HARLEY DAVIDSON CHROME 1.25 INCH (31.75 MM) DIAMETER HANDLEBAR KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 10-03-2011

download
CHROME 1.25 INCH (31.75 MM) DIAMETER HANDLEBAR KIT GENERAL Kit Number 56032-08 Models For model fitment information, see the P&A retail catalog or the Parts and Accessories section of www.harley-davidson.com (English only). This kit does not fit models equipped with a hydraulic clutch, handlebar mounted gauges or the Road Tech® Radio. Additional Parts or Accessories Required Separate purchase of additional parts or accessories is required for proper installation of this Handlebar Kit on this model motorcycle. Please see the P&A retail catalog or the Parts and Accessories section of for a list of required parts or accessories for this model. For Australia, Brazil, England, Europe and Japan, two special screws (Part Number 2935A) will also be required. Tools and Supplies Required Loctite® 271 Threadlocker and Sealant – Red (H-D Part Number 99671-97) is required for the proper installation of this kit. Fresh, uncontaminated DOT 4 brake fluid from a sealed container will also be needed. Replace brake line gaskets. Re-using original gaskets can cause brake failure and loss of vehicle control, which could result in death or serious injury. (00318a) For models that retain the original brake line, the two brake- line gaskets found at each banjo fitting must be replaced . Refer to the appropriate parts catalog or see a Harley-Davidson dealer for the correct part numbers. Motorcycles equipped with a glued left-side hand grip will also require a new grip, sold separately. Refer to the parts catalog for replacement stock hand grips. Ask a Harley-Davidson dealer about the selection of Genuine Motor Accessory hand grips that are available. The rider’s safety depends upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333a) NOTE This instruction sheet references service manual information. A service manual for this year and model motorcycle is required for this installation and is available from a Harley-Davidson dealer. Kit Contents See Figure 6 and Table 1. INSTALLATION Preparation To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative (-) cable first) before proceeding. (00307a) Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 1. Refer to the service manual and follow the instructions given to remove the seat and disconnect the battery cables, negative cable first. Retain all seat mounting hardware. Direct contact of D.O.T. 4 brake fluid with eyes can cause irritation. Avoid eye contact. In case of eye contact flush with large amounts of water and get medical attention. Swallowing large amounts of D.O.T. 4 brake fluid can cause digestive discomfort. If swallowed, obtain medical attention. Use in well ventilated area. KEEP OUT OF REACH OF CHILDREN. (00240a) D.O.T. 4 brake fluid will damage painted and body panel surfaces it comes in contact with. Always use caution and protect surfaces from spills whenever brake work is performed. Failure to comply can result in cosmetic damage. (00239b) NOTE Immediately wipe up any brake fluid spillage with a clean, dry, soft cloth. Follow up by thoroughly wiping affected area with a clean, damp, soft cloth (small spills) or washing with a large quantity of soapy water (large spills)

Incoming search terms:

HARLEY DAVIDSON AILERON HAND GRIPS REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 01-03-2011

download
LEFT GRIP REMOVAL AND INSTALLATION 1. See Figure 1. Using a T27 TORX® drive head, remove the two screws with flat washers securing the handlebar clamp (3) to the clutch lever bracket. Remove the clamp, and position the clutch hand lever assembly away from the handlebar. 2. Using a T25 TORX drive head, loosen but do not remove the upper and lower switch housing screws (1). 3. Remove the end cap from the existing left hand grip if so equipped. With “glueless” grip: Remove the grip from the han- dlebar. With glued grip: Remove the grip by carefully cutting it away from the handlebar using a sharp blade or knife. NOTE Make sure that the handlebar surface and the inside of the new grip are smooth, dry and thoroughly cleaned of all dirt or adhesive residue. Do not lubricate left handlebar grip before installation. Lubricating grip can cause it to come off while riding, which could result in loss of control and death or serious injury. (00315a) 4. Position the new left grip (4) so the larger diameter portion of the flange (5) is at the bottom. Push the grip fully onto the handlebar. 5. Fit the grooves (2) on the outboard side of the upper and lower switch housing over the flanges on the end of the grip, then loosely fasten the two screws. 6. Position the clutch hand lever assembly inboard of the switch housing assembly, engaging the tab on the lower switch housing in the groove at the bottom of the clutch lever bracket. 7. Align the holes in the handlebar clamp with those in the clutch lever bracket, and loosely fasten the two screws with flat washers. Adjust the switch housing and clutch hand control position for rider comfort. 8. Using a T27 TORX drive head, tighten first the upper, then the lower handlebar clamp screws to 60-80 in-lbs (6.8- 9.0 Nm). 9. Using a T25 TORX drive head, tighten first the lower, then the upper switch housing screws to 35-45 in-lbs (4.0-5.1 Nm)

Motorcycle Hand Warmer Installation Instructions

0

Filed Under (Tips and Review) by admin on 29-01-2011

download
1. Disconnect the Positive (+) terminal from the battery. 2. Remove the existing grip from the Clutch side. Removing the grip may require blowing compressed air in the end between the grip and the bar, injecting brake cleaner fluid, or cutting it off. 3. Clean the handlebar where the grip was removed with alcohol or a solvent to remove all residue and dry with a clean cloth. 4. Determine where the Clutch side heater will be mounted. Take the heater marked “Clutch” and place it on the handlebar approximately ½” from the end and decide the position of the wires. It is recommended to mount the heater so the wires are at 9:00 o’clock or they can be positioned on the bottom for appearance. Peel off the release paper and adhere the heater to the handlebar with the wires toward the headlight. 5. Apply a high temperature adhesive (such as JB Weld) to the inside of the Clutch side grip. Install the grips over the heaters and let the adhesive cure as instructed by the adhesive manufacturer. 6. The Throttle side heater is installed on the throttle sleeve under the rubber cover. Remove the rubber cover that is installed over the throttle sleeve so the Throttle side heater can be applied. Some of the throttle sleeves have ribs which need to be cut or ground off so the heater can make full contact with the sleeve surface or it will over heat in the void areas. 7. Determine where the throttle side heater will be mounted. Take the heater marked “Throttle” and place it on the throttle sleeve approximately ½” from the end and decide the position of the wires. It is recommended to mount the heater so the wires are at 3:00 o’clock with a loop to allow for the twisting motion of the throttle. Peel off the release paper and adhere the heater to the throttle sleeve with the wires toward the headlight. 8. Apply a thin coat of adhesive (such as J.B. Weld) to the surface of heater only and reroll the rubber hand grip over the entire throttle sleeve. Wipe off any excessive adhesive that may have rolled out

BMW K1200RS Electronic Cruise Control installation instructions

0

Filed Under (BMW) by admin on 26-10-2010

download
We recommend that you take power from a non-critical circuit such as the heated grip circuit. Any power supply wire that is green with a black trace (stripe) is a fused, switched 12V supply. That is, there is a fuse in the line, and the ignition switch turns the power to the wire on and off, and it is NOT powered when the ignition switch is in the ‘park’ position (side lights turned on). Because the ignition switch also powers the ABS system, if the heated grip circuit is live, in theory the ABS system, and therefore the brake light system, will also be live. • On the bikes that we have fitted the cruise control to, there is a three way plug behind the headlight, that goes to the heated hand grip switch (on the right side handlebar). This plug has one green/black wire, a black wire and an orange wire. This photo is taken looking down below the bike’s instruments on the right side. The plug is circled. • This photo is taken from the front of the bike looking back through the head light cavity, under the bikes instruments. The plug is circled. • This is a convenient and accessible location to pick up power for the cruise control. The cruise control orange power wire should be connected to the green/black power wire for the heated grips.

Incoming search terms: