Harley-Davidson CHAIN DRIVE INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 15-04-2012

download
1) Assemble & install the chain tensioner assembly over the primary chain as shown in figure 1. 2) Install the compensator sprocket with extender & spacer (numbers 5, 6, & 7, FIG 2)(#7 is not included in this kit), primary chain, chain tensioner, and clutch basket simultaneously onto the motor drive shaft & transmission main shaft. Rotate the chain drive slightly as needed to allow the splines to line-up. 3) Install the chain tensioner nut loosely on the chain tensioner bolt. 4) Install the sliding cam onto the compensator sprocket, & slide the compensating sprocket cover-assembly (#3) over the cam. 5) Apply 2 drops of Rivera “Red” thread-lock on the threads of the motor drive shaft, & install the motor nut loosely with the fingers at this time. The hex spacer (#7) and spacer (#2) as seen in fig.2 are not provided in Rivera Engineering’s chain drive kit. These components are required with some applications, and can be purchased from your local Harley-Davidson dealer. FIG 2 6) Apply 2 drops of Rivera “red” thread-lock on the threads of the transmission main-shaft and loosely install the clutch hub nut (left hand threads). 7) Place the HD “Primary Drive Locking Tool” HD-41214 on the primary chain as shown in figure XXX and tighten the motor sprocket nut to 150-165 foot-pounds. 8)Turn the locking tool 180 degrees and move it to the clutch sprocket. Tighten the clutch hub nut to 70-80 foot pounds (left- hand thread). Adjust chain tension so that the top strand has 5/8″- to-7/8″ of up and down play (cold drive train). Tighten the center bolt nut to 21-29 foot pounds of torque.

Incoming search terms:

2006 Harley Davidson VROD / Screamin' Eagle VROD Installation Manual

0

Filed Under (Harley Davidson) by admin on 01-03-2012

download
Check top clamp holding on rear heat shield be sure this is mounted forward not in middle of pipe. 2. Slide rear head pipe into collector and leave loose. 3. Mount head pipes into exhaust ports using stock Harley gaskets hand thread nuts onto head studs, leaving play in pipes. 4. Slip muffler onto collector and leave loose. 5. Slide D&D bracket included with kit onto chassis and muffler together. 6. Hand thread nuts onto chassis studs 7. Align muffler flush with bracket, hand thread bolts onto muffler.
8. Push system together tightly, Tighten rear head pipe collector clamp. 9. Holding muffler into place (finger width between shock bolt) tighten down muffler clamp all the way. 10. Snug (do not torque) chassis bracket bolts, snug muffler bolts until all is correctly aligned, then tighten down bolts. 11. Tighten head bolts down using factory torque specs, as you tighten the pipe check muffler clearance. If to close to swing arm push in on head pipe. If to far away push in on head pipe. 12. Once all is tight start bike and check for leaks This system is designed to be used with a high flow air filter and D&D VRDSEDD2.MT4 Race Tuner map.

CR500R/ 500 AF Hi Power Digital Ignition & Light Coil Installation Instructions

0

Filed Under (Honda) by admin on 19-11-2011

download
Place the motorcycle on a secure stand. 2.Remove the fuel tank and radiator shrouds. 3.Remove the front number plate if CDI unit is located behind number plate. 4.Remove CDI Ground from coil. 5. Remove Old CDI.b6. Remove ignition cover. 7. Use an electric, pneumatic impact to remove flywheel nut. 8. Use flywheel puller to remove flywheel. Thread the flywheel puller into the flywheel by turning the puller counter clockwise (left hand thread). Turn flywheel puller center nut clockwise with an impact set to low to remove flywheel. 9. Remove 2 bolts that secure the stator. 10. Remove stator. 11. Install new stator by aligning the index mark on the lower stator plate with the index mark on
the left crankcase. 12.Install and tighten stator bolts to 9 ft-lbs. (1.2 bkg-m). 13. Install new flywheel and tighten flywheel nut to 40ft-lb (5.5 kg-m). 14. The pulser gap is preset to .012”. If you have trouble starting you bike after installation confirm the gap between the pulser and the ignition trigger on the flywheel is .012”. Use a good/no good
technique when checking and adjusting the gap. The largest feeler that will fit without forcing the feeler into the gap is the current gap

ATK 50MX INSTALLATION AND ADJUSTMENT TIPS

0

Filed Under (Atk) by admin on 01-11-2010

download
PRELOAD ADJUSTMENT— On some Works shocks a threaded preload is standard. This allows the adjustment of the ride height of the motorcycle. The preload is changed by turning a threaded nut down towards the spring (higher ride height) or up away from the spring (lower ride height). The nut is a right-hand thread. CHECKING RIDE HEIGHT— 1. With the bike unloaded on the side stand and the shock fully extended, have an assistant measure from a point at the axle (center point) to a point on the frame, fender or bodywork directly above it. Record this measurement. 2. With the bike off the stand and the rider in the seat, bounce on the suspension and let the bike settle. Have the assistant measure from the same two points. Subtract the second measurement from the first. HM CRX50 / BAJA & ATK 50MX INSTALLATION AND ADJUSTMENT TIPS Continued on next page. #HM50 – 5/27/99 #HM50 – 5/27/99 To Front Valve Mounting channel Spacer Flange Shock eye Top View of Shock Mount Fig. 1 Top view of upper shock mount. The flange on the shock bushing must face toward the spacer. The valve should point toward the front of the bike Fig. 1 Top view of upper shock mount. The flange on the shock bushing must face toward the spacer. The valve should point toward the front of the bike 3. The amount of settle, or “sag” is a function of the wheel travel. It should only be between 1/4 and 1/3 of the total travel. 4. If the difference is less than the minimum, reduce the spring preload. Measure the distance again starting with Step 2. Adjust again if necessary. 5. If the difference is more than the maximum, increase the spring preload. Measure the distance again starting with Step 2. Adjust again if necessary. Note: If the ride height is too low, the shock will bottom unnecessarily, resulting in a harsh ride. If the ride height is too high, the shock will “top out” too easily when rebounding from a bump or under hard deceleration. NITROGEN PRESSURES IN EMULSION SHOCKS CAUTION: The pressure in these shocks cannot successfully be checked. Concerns with the gauge volume and the gas volume in the shock body create a situation where you cannot accurately determine what pressure was in the shock. In addition when the pressure is lowered (i.e. checking the pressure) the gas and some of the shock oil escapes into the gauge. It is possible to lose a large percentage of the shock oil by depressing the core of a charged shock to the atmosphere. Please note that in order to check the pressure, some of the gas must escape and fill the gauge assembly. The volume of the gas pocket is about half the size of your thumb, so a very small volume change results in a large pressure drop. Because the gauges’ volumes vary, it is not possible to deduce the actual pressure in the shock prior to attaching the gauge. Therefore it is imperative that any attempt to check pressure be accompanied by the capability of refilling the shock. In other words: If you don’t have a nitrogen source handy, don’t check the pressure! PRESSURIZING EMULSION SHOCKS The pressure setting for Works gas shocks is 250 p.s.i. of dry nitrogen. To pressurize a shock with some residual pressure in it, bring the gauge manifold up to 250 p.s.i. and depress the core with the T-handle. This will either equalize the pressure or refill the shock without transferring oil from the shock into the gauge assembly. The best gauges for this purpose screw on to the valve and incorporate a T-handled core depressor to isolate the shock from the gauge. This allows a leak-free separation once the desired pressure is reached. For simplified operation, an extra valve is provided for the filling apparatus, allowing pressure adjustment with the gauge in place. Works offers a suitable gauge and filling manifold. Most motorcycle shops that deal with dirt bikes can pressurize the shock

Incoming search terms:

1937-1984 Big Twins BRUTE II EXTREME BELT DRIVES INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 27-10-2010

download
Remove the outer primary cover. Remove the front pulley, chain, compensator & chain adjuster Remove oil lines to primary and plug or clamp to prevent leakage. Cut the chain oiler hose 3 inches from the oil pump and permanently plug. All belts must be run dry without lubrication of any kind. Therefore, remove all oil from inside the primary covers. The spacer behind the front pulley should be removed prior to installing the belt drive. This spacer may or may not be required to correctly align the pulleys. If a spacer is needed for alignment, various sizes are available from your local Primo Belt Drives dealer (part number PX-1 =package of 6 various sizes). Install the front pulley supplied in the kit. Loop the belt around both pulleys to insure that you have the proper belt for your pulleys, then gently push the unit into place. Use the supplied washer & nut on the motor shaft. Torque the motor nut to 80-100 foot pounds. If installing a PC-1000-Aremove the clutch hub & clutch basket. On tapered shaft models check the fit on the shaft & the fit of the keyway in the hub. Install the key in the mainshaft, making sure it is firmly seated (use of super glue or threadlock in the keyway is helpful to keep the key from sliding out of the keyway during clutch installation). Tighten the clutch hub nut(left-hand thread) to 60-90 foot pounds. 1 After installing and adjusting clutch, track the belt by turning the pulleys. If needed use a straight edge between the front and rear pulleys to check alignment. Improper alignment of the pulleys will result in reduced belt life. Spacing the motor pulley outward will cause the belt to track towards the outer primary cover. If spaced too far out the belt will rub on the inside of the clutch shell. Before installing the primary cover be sure that everything inside clears both the outer and inner covers. In some cases a small amount of metal may need to be removed from one or more of the bosses on the inner or outer primary cover.

Incoming search terms: