Honda CG125 Owners Workshop Manual

0

Filed Under (Honda) by admin on 25-11-2010

download
Clean the air filter Pull off the right-hand side panel and remove the two nuts which secure the air filter cover. Withdraw the cover, checking that the sealing gasket is in good condition, pull out the retaining spring and withdraw the element assembly. Peel off the inner and outer foam sleeves. Wash all components in white spirit (Stoddard solvent) or in warm water and detergent and dry them thoroughly. Soak the foam sleeves in the specified oil, then squeeze them gently (do not wring them out or they will be damaged) to expel all surplus oil. Refit the sleeves to the element frame. On reassembly ensure that all components are correctly fitted so that unfiltered air cannot bypass the element. 2 Check the spark plug Remove the spark plug cap, unscrew the plug and check its condition, comparing it with the photographs on page 65. If it is badly worn or fouled it must be renewed. If it is fit for further service check the gap and reset it if necessary, as described in Chapter 3.8. 3 Check the valve clearances It is important that the correct valve clearance is maintained. A small amount of free play is designed into the valve train to allow for expansion of the various components. If the setting deviates greatly from that specified, a marked drop in performance will be evident. In the case of the clearance becoming too great, it will be found that valve operation will be noisy, and performance will drop off as a result of the valves not opening fully. If on the other hand, the clearance is too small the valves may not close completely. This will not only cause loss of compression, but will also cause the valves to burn out very quickly. In extreme cases, a valve head may strike the piston crown, causing extensive damage to the engine. The clearances should be checked and adjusted with a cold engine. Place the machine on its centre stand and remove the rocker cover, taking care not to damage the 0 ring. Remove the gearchange pedal and the left-hand outer cover to expose the generator rotor. Remove plug and allow old oil to drain Remove the spark plug, then slowly rotate the engine anticlockwise by way of the generator rotor, watching the inlet valve. When it has opened and closed again (sunk down and risen up to its original position), rotate the engine further until the T mark on the rotor periphery aligns exactly with the raised index mark which is positioned between 12 and 1 o’clock (from the crankshaft) on the generator stator. The engine will then be in the correct position for checking the valve clearances, namely at Top Dead Centre (TDC) on the compression stroke; check that there is free play at both rockers. Using a 0.08 mm (0.003 in) feeler gauge, check the clearance between the top of each valve stem and its corresponding rocker. The feeler gauge must be a light sliding fit, with the rocker and valve stem just nipping it. If necessary, slacken the locknut, and turn the small square-headed adjuster to obtain the correct setting. Tighten the locknut, holding the adjuster at the same time to prevent it from moving. Finally, recheck the setting and then repeat the procedure on the other rocker. 4 Check the contact breaker points and ignition timing Note: since the generator stator plate is located by its countersunk retaining screws, the ignition timing can only be altered by opening or closing the contact breaker gap; therefore both operations are described as one. The full procedure is given here for ease of reference, but if the points are found to be in good condition and if the gap has not altered or is within the tolerance, then the ignition timing will be sufficiently accurate and there will be no need to carry out the full check. First remove the gearchange pedal, the left-hand outer cover, the spark plug and the left-hand side panel

Harley-Davidson CHROME FRONT BRAKE CALIPER KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 25-11-2010

download
See Figure 1. Refer to FRONT BRAKE CALIPERS: REMOVAL in the Service Manual, and follow the instructions to: a. remove the banjo bolt with bleeder valve (2) and both gaskets (4), and b. detach the front brake line (3) from the caliper. c. Discard the gaskets. For this installation, the banjo bolt (2) can also be discarded. d. Remove the caliper mounting bolts (1). Lift the brake caliper assembly upward to remove it from the brake disc. -J03529 1 of 4
2 5 3 4 1 is04104 1. Mounting bolt (2) 2. Banjo bolt with bleeder valve 3. Brake line 4. Gasket (2) 5. Screen cover Figure 1. Remove Existing Caliper 2. Remove the brake pads from the caliper. Refer to BRAKE PADS AND DISCS: BRAKE PAD REPLACEMENT, FRONT BRAKE CALIPER in the Service Manual. a. Remove the screen cover (5) from the caliper. b. See Figure 2. Note the orientation of the brake pads, and remove the retaining clip (2), pad pin (1) and brake pads from the caliper. Also note the position of the brake pads at removal, so they can be installed back in the same location. 3. Repeat the procedure for the opposite-side caliper. 2 1 is04105 1. Pad pin 2. Retaining clip Figure 2. Front Caliper Pad Pin Pad and Pin Inspection 1. Refer to BRAKE PADS AND DISCS: INSPECTION in the Service Manual, and follow the instructions given to inspect the brake pads. If any front brake pad is worn to 0.5 mm (0.020 inch) or less above the backing plate, replace all four front pads. 2. Inspect the brake disc thickness, lateral runout and warpage. If necessary, follow the instructions in the Service Manual under FRONT WHEEL to replace the discs. Chrome Caliper Installation 1. See Figure 3. Obtain the correct-side new chrome caliper assembly from the kit. Remove the screen cover (5), retaining clip and pad pin (4) from the caliper. NOTE Do not remove the shipping plug protecting the brake line threaded hole until ready to install the brake line. 2. Place the caliper over the brake disc with the brake line threaded hole (protected by a shipping plug) facing upward. 3. See Figure 1. Obtain two of the brake caliper mounting bolts (1), removed earlier. Loosely install both bolts through the front fork and into the chrome caliper. Alternately tighten the mounting bolts to 38.0-51.5 Nm (28-38 ft-lbs) . 4. Install the brake pads removed earlier or, if necessary, new brake pads into the caliper. 5. See Figure 2. Install the new pad pin (1) through the inner and outer brake pads. Tighten to 8.5-11.5 Nm (75-100 in- lbs ) . 6. Install the new retaining clip (2) onto the pad pin. NOTE Ensure that the screen cover is oriented with the single tab end up, and the double tab end down. 7. See Figure 1. Install the new screen cover (5) onto the caliper.

Incoming search terms:

1999 Yamaha XVS1100 (L) DragStar Service Manual

0

Filed Under (Yamaha) by admin on 21-11-2010

download
PREPARATION FOR REMOVAL PROCE- DURES 1. Remove all dirt, mud, dust and foreign material before removal and disassembly. 2. Use proper tools and cleaning equipment. Refer to the “SPECIAL TOOLS” section. 3. When disassembling the machine, always keep mated parts together. This includes gears, cylinders, pistons and other parts that have been “mated” through normal wear. Mated parts must always be reused or replaced as an assembly. 4. During machine disassembly, clean all parts and place them in trays in the order of disassembly. This will speed up assembly and allow for the correct installation of all parts. 5. Keep all parts away from any source of fire GASKETS, OIL SEALS AND O-RINGS 1. Replace all gaskets, seals and O-rings when overhauling the engine. All gasket surfaces, oil seal lips and O-rings must be cleaned. 2. Properly oil all mating parts and bearings during reassembly. Apply grease to the oil seal lips LOCK WASHERS/PLATES AND COTTER PINS 1. Replace all lock washers/plates 1 and cotter pins after removal. Bend lock tabs along the bolt or nut flats after the bolt or nut has been tightened to specification. EB101040 BEARINGS AND OIL SEALS 1. Install bearings and oil seals so that the manufacturer’s marks or numbers are visible. When installing oil seals, apply a light coating of lightweight lithium base grease to the seal lips. Oil bearings liberally when installing, if appropriate. 1 Oil seal

Ducati 748 biposto specification

0

Filed Under (Ducati) by admin on 11-11-2010

download
part Number: G790-100-12A Description: Gasket Exhaust 4 Valve Belt product Details: Vee Two Gasket Sets are die cut from high quality gasket material and are supplied with ‘O’ Rings and Oil Seals. uoM: each Year from : all Year to : all part Number: V2-02-7307 Description: Main Bearing – Fits all 2 V + 4 V Belt to 2006 product Details: These bearings are carefully sourced from high end manufacturers and are supplied ro match the specific Bearing Clearances and fitting tolerances required for their particular requirements. uoM: each Year from : all Year to : all part Number: V2-03-604A Description: Camshaft – Road Drop In – Kit of 2 cams inlet only product Details: Drop in Street / Track camshaft, suited to predominately bigger bore 4 valve motors. Gives great bottom end feel due to increased torque. uoM: kit Year from : all Year to : all part Number: V2-03-606 Description: Camshaft – Track – Kit of 4 cams product Details: A predominately race bred camshaft made to produce horsepower at high revs. Very strong above 8500rpm. Must have a very high compression ratio motor, 13.5-1 minimum. uoM: kit Year from : all Year to : all

Mikuni Carburetor Rebuild

0

Filed Under (Mikuni) by admin on 31-10-2010

download
1.1 (Below) First note the position of both your high and low speed screws (some models also have a midrange screw). Use a screwdriver to lightly set the screw, noting how many turns in it takes. NOTE: Some Sea-Doos may be seated fully (zero turns) to begin with; do not force the screws. After noting the screw positions, remove the screws. 1.2 Remove the center screw, fuel inlet and o-ring. 1.3 (Below) Remove the six screws securing the pump cover and remove it. 1.4 (Below) Remove the check valve diaphragm. 1.5 (Below) Remove the pump body. 1.6 (Below) Remove the regulator cover and clean the gasket off from it.

Victory Freedom Engines Installation Instructions for S&S Air Cleaner Kit

0

Filed Under (Victory) by admin on 31-10-2010

download
1-Locate and remove the Intake Air Temperature Sensor (IATS) from the stock Polaris Victory air box. Locate the new position for the IATS on the bottom of the S&S air cleaner. Push the IATS in the lower air cleaner cover and turn1⁄ 4 turnin either direction, make sure you feel it lock into place. Inspect from the inside of the air cleaner to ensure that the barbs are locked into place. See Picture 1. 2-Using the stock Polaris Victory air box gasket (PN 5811908) and S&S supplied (Qty 4) M6 fasteners, assemble the lower air cleaner cover to the throttle body using 243 Blue Loctite®on the treads. Torque the M6 fasteners to 72-96 inch pounds. 3-Position the S&S pre-formed air filter onto the lower air cleaner cover ensuring that it fits into the machined groove. 4-Install the top air cleaner cover on top of the filter ensuring that it fits into the machined groove. 5-Make surethat the filter is situated in the machined grooves on both the top and bottom air cleaner covers. 6-Using 243 Blue Loctite on the threads of the S&S supplied (Qty 3) M6 fasteners tighten down top air cleaner cover evenly until seated. Finish torque the fasteners to 72-96 inch pounds. Now you’re ready for breather hose and barometric pressure hose routing. 7-Locate the S&S supplied 3⁄ 16 “reinforced hose and clamps. Push one end of the hose on the 3⁄ 16 “brass barb in the bottom air cleaner cover and slide clamp up around the end of the hose. The other end of the hose is for the Barometric Pressure Sensor (MAP). Route the hose towardthe back of the engine over the top of the rear rocker cover. 8-Remove the MAP sensor from the stock Polaris Victory air box. Remove the orange rubber gasket from the MAP sensor. Slide the S&S supplied clamp over the 3⁄ 16 “rubber hose that leads to the air cleaner. Push the barbed end of the MAP sensor into the 3⁄ 16 ” rubber hose and slide clamp up to the end of the hose around the barb. A small amount of lubricant may be applied to the barb on the MAP sensor to make installation easier. 2 S&S Air Cleaner Assembly 41-0021 (Calibration cardnot shown) Picture 1 CAUTION WARNING WARNING Plastic barb locked in recess.
9-Assemble and install breather hose as follows: A-Cut the stock Victory®hose on the straight section just behind the 90 degree bend as shown in Picture 2 . B-Slide an S&S supplied 1⁄ 2 “hose clamp over the modified stock breather hose. C-Install the S&S straight barb in Victory breather hose and position a hose clamp around hose end. D-Slide the 90-degree end of breather hose over the brass barb on the air cleaner cover and slide hose clamp in place. E-Position straight end of the S&S breather hose over the 1⁄ 2 “barb to connect to the Victory hose. Slide clamp over connection. F- See Pictures 3 and 4 for breather hose and barometric pressuresensor hose installation positions. NOTE: S&S breather hose can be cut for best fit

Incoming search terms:

ROAD TECH ZUMO 660 GLOBAL POSITIONING SYSTEM (GPS) FAIRING MOUNTING KIT INSTALLATION

0

Filed Under (Tips and Review) by admin on 27-10-2010

download
1. Refer to the service manual and follow the instructions given to remove the main fuse. 2. Remove the outer fairing and windshield. Refer to the service manual. is05900 Figure 1. Road Tech Zumo Drilling Template Placement 3. See Figure 1. Obtain the drilling template from the kit. 4. Position the template on the back side of the inner fairing, in the upper left corner above the fuel gauge, aligning the template to the top of the inner fairing and the plastic rib as shown. 5. Drill a 5/16 inch (8 mm) diameter hole through the inner fairing per the template. 6. See Figure 4. Position the gasket (2) and GPS mount (1) onto the face of the inner fairing, aligning the upper hole in the mount with the hole drilled in the previous step. 7. Temporarily install one of the screws (4) through the upper hole to help align the GPS mount. 8. See Figure 2. Mark the location of the lower mounting hole on the face of the inner fairing, using the GPS mount and gasket as a template. Mark the location of the wire routing hole using the guide hole (3) in the gasket as a template. 9. Remove the screw, GPS mount and gasket from the inner fairing. 10. Drill a 5/16 inch (8 mm) diameter hole through the inner fairing in the lower mounting location. Drill an 11/16 (17 mm) diameter hole through the inner fairing in the wire routing location. 1 2 3 is06149 1. Gasket 2. Wire routing guide hole and ribs 3. Guide hole Figure 2. Remove Gasket Ribs and Guide Hole 11. See Figure 2. Remove the wire routing guide hole and four ribs (2) from the gasket (1). 12. See Figure 4. Install the GPS mount and gasket to the inner fairing with screws (4) flat washers (5) and locknuts (6). Tighten to 50-60 in-lbs (5.6-6.8 Nm) 13. Obtain cradle with harness from GPS system kit. NOTE The fuse holder on the harness must be opened to fit through the hole. 14. Insert harness through the 11/16 inch (17 mm) diameter hole drilled earlier. 15. Insert the split grommet into the 11/16 inch (17 mm) diameter hole around the harness. Installing the Cradle 1. See Figure 4. Install four bushings (H) from the GPS system kit and insert them into the back of the cradle mounting holes. 2. Position the cradle to the GPS mount. Direct the harness out through the slot (G) of the mount. 3. Insert a button head screw (3) through one of the holes in the cradle and into the corresponding hole in the GPS mount, but do not fully tighten

Incoming search terms:

1969-1978 BMW Motorrads LED Blinker Conversion Kit Installation Instructions

0

Filed Under (BMW) by admin on 26-10-2010

download
Disassemble all 4 blinker light assemblies as shown in Figure 2 to start the installation. Be sure to remove the lens, gasket, and bulb/reflector assembly completely. Be sure to remove the wires from the reflector assembly prior to removal from the housing. The reflector assembly will not be used any further, keep in a safe place to be stored, if desired. Figure 3 2. Figure 3 (left) shows the function with their labels on the screw terminal block locations. If planning to use the “Running Light” feature, an additional wire might be needed to be installed to use this option. If you desire to use the “Running Light” function of these LED Boards, please refer to section “How to Use the Running Light Feature of the CD1007s”for complete instructions. 3. Pull out the existing wires far enough so that they can easily reach the terminal block. Insert the correct wire in the correct location of the terminal block. Using a jeweler flat-blade screwdriver, tighten the screw to secure the wire in its location. It is highly recommend to keep the terminal block to end of the signal housing facing outward of the motorcycle, as illustrated in Figure 3 (right). Model: CD1007, LED Blinker Conversion Kit Installation Instructions For 1969-1978 BMW Motorrads: Disclaimer: Under no circumstances will Bulbsthatlast4ever or it’s representatives be responsible or liable for any incidental or consequential property damages or personal injuries arising from or in connection with the use or installation of any of the listed foregoing products or devices. Rev. 6/10 Figure 4 4. Install the screws into the lens, then place an o-ring over each screw, as illustrated in Figure 4 (left & right). The o-rings will prevent the LED Board from moving around due to vibration

Incoming search terms:

KYMCO Super 8 150 Exhaust System with M-2 Canister Installation Instructions

0

Filed Under (Kymco) by admin on 26-10-2010

download
1.*Make*sure*the*bike*is*completely*cool*before*starting* the*installation.*Make*sure*the*bike*is*secure*on*a* centerstand*or*ideally*a*service*lift. 2.*Remove*OEM*exhaust*assembly. 3.*Attach*supplied*muffler*hanger*bracket*using*the* supplied*flange*bolts*and*tighten*to*15lbs-ft. 4.*Attach*TBR*header*to*muffler*using*the*X-ring*and*4* 6x14mm*bolts*with*lock*washers*provided,*leave*loose* for*now. 5.*Install*TBR*exhaust*to*scooter*keeping*the*OEM*exhaust* gasket*between*header*and*cylinder*head. 6.*Slide*rubber*lined*muffler*clamp*over*muffler*assembly* and*secure*to*bracket*using*supplied*8x20mm*bolt*and* nut. 7 .*Check*muffler*alignment*and*tighten*header*nuts*then* X-ring*bolts*and*finally*muffler*clamp*bolt. 8.*Before*you*run*the*bike,*clean*off*all*fingerprints*and* dirt,*as*any*oily*residue*will*etch*the*metal*and*become* somewhat*permanent*when*the*system*gets*hot.*Run* the*bike*and*enjoy.*It*is*normal*for*some*white*smoke*to* appear*the*first*time*you*start*the*bike.*This*is*packing/ manufacturing*oil*from*inside*the*pipe*burning*off.* Check*for*gaps*or*leaks.*If*you*find*a*leak,*a*little*high* temperature*silicon*sealant*should*fix*it.*After*50*to*100* miles,*recheck*all*fasteners*for*tightness. Qty.*Description* Part*Number 1* Muffler*Canister*M-2** Varies 1* Header* 005-27401H 1* Muffler*Clamp* Varies 1* HARDWARE*KIT* 005-274-3 2* *X-Ring* (half)* 005-7-2-3 1* *Long*Muffler*Mounting*Bracket* 005-274-B 1* *8mm*Flange*Nut* 005-FN8

APRILIA SPORTCITY 250/ 200/ 125 STREET LEGAL EXHAUST SYSTEM Installation instructions

0

Filed Under (Aprilia) by admin on 26-10-2010

download
1. Put the motorcycle on a central stand. Make sure, that surface is solid and flat. 2. Unscrew the bolt from the metal clamp at the muffler – collector joint, all muffler brackets and remove the muffler (Figure 1, 2, 3, 4). T-handle 10mm wrench T-handle 12mm wrench T-handle 13mm wrench T-handle 5mm three hexagon key wrench Spring puller Figure 1 Figure 2 Figure 3 Figure 4
NAV – 333 3 INSTALLATION OF THE AKRAPOVIC SLIP-ON EXHAUST SYSTEM: 1. Insert the graphite gasket into the inlet bush of the link-pipe and correctly attach the metal clamp on the inlet bush of the link-pipe (Figure 5, 6). Slide the link pipe onto the stock collector (Figure 7, 8). Insert the catalytic converter into the link- pipe as shown (Figure 9, 10). Figure 5 Figure 6 Figure 7 Figure 8 Figure 9 Figure 10 NAV – 333 4 Figure 15 Figure 16 2. Slide the muffler onto the link-pipe and attach the springs (Figure 11, 12). Correctlyassemble the bolt, washer and aluminium distance bushe (Figure 13, 14). Tighten the bolts of muffler bracket and metal clamp (Figure 15, 16). 5.9Nm 4.3 ftlb 21Nm 15ftlb Figure 11 Figure 12 Figure 13 Figure 14 NAV – 333 5 final installation: 1. Clean grease spots: a. Muffler – titanium outer sleeve: use a soft cloth sprayed with a multi-purpose spray lubricant (WD-40 or equivalent). b. Carbon-fiber outlet cap: use a soft dry cloth. c. Stainless steel link pipe: use a soft cloth sprayed with a contact cleaner, then wipe with a soft dry cloth Cleaning will prevent spots from burning onto the surface. Do not use aggressive chemical cleaners, because they can damage the sticker.