTE See Figures 4 and 5. Install the narrow-band pushrods in the cylinder-intake location. Install the wide-band pushrods in the cylinder-exhaust location. 5. Assemble the O-rings (purchased separately) and pushrod covers. 6. Install the pushrods with the pushrod covers. The adjustment-end of the pushrod must be on the lifter

Incoming search terms:

DRAK AIR FILTER KIT INSTALLATION MANUAL

0

Filed Under (Tips and Review) by admin on 21-12-2010

download
1. Take off the Air fi lter cover by removing the Button head cap screw in the center. 2. Removed the fi lter element by taking out the three exposed Torx head cap screws. 3. Remove the breather hoses from the Cylinder head breather bolts by pulling on them. 4. Remove the three Bolts that secure the Backing plate to the Carburetor / Throttle body and the two Breather bolts that secure it to the Cylinder heads. 5. Remove the Backing plate and Gasket, on FI models the wiring mount clip should be carefully pulled out of the plastic housing. NOTE: Be sure that the gasket surface is clean and dry and that no gasket material remains stuck to it. 6. None of the OEM parts will be reused for this installation 1. For a clear understanding of this installation it is best to refer to the exploded view diagram while reading these instructions. 2. When installing or servicing the air cleaner, apply Loctite 243 (blue) to threads of all fasteners. 3. Loosely install the gasket (1) and carburetor / throttle body mount bracket (2) using the two cylinder head breather bolts (3) and cylinder head O-rings (4) NOTE: Make sure the gasket is installed in the correct rotation and right side up. The slightly smaller bleed hole should be in the top left hand corner. 4. Using the three 1/4″-20 x 1″ socket head cap screws (5) install the fi lter backing

2006 KAWASAKI KX450F Service Manual

0

Filed Under (Kawasaki) by admin on 16-12-2010

download
Tightening Torque Incorrect torque applied to a bolt, nut, or screw may lead to serious damage. Tighten fasteners to the specified torque using a good quality torque wrench. Often, the tightening sequence is followed twice-initial tightening and final tightening with torque wrench. Force Use commonsense during disassembly and assembly, excessive force can cause expensive or hard to repair damage. When necessary, remove screws that have anon -permanent locking agent applied using an impact driver. Use aplastic-faced mallet whenever tapping is necessary. Gasket, O-ring Hardening, shrinkage, or damage of both gaskets andO-rings after disassembly can reduce sealing performance. Remove old gaskets and clean the sealing surfaces thoroughly so that no gasket material or other material remains. Install new gaskets and replace used O-ringswhenre-assembling Liquid Gasket, Non-permanent Locking Agent For applications that require Liquid Gasket ora Non-permanent Locking agent, clean the surfaces so that no oil residue remains before applying liquid gasket or Non-permanent locking agent. Do not apply them excessively. Excessive application can clog oil passages and cause serious damage. Press For items such as bearings or oil seals that must be pressed into place, apply small amount of oil to the contact area. Be sure to maintain proper alignment and use smooth movements when installing

2006 KAWASAKI KX250F Service Manual

0

Filed Under (Kawasaki) by admin on 02-12-2010

download
Gasket, Oring Hardening, shrinkage, or damage of both gaskets andO-rings after disassembly can reduce sealing performance. Remove old gaskets and clean the sealing surfaces thoroughly so that no gasket material or other material remains. Install new gaskets and replace used O-ringswhenre-assembling Liquid Gasket, Locking Agent For applications that require Liquid Gasket ora Locking agent, clean the surfaces so that no oil residue remains before applying liquid gasket or locking agent. Do not apply them excessively. Excessive application can clog oil passages and cause serious damage. Press For items such as bearings or oil seals that must be pressed into place, apply small amount of oil to the contact area. Be sure to maintain proper alignment and use smooth movements when installing. GENERAL INFORMATION 1-5 Before Servicing Ball Bearingand Needle Bearing Do not remove pressed ball or needle unless removal is absolutely necessary. Replace with new ones whenever removed. Press bearings with the manufacturer and size marks facing out. Press the bearing into place by putting pressure on the correct bearing race as shown. Pressing the incorrect race can cause pressure between the inner and outer race and result in bearing damage. Oil Seal, Grease Seal Do not remove pressed oil or grease seals unless removal is necessary. Replace with new ones whenever removed. Press new oil seals with manufacture and size marks facing out. Make sure the seal is aligned properly when installing. Apply specified grease to the lip of seal before installing the seal.

Ducati 748 biposto specification

0

Filed Under (Ducati) by admin on 11-11-2010

download
part Number: G790-100-12A Description: Gasket Exhaust 4 Valve Belt product Details: Vee Two Gasket Sets are die cut from high quality gasket material and are supplied with ‘O’ Rings and Oil Seals. uoM: each Year from : all Year to : all part Number: V2-02-7307 Description: Main Bearing – Fits all 2 V + 4 V Belt to 2006 product Details: These bearings are carefully sourced from high end manufacturers and are supplied ro match the specific Bearing Clearances and fitting tolerances required for their particular requirements. uoM: each Year from : all Year to : all part Number: V2-03-604A Description: Camshaft – Road Drop In – Kit of 2 cams inlet only product Details: Drop in Street / Track camshaft, suited to predominately bigger bore 4 valve motors. Gives great bottom end feel due to increased torque. uoM: kit Year from : all Year to : all part Number: V2-03-606 Description: Camshaft – Track – Kit of 4 cams product Details: A predominately race bred camshaft made to produce horsepower at high revs. Very strong above 8500rpm. Must have a very high compression ratio motor, 13.5-1 minimum. uoM: kit Year from : all Year to : all

Harley-Davidson Evolution Engines S&S Billet Rocker Cover Assemblies Installation Instructions

0

Filed Under (Harley Davidson) by admin on 30-10-2010

download
1. Wash motorcycle, taking care to remove sand and other abrasive debris from engine and area of frame around engine. Remove battery, gas tanks, and all parts required to access original rocker covers. Remove top and center sections of rocker housings. Refer to authorized Harley-Davidson®Service Manual as necessary. Sparks from motorcycle electrical system can ignite gasoline fumes. To prevent sparks as well as prevent electric starter from becoming engaged inadvertently and causing personal injury, disconnect battery and remove from motorcycle before proceeding. Gasoline is toxic if fumes are inhaled, extremely flammable, and explosive under certain conditions. Do not smoke around gasoline, and perform installation in a well ventilated area away from sparks and open flame. 2. Remove pushrod cover retainer clips for front cylinder and collapse covers. Remove sparkplugs and rotate engine to place pushrods at lowest point on cam with front piston at TDC on compression stroke. Referring to Harley-Davidson®Service Manual as necessary, remove rocker assemblies, pushrods and lower rocker cover from front cylinder head. NOTE: Observe correct location of pushrods. S&S pushrod kits have longest pushrod for front exhaust, next longest for rear exhaust, shortest for rear intake, and remaining one for front intake. Remove all traces of old rocker housing gaskets from cylinder head, taking care to contain debris. Debris such as gasket material can interfere with oil circulation resulting in engine damage not covered under warranty. 3. Inspect S&S rocker cover assemblies. Remove rough or sharp edges from plain (unchromed) assemblies. Clean all metal parts with solvent. Dry with compressed air and remove any solvent residue with clean, lint free cloth. 3 CAUTION WARNING WARNING CAUTION 4. Install umbrella valves in rocker cover bases. See Picture 1. Valves go in vent ports nearest intake manifold on both front and rear rocker cover bases.

Harley-Davidson Twin Cam 88 S&S Billet Rocker Covers Installation Instructions

0

Filed Under (Harley Davidson) by admin on 30-10-2010

download
Failure to confirm pushrod/lifter placement before proceeding with installation can result in damage to rocker arm support plates and other parts. With pushrods at lowest point, front piston will be at TDC on Compression stroke. 4. Remove breather cover and baffle assembly. See Picture 2. 5. Remove rocker arm/rocker support plate. See Picture 3. NOTE – Gradually loosen rocker arm support bolts in following sequence (See Figure 1): 1. Left (driveside) rear 2. Right (camside) front 3. Right (camside) rear 4. Left (driveside) front Loosen bolts in sequence and in 1⁄ 4 -turnincrements for first 3⁄ 4 turn. Bolts can then be removed according to normal procedure. 6. Remove lower rocker housing bolts. NOTE – Gradually loosen lower rocker housing bolts in following sequence (See Figure 2): 1. Right (camside) front 2. Left (driveside) rear 3. Left (driveside) front 4. Right (camside) rear 5. Center front 6. Center rear Loosen bolts in sequence and in 1⁄ 4 -turn increments for first 3⁄ 4 turn. Bolts can then be removed according to normal procedure. 7. Remove lower rocker housing and gasket from head. Remove oil and any remaining gasket material from cylinder head gasket surface and clean gasket surface with lacquer thinner

Harley-Davidson Style Rocker Cover Assemblies installation Instructions

0

Filed Under (Harley Davidson) by admin on 27-10-2010

download
Installation 1. Wash motorcycle, taking care to remove sand and other abrasive debris from engine and area of frame around engine. Remove battery, gas tanks, and all parts required to access original rocker covers. Remove top and center sections of OEM rocker housings. Refer to authorized Harley-Davidson Service Manual as necessary. WARNING – Sparks from motorcycle electrical system can ignite gasoline fumes. To prevent sparks as well as prevent electric starter from becoming engaged inadvertently and causing personal injury, disconnect battery and remove from motorcycle before proceeding. WARNING – Gasoline is toxic when fumes inhaled, extremely flammable, and explosive under certain conditions. Do not smoke around gasoline, and perform installation in a well ventilated area away from sparks and open flame. 2. Remove pushrod cover retainer clips for front cylinder and collapse covers. Remove sparkplugs and rotate engine to place pushrods at lowest point on cam with front piston at TDC on compression stroke. Referring to Harley-Davidson Service Manual as necessary, remove rocker assemblies, pushrods and lower rocker cover from front cylinder head.
3 Picture 3 Picture 4 Right Left Rocker shaft reliefs must align with these holes. NOTE – Observe correct location of pushrods. S&S pushrod kits have longest pushrod for front exhaust, next longest for rear exhaust, shortest for rear intake, and remaining one for front intake. Remove all traces of old rocker housing gaskets from cylinder head, taking care to contain debris. CAUTION – Debris such as gasket material can interfere with oil circulation resulting in engine damage not covered under warranty. 3. Inspect S&S rocker cover assemblies. Remove rough or sharp edges from plain (unchromed) assemblies. Clean all metal parts with solvent. Dry with compressed air and remove any solvent residue with clean, lint free cloth. 4. Install umbrella valves in rocker cover bases. See Picture 1. Valves go in vent ports nearest intake manifold on both front and rear rocker cover bases.

Incoming search terms:

Incoming search terms: