Harley davidson American Classic Straights on a 1988-2001 VLX 600 Shadow Installation Instructions

0

Filed Under (Harley Davidson) by admin on 01-03-2012

download
Remove right side Foot peg assembly or Floorboard. (Whichever is applicable to your model.) 2. Remove bolts that are holding pipes at rear mounting bracket. 3. Loosen clamps at mufflers. 4. Remove mufflers. 5. Remove the two nuts that secure the rear exhaust header pipe to the rear cylinder head. 6. Remove rear exhaust pipe assembly. 7. Remove the two nuts that secure the front exhaust header pipe to the front cylinder head. 8. Remove front exhaust pipe assembly. 9. Remove exhaust-mounting bracket from frame. Hard-Krome Exhaust System Installation NOTE: Take care when fitting this Hard-Krome aftermarket exhaust system on your motorcycle. It has been designed to replace a STOCK exhaust system on a motorcycle with its engine, frame and other components in their STOCK design, configuration and location. WARNING : Re-check and re-tighten ALL fasteners and supports after 50 miles, then re-check and tighten as necessary on a periodic basis to ensure proper operation and performance. NOTE: All fasteners should be loose during initial installation to ensure proper fit and location of the new exhaust system.
1. Install new exhaust gaskets. 2. Install mounting bracket using Bolts with flat & lock washers. (See Illustration) 3. Install Front exhaust header pipe, taking care to not scratch chrome surfaces on pipe, engine or motorcycle — use masking tape as needed. 4. Install the two nuts to secure the flange that holds the exhaust header pipe to the front cylinder head — DO NOT TIGHTEN NUTS! 5. Install nut strip into slotted bracket of front pipe and start the 3/8-16×3/4″ Bolt with flat & lock washer through backside of mounting bracket. — DO NOT TIGHTEN BOLTS! 6. Carefully install rear pipe. 7. Install the two nuts to secure the flange that holds the exhaust header pipe to the rear cylinder head — DO NOT TIGHTEN NUTS! 8. Install nut strip into slotted bracket of rear pipe and start the 3/8-16×3/4″ Bolt with flat & lock washer through backside of mounting bracket. — DO NOT TIGHTEN BOLTS! 9. Tighten the two bolts that secure the rear exhaust header pipe flange. 10. Tighten the two bolts that secure the front exhaust header pipe flange. 11. Tighten front pipe bolts at mounting bracket. 12. Tighten rear pipe bolts at mounting bracket. 13. Reinstall foot peg assembly or floorboard. 14. If applicable to your model install foot peg relocating brackets and foot pegs as shown in illustration. 15. Before starting bike wipe off any fingerprints and grease off pipes. Start bike and check for any exhaust leaks.

Incoming search terms:

Yamaha Stratoliner 2006 3" Big Straights REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 02-01-2012

download
1. Remove right side Foot peg assembly or Floorboard. (Whichever is applicable to your model.) 2. Remove bolts that are holding muffler at rear mounting bracket. 3. Remove Cables from exhaust valve. 4. Remove O2 Sensor from pipe. 5. Remove the two nuts that secure the rear exhaust header pipe to the rear cylinder head. 6. Remove the two nuts that secure the front exhaust header pipe to the front cylinder head. 7. Remove complete pipe assembly. Hard-Krome Exhaust System Installation NOTE: Take care when fitting this Hard-Krome aftermarket exhaust system on your motorcycle. It has been designed to replace a STOCK exhaust system on a motorcycle with its engine, frame and other components in their STOCK design, configuration and location. WARNING : Re-check and re-tighten ALL fasteners and supports after 50 miles, then re-check and tighten as necessary on a periodic basis to ensure proper operation and performance. NOTE: All fasteners should be loose during initial installation to ensure proper fit and location of the new exhaust system. 1. Install new exhaust gaskets. 2. Install mounting bracket using Bolts with flat & lock washers. (See Illustration) 3. Install O2 Sensor onto front pipe and install front pipe onto front cylinder, taking care to not scratch chrome surfaces on pipe, engine or motorcycle. 4. Install the two nuts to secure the flange that holds the exhaust header pipe to the front cylinder head — DO NOT TIGHTEN NUTS! 5. Install 3/8-16 Square nut into each slotted bracket of front pipe and start the 3/8-16×3/4″ Bolt with flat & lock washer through backside of mounting bracket. — DO NOT TIGHTEN BOLTS! 6. Carefully install rear pipe onto rear cylinder. 7. Install the two nuts to secure the flange that holds the exhaust header pipe to the rear cylinder head — (Remove chrome plastic valve cover to access top nut) — DO NOT TIGHTEN NUTS! 8. Install 3/8-16 Square nut into each slotted bracket of rear pipe and start the 3/8-16×3/4″ Bolt with flat & lock washer through backside of mounting bracket. — DO NOT TIGHTEN BOLTS! 9. Tighten the two bolts that secure the rear exhaust header pipe flange. 10. Tighten the two bolts that secure the front exhaust header pipe flange. 11. Tighten front pipe bolts at mounting bracket. 12. Tighten rear pipe bolts at mounting bracket. 13. Reinstall foot peg assembly or floorboard. 14. If applicable to your model install foot peg relocating brackets and foot pegs as shown in illustration.

Incoming search terms:

2002 Honda VTX 1800 R & S 3” BIG Straights Installation Instructions

0

Filed Under (Honda) by admin on 17-11-2011

download
Remove right side Foot peg assembly or Floorboard. (Whichever is applicable to your model.) 2. Remove O2 sensors from each muffler and cover with supplied cap plug. 3. Loosen clamps at mufflers. 4. Remove bolts that are holding mufflers at rear mounting bracket. 5. Remove mufflers. 6. Remove the two nuts that secure the rear exhaust header pipe to the rear cylinder head. 7. Remove rear pipe assembly. 8. Remove the two nuts that secure the front exhaust header pipe to the front cylinder head. 9. Remove front pipe assembly. Hard-Krome Exhaust System Installation
NOTE: Take care when fitting this Hard-Krome aftermarket exhaust system on your motorcycle. It has been designed to
replace a STOCK exhaust system on a motorcycle with its engine, frame and other components in their STOCK design,
configuration and location. WARNING: Re-check and re-tighten ALL fasteners and supports after 50 miles, then re-check and tighten as necessaryon a periodic basis to ensure proper operation and performance. NOTE: All fasteners should be loose during initial installation to ensure proper fit and location of the new exhaust system. 1. Install new exhaust gaskets. 2. Install mounting bracket using Bolts with flat & lock washers. (See Illustration) 3. Install Front exhaust header pipe, taking care to not scratch chrome surfaces on pipe, engine or motorcycle — use masking tape as needed

Incoming search terms: