Harley-Davidson Six Speed Transmissions FLH 2009 Up Champion Reverse Gear Installation Instructions

0

Filed Under (Harley Davidson) by admin on 17-02-2011

download
Preparation Remove Original Parts From Vehicle. 2.1 Purchase a small tube of Loctite #262 (red) for use later. 2.2 To torque the large gear: 2.2.1 Purchase Snap-On (or equivalent) filter tool. Part #: FWA62121. OR 2.2.2 Purchase Champion special tool – Part # RG-100-100 2.3 Drain the transmission oil. 2.4 Remove front and rear exhaust header pipe. 2.5 Remove the clutch release cover (right side). 2.6 Remove throw out bearing assembly. (to be reinstalled later without modification) 2.7 Remove the two nuts from the main and counter transmission shafts. WARNING : Do not attempt to push shafts into gearbox or remove the trap door – This can cause spacers inside the gearbox to be miss-aligned and lock up the gearbox when gears are installed and tightened. 2.8 Remove clutch push rod (to be replaced w/ Champion supplied rod) Note: For hydraulic clutch bikes, obtain Champion Part # RG-100-082, a longer push rod) Snap-On Part No: FWA62121 Snap-On Part No: FWA62121 Champion Part No: RG-100-100 Reverse Gear Installation Instructions Harley-Davidson Six Speed Transmission HD FLH 2009 Up Page 3 of 5 Revision 2 Boring Tool 3 Installation 3.1 Thoroughly clean threads of main and counter shafts using a silicon remover. 3.2 Apply the green thread locking compound (supplied) to main shaft threads and screw the small gear onto the main shaft. Figure 1 3.3 Install the supplied (ear)plug into the main shaft hole. To be removed later. 3.4 Install the supplied special tool to the small gear. Ensure the holes of the special tool align with the holes in the small gear. Figure 2 3.5 Install torque wrench to special tool and torque the small gear to 80 lb. ft. 3.6 Remove torque wrench from special tool. Do not remove special tool from small gear. 3.7 Using the supplied boring tool and the special tool as a guide, drill the main shaft through two holes of the special tool as shown. Stop when cutter contacts bearing race. Figure 3 3.8 Remove special tool, leaving main shaft plug in place, and thoroughly clean out the holes. Use care to ensure debris does not enter transmission. 3.9 Remove plug from main shaft hole. Figure 1 Figure 2 Figure 3 Note: To prevent gears from rotating during torque procedures, engage transmission into 1st gear and apply brakes Note: Frequently stop cutting and remove bit from hole to clean bit and vacuum debris from hole

Incoming search terms:

Harley-Davidson Six Speed Transmissions Reverse Gear Installation Manual

0

Filed Under (Harley Davidson) by admin on 16-02-2011

download
Remove Original Parts From Vehicle. 2.1 Purchase a small tube of Loctite #262 (red) for use later. 2.2 To torque the large gear: 2.2.1 Purchase Snap-On (or equivalent) filter tool. Part #: FWA62121. OR 2.2.2 Purchase Champion special tool – Part # RG-100-100 2.3 Drain the transmission oil. 2.4 Remove front and rear exhaust header pipe. 2.5 Remove the exhaust pipe support bracket. 2.6 Remove the clutch release cover (right side). 2.7 Remove throw out bearing assembly. (to be reinstalled later without modification) 2.8 Remove the two nuts from the main and counter transmission shafts. WARNING : Do not attempt to push shafts into gearbox or remove the trap door – This can cause spacers inside the gearbox to be miss-aligned and lock up the gearbox when gears are installed and tightened. 2.9 Remove clutch push rod (to be replaced w/ Champion supplied rod) Note: For hydraulic clutch bikes, obtain Champion Part # RG-100-082, a longer push rod) Installation 3.1 Reinstall exhaust pipe support bracket with the supplied two 5/16-18 x 1 3/4″ long hex head bolts and the ¼” thick spacer between engine and bracket. Figure 1 3.2 Thoroughly clean threads of main and counter shafts using a silicon remover. 3.3 Apply the green thread locking compound (supplied) to main shaft threads and screw the small gear onto the main shaft. Figure 2 3.4 Install the supplied plug into the main shaft hole. To be removed later. 3.5 Install the supplied special tool to the small gear. Ensure the holes of the special tool align with the holes in the small gear. Figure 3 3.6 Install torque wrench to special tool and torque the small gear to 80 lb. ft. 3.7 Remove torque wrench from special tool. Do not remove special tool from small gear

Wangye WY250T SPECIFICATION AND USER MANUAL

0

Filed Under (Wangye) by admin on 25-11-2010

download
item Data Item Data L×W×H mm 2015×680×1210 Front Tyre T 130/160-13 Wheelbase mm 1350 Rear Tyre 110/180-10 Ground Clearance mm 101 Air Pressure of Fr tyre 200 kPa Dry weight kg 160kg Air Pressure of Rr tyre 250 kPa Max Load kg 150kg Transmission system CVT Turning angle of steering handle ≤48° Ratio 5.12~15.05 Brake base mm ≤7(30km/h) Engine Type 169MM Single Cylinder、4 stroke、 water-cooled Max Speed km/h ≥85km/h Bore×stroke mm 69×66.8 Consumption L/100km ≤3.1L/100km Displacement ml 249.8 Climb ability º ≥18 Clutch automatically centrifugal Light vertical angle -1.3% Fuel tank L 7 Starting system Electric Battery 12V 9Ah – 4 – Table 2 Item specification Item Specification Lubricative System Press & splash Ignition System CDI Rated Power 10.5kW/6500(r/min) Fuse 15 A Max Torque 17.6N.m/5000(r/min) Front light 12V 35W/35W×2 Compression ratio 10.01 ∶ Tail/stop light 12V P21/5W Spark Plug Model DPR7EA(NGK) 、D7RTC或DPR6EA License light 12V 5W Spark plug gap mm 0.6~0.7 mm Turning light 12V 10W×4 Gap of valve 0.1(cold) Fuel RQ90 above Idling speed (1500±150)r/min Gearbox oil SAE 80W/90 Engine oil SF SAE 10W/40 capacity of gear box 0.18L Capacity of engine oil 1.1L

Incoming search terms:

