HARLEY DAVIDSON SISSY BAR LUGGAGE INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 19-02-2011

download
INSTALLATION Improper loading of cargo or installation of accessories can affect motorcycle stability and handling, which could result in death or serious injury. (00095a) Harley-Davidson cannot test and make specific recommendations regarding every accessory or combination of accessories sold, the rider must assume responsibility for safe operation of the motorcycle when installing accessories or carrying additional weight. Use the following guidelines when equipping a motorcycle or carrying passengers and cargo. •The Gross Vehicle Weight Rating (GVWR) is shown on the information plate located on the frame steering head. GVWR is the sum of the weight of the motorcycle and accessories and the maximum weight of the rider and cargo that may be carried safely. Do not pull a trailer with this motorcycle. Do not exceed the GVWR as indicated on the frame label. •Keep cargo weight concentrated close to the motorcycle and as low as possible to minimize the change in the motorcycle’s center of gravity. Distribute weight evenly on both sides of the vehicle and do not load bulky items too far behind the rider or add weight to the handlebars or front forks. •Do not exceed the maximum load (indicated on the label inside) in the bag. Do not exceed the capacity of the luggage rack. •Be sure cargo is secure and will not shift while riding. Periodically recheck the load. •Ensure that the bag strap buckles are secure •Large surfaces, such as fairings, windshields, backrests and luggage racks, can affect handling. These items should be designed and approved by Harley-Davidson specifically for the motorcycle model and be properly installed. 1. Disconnect the quick-disconnect buckle on the bottom mounting strap, and undo the D-ring fasteners on the back straps. Add enough slack to the straps to wrap around the luggage rack and backrest pad. 2. See Figure 1. Center the bag on the luggage rack with the closure buckles facing the back of the motorcycle. Bring the mounting strap on the bottom of the bag around the underside of the luggage rack

HARLEY-DAVIDSON BACKPACK INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 11-02-2011

download
INSTALLATION Improper loading of cargo or installation of accessories can affect motorcycle stability and handling, which could result in death or serious injury. (00095a) Harley-Davidson cannot test and make specific recommendations regarding every accessory or combination of accessories sold, the rider must assume responsibility for safe operation of the motorcycle when installing accessories or carrying additional weight. Use the following guidelines when equipping a motorcycle or carrying passengers and cargo. •The gross Vehicle Weight Rating (GVWR) is shown on the information plate located on the frame steering head. GVWR is the sum of the weight of the motorcycle and accessories and the maximum weight of the rider and cargo that may be carried safely. Do not pull a trailer with this motorcycle. Do not exceed the GVWR as indicated on the frame label. •Keep cargo weight concentrated close to the motorcycle and as low as possible to minimize the change in the motorcycle’s center of gravity. Distribute weight evenly on both sides of the vehicle and do not load bulky items too far behind the rider or add weight to the handlebars or front forks. Do not exceed 25 pounds (11 kilograms) maximum load in the backpack. •If attaching to a luggage rack, do not exceed the capacity of the rack. •Be sure cargo is secure and will not shift while riding. Periodically recheck load. •Ensure that the bag strap buckles are secure. •Secure backpack straps inside top pocket, keep away from rear wheel. •See Accessories and Cargo section of Owner’s Manual for more information. •Large surfaces, such as fairings, windshields, backrests and luggage racks, can affect handling. These items should be designed and approved by Harley-Davidson specifically for the motorcycle model and be properly installed.

Turbo+2 , Roadstar , Quantum Sport , Quantum"GL" , Entourage Owners Manual

0

Filed Under (Uncategorized) by admin on 03-12-2010

download
tracking Any parting within the tread, sidewall, or inner liner of the tire extending to cord material. CT A pneumatic tire with an inverted flange tire and rim system in which the rim is designed with rim flanges pointed radially inward and the tire is designed to fit on the underside of the rim in a manner that encloses the rim flanges inside the air cavity of the tire. Curb weight The weight of a motor vehicle with standard equipment including the maximum capacity of fuel, oil, and coolant, and, if so equipped, air conditioning and additional weight optional engine. Extra load tire A tire designed to operate at higher loads and at higher inflation pressures than the corresponding standard tire. Groove The space between two adjacent tread ribs. Gross AxleWeight Rating The maximum weight that any axle can support, as published on the Certification /VIN label on the front left side of the trailer. Actual weight determined by weighing each axle on a public scale, with the trailer attached to the towing vehicle. Gross Vehicle Weight Rating The maximum weight of the fully loaded trailer, as published on the Certification /VIN label. Actual weight determined by weighing trailer on a public scale, without being attached to the towing vehicle. Hitch Weight The downward force exerted on the hitch ball by the trailer coupler. Innerliner The layer(s) forming the inside surface of a tubeless tire that contains the inflating medium within the tire. Innerliner separation The parting of the innerliner from cord material in the carcass. Intended outboard sidewall The sidewall that contains a white-wall, bears white lettering or bears manufacturer, brand, and/or model name molding that is higher or deeper than the same molding on the other sidewall of the tire or the outward facing sidewall of an asymmetrical tire that has a particular side that must always face outward when mounted on a vehicle. Light truck (LT) tire A tire designated by its manufacturer as primarily intended for use on lightweight trucks or multipurpose passenger vehicles. Load rating The maximum load that a tire is rated to carry fora given inflation pressure. Maximum load rating The load rating fora tire at the maximum permissible inflation pressure for that tire. Maximum permissible inflation pressure he maximum cold inflation pressure to which a tire maybe inflated.
-9- Maximum loaded vehicle weight The sum of curb weight, accessory weight, vehicle capacity weight, and production options weight. Measuring rim The rim on which a tire is fitted for physical dimension requirements. Pin Weight The downward force applied to the 5thwheelor gooseneck ball, by the trailer kingpin or gooseneck coupler.

Incoming search terms:

ESCAPADE TRAILER Wheel Bearing Removal AND OWNER'S MANUAL

0

Filed Under (Tips and Review) by admin on 20-11-2010

download
1. Remove lug nuts and wheel assembly. Remove the cotter pin, adjusting nut (castle nut) and washer from the wheel spindle. 2. Pull the wheel hub towards you to loosen the outer bearing cone. Don’t Let the cone fall to the ground. As the hub is removed, the inner bearing and grease seal will come with it. Observe which direction the inner seal is facing. Pry out the inner seal and discard. 3. Remove all old lubricant from the hub assembly and wheel spindle with kerosene or mineral spirits. CAUTION: do not use gasoline to clean and remove the old lubricant). Inspect the spindle for scoring, bending, thread or other damage. A light grease coating on the spindle will make bearing installation easier and prevent rust from forming. 4. Inspect cups in the hub for pitting, metal flaking, scoring, rust or other obvious damage. Remove any damaged cups with a mild steel bar. Replace cups and cones in matched sets only; not one at a time. 5. Use cup driver or mild steel bar to press or drive the new cup into the hub Wheel / Rim: 12 X 4 JA (4 bolt, 4″ bolt diameter, 2½” rear space) Tire: 4.80 X 12 (B) (4 ply rated; cold pressure rated to 465 lbs. of load at 25 PSI). NOTE: These are standard utility trailer size tires and wheels. Using oversize tires or increasing tire pressures to a level higher than recommended will not increase the Gross Vehicle Weight Rating (GVWR). HUBS For maximum performance from your Sport Wheels and to avoid damage to your trailer, observe the following precautions: •When buying a replacement hub, check that the hub flange is no smaller than a diameter of ?”. •The replacement hub must accept the 1″ bearing (Part Number L44643) and matching cup. •Torque all lug nuts holding the wheel to 75 ft. lbs. TRAILING ARM / SWING ARM No maintenance is required for the trailing arm bearings for the life of the trailer. However, if the trailing arm is removed for any reason the following steps must be followed. 1. Once the ¾” X 16 hex nut has been removed, discard it, and replace with a new lock nut of the same design. 2. When replacing the trailing arm, be sure the bearing spacer is located between the bearings. 3. Torque the hex nut to 14 ft. lbs while moving swing-arm up and down.. DO NOT BACK OFF FOR ADJUSTMENT . Insufficient torque to the

Incoming search terms:

2009 Chief Vintage specification

0

Filed Under (Cobra) by admin on 17-11-2010

download
STYLING • Chromed tear drop Halogen Headlamp • Auxilliary driving lamps • Die cast console – color matched • Black and polished engine with chrome covers • Chromed spoke wheels • Available billet wheels • Two into one stainless steel exhaust system with three way catalytic c onverter and chromed shields • Available short skirt fenders and dual tone paint • Metal tank badge • Chrome fender tips (not pictured) • Chrome brake calipers (not pictured) • Chrome engine guards (not pictured) POWER TRAIN • Air cooled, pushrod Power Plus 105ci engine • Closed loop, sequential, port injection with heated oxygen sensors • Six speed transmission CHASSIS • Seat: Solo seat with passenger pillion, available in black, tan and red leather with fringe • Chrome grab rail • 5.5 gallon fuel tank • oating rotors and 4 piston calipers in oating rotor and two piston caliper in the rear. • Two accessory 12 V outlets • Tinted windshield • Saddle bags available in black, tan, or red leather with fringe ELECTRICAL • Tank mounted analog speedometer and multi function digital display • Charging system 42 Amps • Lamps: Tear drop head lamp, glass front fender light, auxilliary spot lights • There are no electrical relays in the system DIMENSIONS Note: All specification subject to change Length 100.5″ Width 40.5″ Height 50.5″ Seat Height Laden 26.69″ Seat Height Unladen 27.89″ Wheelbase 68.4″ Dry Weight (will vary for each model) 738 lbs Running Order Weight 773 lbs Rake Steering Head/Trail 34°/5.92″ GVW – Gross Vehicle Weight 1260 lbs ENGINE Engine Type Power Plus 105, Air-Cooled Displacement 105 Cubic Inches Bore x Stroke 3.966 x 4.25 Compression Ratio 9 to 1 Engine Torque 100 ft*lbs (TBD) Fuel System Closed Loop Sequential Port Fuel Injection DRIVETRAIN Primary Drive Chain Gearbox Six Speed Gear Ratio (overall) 1st 10.441:1 2nd 7.090:1 3rd 5.172:1 4th 3.984:1 5th 3.193:1 6th 2.771:1 Final Drive Belt CHASSIS Frame High tensile steel, monoshock Suspension/Front Diameter 41 mm/Travel 108 mm Suspension/Rear Single shock/travel 73 mm Brakes/Front Dual Caliper with Floating Rotors 11.5″ Diameter Brakes/Rear Single Caliper Floating Rotor 11.5″ Diameter Tires/Front 130/90-16 White Wall Tires/Rear 150/90-16 White Wall Wheels Wire spoked Exhaust System Two Into One Stainless Steel With Chromed Shields ELECTRICAL Electrical Instruments Tank mounted analog speedometer and muti function digital display Charging System 42 Amps Lamps Tear drop head lamp, glass front fender light, auxillary spot lights. WARRANTY 2 Years PRICING $35,499 delivery, set up and local taxes not included STANDARD COLORS Thunder Black AVAILABLE COLORS $199 Indian Red $899 Thunder Black & Winter White $899 Midnight Blue Metallic & Winter White $899 Thunder Black & Indian Red $899 Willow Green & Ivory Cream Indian Red & Ivory Cream Navajo Turquose & Winter White

2008 harley- davidson sportster specifications

0

Filed Under (Harley Davidson) by admin on 01-11-2010

download
diMensions Length 89.10 in. (2263.14 mm) Overall Width 35.20 in. (894.08 mm) Overall Height 46.80 in. (1188.72 mm) Seat Height: *•*Laden2 26.30 in. (668.02 mm) *•*Unladen* 28 in. (711.20 mm) Ground Clearance 4.40 in. (111.76 mm) Rake (steering head) 29.6° Fork Angle 29.6° Trail 4.70 in. (119.38 mm) Wheelbase 59.70 in. (1516.38 mm) Tires (Dunlop® Harley-Davidson® Series, blackwall) : *•*Front*-*D401F* 100/90-19 57h *•*Rear*-*D401* 150/80B16 71h Fuel Capacity (warning light at approximately 1 gal.) 4.5 gal. (17.03 L) Oil Capacity (w/filter) 3.60 qts. (3.41 L) Transmission Capacity 1 qts. (0.95 L) Weight: *•*As*Shipped** 557 lbs. (252.65 kg) *•*In*Running*Order* 581 lbs. (263.54 kg) *•*Gross*Vehicle*Weight*Rating* 1000 lbs. (453.59 kg) Gross Axle Weight Rating: *•*Front** 335 lbs. (151.95 kg) *•*Rear* 665 lbs. (301.64 kg) enGine Engine3 Air-cooled, Evolution® Valves* Pushrod-operated,*overhead*valves*with*hydraulic, ** self-adjusting*lifters;*two*valves*per*cylinder Bore x Stroke 3.50 in. (88.90 mm) x 3.81 in. (96.77 mm) Displacement3 73.20 cu. in. (1200 cu. cm) Compression Ratio 9.7:1 Fuel System4* Electronic*Sequential*Port*Fuel*Injection* (ESPFI) Air*Cleaner* Paper*cartridge*type Lubrication*System* Dry-sump drivetrain Primary*Drive** Chain,*57/38*ratio Final*Drive* Belt,*68/29*ratio Clutch** 9-plate,*wet Transmission 5-speed Gear Ratios (overall) : U.s.** HDI* JPN 1st 9.315 9.004 9.004 2nd 6.653 6.432 6.432 3rd 4.948 4.783 4.783 4th 4.102 3.965 3.965 5th 3.517 3.400 3.400 chassis Frame Mild steel, tubular frame; circular sections; cast junctions wing*Arm*Mild*steel,*rectangular*tube*sections,*stamped*junctions;*MIG*welded* Front Forks 39 mm Rear Shocks Coil-over; preload dual-adjustable Wheels5 (Chrome, Laced Steel option) : Black, 13-Spoke Cast Aluminum 105th Anniversary Wheels5 (Chrome, Laced Steel option) Gloss*Black*Painted*Cast*Aluminum *•*Front* 19 in. x 2.15 in. (482.60 mm x 54.61 mm) *•*Rear** 16 in. x 3 in. (406.40 mm x 76.20 mm) Brakes: *•*Caliper*Type* Dual-piston*front,*single-piston*rear* *•*Rotor*Type* (diameter x width) :** Patented,*uniform*expansion*rotors** *•*Front* 11.50 in. x .20 in. (292.10 mm x 5.08 mm) *•*Rear** 11.50 in. x .23 in. (292.10 mm x 5.84 mm) Suspension Travel: *•*Front*Wheel* 4.12 in. (104.65 mm) *•*Rear*Wheel* 2.12 in. (53.85 mm) perforMance Engine Torque6 (per SAE J1349) : *•*North*America* 79 ft. lbs. @ 4000 rpm* (107.12*NM*@*4000*rpm) *•*World** 75 ft. lbs. @ 3500 rpm* (101.70*NM*@*3500*rpm) *•*Japan* 66 ft. lbs. @ 3500 rpm* (89.50*NM*@*3500*rpm) Lean Angle (per SAE J1168) : Right: 31° Left: 30° Fuel Economy7 (EPA urban/highway test) : 42/57 mpg (5.60/4.13*L*/100*km) electric Battery** Sealed,*maintenance-free,*12V,*12-amp/hour,*200*cca (per Battery Council International Rating) Charging Single-phase, 30-amp system (357W*@*13.5V,*2000*rpm,*405W*max*power*@*13.5V) Starting* 1.2*kW*electric*with*solenoid*shift*starter*motor*engagement Lights (as per country regulation) : *•*Headlamp* (quartz halogen) * 55-watt*low*beam,*60-watt*high*beam* **•*Tail/Stop*Lights* 8W/28W* (5W/21W)* *•*Turn*Signal*Lights** 28W (21W) self-canceling *•*Indicator*Lamps* High*beam,*neutral,*low*oil*pressure,*turn*signals,** **