2008 KTM Model Engine Oil Recommendation Chart

0

Filed Under (KTM) by admin on 24-11-2010

download
2008 Model Type Recommended Engine Oil Type Quantity SPORTMINICYCLES AC 50 SX MINI Motorex ATF Super (Dexron II Gear Oil) 0.15-0.2 L SPORTMINICYCLES LC 50 SX JUNIOR Motorex ATF Super (Dexron II Gear Oil) 0.15-0.2 L 50 SX Motorex ATF Super (Dexron II Gear Oil) 0.15-0.2 L 65 SX Motorex Top Speed 4T 15W50 0.5L SX 2 STROKE 85 SX Motorex Top Speed 4T 15W50 0.5 L 105 SX Motorex Top Speed 4T 15W50 0.5 L 125 SX Motorex Top Speed 4T 15W50 0.7 L 144 SX Motorex Top Speed 4T 15W50 0.7 L 250 SX Motorex Top Speed 4T 15W50 0.7 L SX 4 STROKE 250 SX-F Motorex Power Synt 4T 10W50 1.1 L 450 SX-F Motorex Power Synt 4T 10W50 1.35 L 505 SX-F Motorex Power Synt 4T 10W50 1.35 L CROSS COUNTRY 2 STROKE 65 XC Motorex Top Speed 4T 15W50 0.5L 85 XC Motorex Top Speed 4T 15W50 0.5L 105 XC Motorex Top Speed 4T 15W50 0.5 L 200 XC Motorex Top Speed 4T 15W50 0.7 L
200 XC-W Motorex Top Speed 4T 15W50 0.7 L 250 XC Motorex Top Speed 4T 15W50 0.7 L 250 XC-W (e) Motorex Top Speed 4T 15W50 0.7 L 300 XC Motorex Top Speed 4T 15W50 0.7 L 300 XC-W (e) Motorex Top Speed 4T 15W50 0.7 L CROSS COUNTRY 4 STROKE 250 XC-F Motorex Power Synt 4T 10W50 1.1 L 250 XC-F-W Motorex Power Synt 4T 10W50 1.1 L 450 XC-F Motorex Power Synt 4T 10W50 1.35 L 450 XC-W (R) Engine – Motorex Power Synt 4T 10W50 Gearbox – Motorex 4T 10W50 0.7 L 0.9 L 505 XC-F Motorex Power Synt 4T 10W50 1.35 L 530 XC-W (R) Engine – Motorex Power Synt 4T 10W50 Gearbox – Motorex 4T 10W50 0.7 L 0.9 L ENDURO RACING 450 EXC (R) Engine – Motorex Power Synt 4T 10W50 Gearbox – Motorex 4T 10W50 0.7 L 0.9 L 530 EXC (R) Engine – Motorex Power Synt 4T 10W50 Gearbox – Motorex 4T 10W50 0.7 L 0.9 L SUPERMOTO LC4 690 Supermoto Motorex Power Synt 4T 10W60 Approx. 2.0 L SPORT ATV 450 XC Motorex Power Synt 4T 10W50 2.0 L 525 XC Motorex Power Synt 4T 10W50 2.0 L LC8 950 Super Enduro (R) Motorex Power Synt 4T SAE 10W50 (for temperatures over 32° F) and 5W40 (for temperatures under 32° F) Approx. 3.0 L 990 Adventure Orange Motorex Power Synt 4T SAE 10W50 (for temperatures over 32° F) and 5W40 (for temperatures under 32° F) Approx. 3.0 L 990 Adventure Black Motorex Power Synt 4T SAE 10W50 (for temperatures over 32° F) and 5W40 (for temperatures under 32° F) Approx. 3.0 L 990 Adventure S Motorex Power Synt 4T SAE 10W50 (for temperatures over 32° F) and 5W40 (for temperatures under 32° F) Approx. 3.0 L 990 Super Duke Motorex Power Synt 4T SAE 10W50 (for temperatures over 32° F) and 5W40 (for temperatures under 32° F) Approx. 3.0 L 990 Super Duke R Motorex Power Synt 4T SAE 10W50 (for temperatures over 32° F) and 5W40 (for temperatures under 32° F) Approx. 3.0 L

Incoming search terms:

BMW R65 Monolever Specifications

0

Filed Under (BMW) by admin on 23-11-2010

download
Engine Motor Type Bore x Stroke Displacement Max Power Max Torque Compression Ratio Valves Per Cylinder Valve Control Carburation System Engine Lubricating System Power Transmission Clutch Number of Gears ear Selection Gearbox Ratios Rear Wheel Ratio Bevel/Crownwheel Electrical System Ignition System Alternator Starter
Spark Plugs Four-stroke two cylinder horizontally opposed “Boxer” engine, air cooled 82 x 61.5 mm (3.22 x 2.42 in)
649.6 cc 48 hp (35 KW) at 7,250 rpm or 27 hp (20 Kw) at 5500 rpm 47.8 Nm / 35 ft lb at 3,500 rpm or 45.5 Nm / 33 ft lb at 3,500 rpm 8.7 : 1 or 8.4 : 1 2 OHV, using push rod and rocker arm 2 constant depression carburettors, Bing
64/32/359 – 64/32/360 or 64/26/317 – 64/26/318 Wet sump Dry single plate, with lever action diaphragm spring
5 Dog type gearbox (ratchet foot lever) 4.4 / 2.86 / 2.07 / 1.67 / 1.50

Rokon Motorcycle Trail-Breaker SPECIFICATION

0

Filed Under (Rokon) by admin on 23-11-2010

Model: Rokon Trail-Breaker
Engine and transmission
Displacement: 172.00 ccm (10.50 cubic inches)
Engine type: Single cylinder, four-stroke
Power: 6.60 HP (4.8 kW)) @ 4000 RPM
Fuel system: Carburettor
Ignition: Electronic Magneto
Cooling system: Liquid
Gearbox: 3-speed
Fuel consumption: 0.45 litres/100 km (222.2 km/l or 522.71 mpg)
Greenhouse gases: 10.4 CO2 g/km. (CO2 – Carbon dioxide emission)
Exhaust system: Muffler with US Forestry approved spark arrestor
Chassis, suspension, brakes and wheels
Front tyre dimensions: 5.90-15
Rear tyre dimensions: 5.90-15
Front brakes: Single disc
Rear brakes: Single disc
Physical measures and capacities
Dry weight: 94.3 kg (208.0 pounds)
Power/weight ratio: 0.0700 HP/kg
Overall height: 762 mm (30.0 inches)
Overall length: 2,007 mm (79.0 inches)
Overall width: 787 mm (31.0 inches)
Ground clearance: 381 mm (15.0 inches)
Wheelbase: 1,295 mm (51.0 inches)
Fuel capacity: 10.18 litres (2.69 gallons)

Incoming search terms:

BMW F650 CS Front belt wheel not correctly secured

0

Filed Under (BMW) by admin on 23-11-2010

download
2.1 Removal of the front belt wheel Remove the front belt wheel in accordance with the instructions detailed in the F 650 CS Repair Manual. Remove the securing screw of the activated charcoal filter and let the filter canister hang by one side by the hoses, or remove it and lay it aside. Clean the splines and threads of the main shaft in order to remove all traces of Loctite. If necessary, remove corrosion from the main shaft spline (use only a brass bristle brush). 2.2 Visual inspection Check the splines of the main shaft for damage. Replace the main shaft if the splines are damaged (broken, chipped, bent or damaged teeth). Refer to the F 650 CS Repair Manual for this procedure 2.3 Wear check gearbox main shaft- It is extremely important that the techni- cian always check that the dimensions of the gearbox main shaft splines are to specification before proceeding with the installation of a new front belt wheel. This note only applies to motorcycles with accumulated mileage, not to new motorcycles from the crate. If the visual inspection was satisfactory and the main shaft was not replaced for visual damage, a main shaft wear check will be necessary. This check requires the use of BMW Special Tool # 23 4 571 . The adapters are designed for micrometer gauges with stud diameters from 6.35 mm to 6.6 mm. Do not use cellulose-lacquer thinners to clean the adapters as there is a risk of damaging the measuring instruments. Make sure that the micrometer gauges and the adapters are perfectly clean

Moto Guzzi Breva V1100 Repair Manual

0

Filed Under (Moto Guzzi) by admin on 18-11-2010

download
1.2. GENERAL RULES 1.2.1. BASIC SAFETY RULES CARBON MONOXIDE When an operation must be performed with the engine running, position the motorcycle outdoors in a well-ventilated area. Never run the engine in an enclosed place. Use an exhaust emission extraction system when working indoors. DANGER Exhaust gases contain carbon monoxide, a poisonous gas which, if inhaled, may cause loss of consciousness or even death. FUEL DANGER The fuel used to operate engines is highly flammable and becomes explosive under particular conditions. Refueling and maintenance operations should be carried out in a well-ventilated area, with the engine off. Do not smoke when refueling or in the proximity of sources of fuel vapors. Avoid contact with bare flames, sources of sparks and any other source which may ignite fuel or lead to explosion. DO NOT DISPOSE OF FUEL IN THE ENVIRONMENT. KEEP AWAY FROM CHILDREN. HOT COMPONENT PARTS The engine and exhaust component parts become hot when the engine is running and will stay hot for some time after the engine has been stopped. Wear insulating gloves before handling these components or allow for the engine and the exhaust system to cool down before proceeding. USED GEARBOX AND FORK FLUIDS DANGER Wear latex gloves when servicing. Prolonged or repeated contact with gear fluid may cause severe skin damage. Wash your hands thoroughly after handling. Dispose of it through the nearest waste oil reclamation firm or through the supplier. Wear latex gloves when servicing. DO NOT DISPOSE OF FLUID IN THE ENVIRONMENT. KEEP AWAY FROM CHILDREN. BRAKE FLUID WARNING Brake fluid can damage plastic, rubber or painted parts. When servicing the brake system, protect all such parts with a clean cloth. Always wear safety glasses when servicing the brake system. Brake fluid is highly irritant. Avoid contact with the eyes. In case of contact with the eyes, rinse abundantly with cool, clean water and immediately seek medical attention. KEEP AWAY FROM CHILDREN

Incoming search terms:

BMW K 1300 S, K 1300 R and K 1300 GT SPECIFICATION

0

Filed Under (BMW) by admin on 17-11-2010

download
The K 1300 S with 175 hp, the K 1300 R with 173 hp and the K 1300 GT with 160 hp. The new K bikes feature updated transmission and clutch assembly, plus smoother engine performance and new switchgear. Von Kuenheim continues: “By raising capacity to 1300 cc, our engineers have not only increased output but also torque on all three models. At the same time the driveline was intensively revised from air/fuel mixture formation right through to the exhaust system. In this way we have been able to optimize partial load behavior as well as throttle response. Now the clutch can be operated with even less effort and with greater refinement. Shifting has been improved tangibly due to constructional changes to the gearbox and drive.” BMW is introducing new options for the 2009 as well. The popular Electronic Suspension Adjustment that first appeared on the 2005 K 1200 S has now been updated with even more on-the-fly adjustability and it’s called ESA II. Also new is the quick-shifter option, racing-style gear shift assistant, borrowed from BMW’s race-ready HP2 Sport. Automatic Stability Control (ASC) is also offered as an option on the new K bikes. “Both the K 1300 S and also the R will also have the shift assistant – familiar from the HP2 Sport – available as an option for the first time,” von Kuenheim emphasized. “We have also advanced the chassis. The new lower longitudinal strut is now made of aluminum and is thus considerably lighter. This makes the front wheel guidance response even more sensitive. The result of this comprehensive development work is superior handling, improved rideability and lower fuel consumption. The electronically adjustable suspension – called ESA in short – was launched as a world first on the K 1200 S. Now we are presenting the new, well-proven ESA II as an option for the K Series. Apart from the suspension and damping this unique system also allows the spring rate to be adjusted at the press of a button. The K Series model revision also heralds a new and innovative generation of switches and controls.

Incoming search terms:

ATK 450 MX SPECIFICATIONS

0

Filed Under (Atk) by admin on 16-11-2010

Model: ATK 450 MX Year: 2008 Category: Enduro / Engine and transmission Displacement: 449.00 ccm (27.40 cubic inches) Engine type: Single cylinder, four-stroke Power: 48.00 HP (35.0 kW)) @ 10000 RPM Compression: 12.3:1 Bore x stroke: 95.0 x 63.4 mm (3.7 x 2.5 inches) Fuel system: njection. EFI Fuel Injection Fuel control: DOHC Ignition: 12v Battery w Constant Energy Inductive Coil Cooling system: Liquid Gearbox: 5-speed Clutch: Magura Hydraulic Chassis, suspension, brakes and wheels Frame type: Aluminum Twin-Spar Front suspension: 46mm Ohlins 12” Travel Front suspension travel: 305 mm (12.0 inches) Rear suspension: Ohlins POS 12.6” Travel Rear suspension travel: 320 mm (12.6 inches) Front brakes: Single disc. Dual piston, 240mm Rotor Front brakes diameter: 240 mm (9.4 inches) Rear brakes: Single disc. Dual piston, 220mm Rotor Rear brakes diameter: 220 mm (8.7 inches) Physical measures and capacities Dry weight: 109.8 kg (242.0 pounds) Power/weight ratio: 0.4373 HP/kg Seat height: 965 mm (38.0 inches) If adjustable, lowest setting. Ground clearance: 361 mm (14.2 inches) Wheelbase: 1,486 mm (58.5 inches) Other specifications Starter: Electric

Incoming search terms: