HARLEY DAVIDSON FLSTN SADDLEBAG GUARD KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 06-03-2011

download
REMOVAL All Models 1. If equipped with saddlebags, removal may ease installation. Follow the instructions in the appropriate Service Manual or Instruction Sheet. 2. See Figure 1. Remove and discard the forwardmost fender support bolt (1). Repeat for the other side. 3. See Figure 2. On the left side, remove the footrest support mounting bolt (1) and footrest support bracket assembly (2). Discard the mounting bolt. 2005 – 2006 Models 1. Loosen the exhaust shields as necessary following the instructions in the appropriate Service Manual. Move as necessary for access. 2. Loosen the exhaust header nuts following the instructions in the appropriate Service Manual. 3. See Figure 3. Remove bolt (1) connecting the exhaust system (2) to the support bracket (3). 4. See Figure 4. Remove the two rear muffler bracket bolts (1). 5. See Figure 5. Move mufflers enough to access the rear bolt attaching the exhaust mounting bracket to the frame. Remove bolt (1) and discard. 2007 – Later Models NOTE On 2007 – later models, the frame tab (4) has a plug instead of a bolt (see Figure 6, item 1). 1. Remove plug and discard. 1 is05313 1. Fender support bolt (discard) Figure 1. Remove Docking Hardware 1 2 is05320 1. Footrest support mounting bolt 2. Footrest support bracket assembly Figure 2. Footrest Support Bracket Assembl NSTALLATION Right Side See Figure 5 or Figure 6. 1. See Figure 7. Install upper screw (7) in the fender support. Tighten screw finger-tight. 2. Install the lower screw (4 or 5) with the saddlebag guard, washer (9) and locknut (6) inside the frame. Tighten screw finger-tight. 3. Tighten the upper screw to 30 ft-lbs (41 Nm) . 4. Tighten the lower screw to 40 ft-lbs (54 Nm) . Tighten nut to 30 ft-lbs (41 Nm) . 5. 2005 – 2006 Models: a. Loosely install the exhaust header bolts. b. See Figure 4. Loosely install two rear muffler bracket bolts (1). c. See Figure 3. Loosely install bolt securing exhaust system (2) to support bracket (3). d. Tighten exhaust header bolts following the instructions in the appropriate Service Manual. e. Tighten support bracket bolt and rear muffler bracket bolts following the instructions in the appropriate Service Manual. f. Tighten exhaust shields following the instructions in the appropriate Service Manual. 6. Install saddlebag (if removed) following the instructions in the appropriate Service Manual or Instruction Sheet. 1 2 3 4 is05333 1. Lower saddlebag guard screw 2. Upper saddlebag guard screw 3. Saddlebag guard 4. Exhaust support bracket Figure 5. Install Saddlebag Guard – Right Side Shown (2005 Models) -J04645 2 of 4
2 1 3 4 is05332 1. Lower saddlebag guard screw 2. Upper saddlebag guard screw 3. Saddlebag guard 4. Frame tab Figure 6. Install Saddlebag Guard – Right Side Shown (2007-Later Models) Left Side 1. Loosely install upper screw (7) through the saddlebag guard and the fender support. NOTE Spacer (8) must be installed with the chamfer facing out. 2. See Figure 7. For 2005-2006 Models: Install lower screw (3) through the saddlebag guard, saddlebag guard spacer (8), footpeg support and the frame. Tighten to 30 ft-lbs (41 Nm) . For 2007 and later Models: Install lower screw (10) through the saddlebag guard, footpeg support and the frame. Tighten to 30 ft-lbs (41 Nm) . 3. Tighten upper screw to 30 ft-lbs (41 Nm)

Incoming search terms:

HARLEY DAVIDSON STREAMLINER PASSENGER FOOTBOARD KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 25-02-2011

download
REMOVAL 1. See Figure 1. Remove existing passenger footpegs or footboards, brackets and mounting hardware. 1 4 3 2 is04325 1. Screw and washer 2. Bracket 3. Footpeg mount 4. Footpeg pad and bottom Figure 1. Passenger Footpeg Components (FLHX) INSTALLATION NOTES • If necessary, remove any paint from counterbore holes of footboard brackets to ease the installation of the pivot pins. • On 2010 and Later Models: The installation height can be adjusted to one of three positions. To install footboards in a new position, remove plastic plugs from holes in rear swingarm bracket as necessary. • On 2009 and Earlier Models: The lowest of the four holes on the frame is not threaded and cannot be used to mount the footboards. 1. See Figure 2. Insert shoulder bolt (9) or (10) through slot in footboard bracket (1). a. 2010 and Later Models: Thread the 5/16 inch shoulder bolt (9) into the lowest hole in the rear swingarm bracket of the frame. b. 2009 and Earlier Models: Thread the 3/8 inch shoulder bolt (10) into the second lowest hole in the rear swingarm bracket of the frame. Tighten the bolts to 48-72 in-lbs (5-8 Nm.) . 2. At the desired height, install the upper screw (2) and lockwasher (3) through footboard bracket (1). Tighten screw to 36-42 ft-lb (49-56 Nm) . 3. Install spring (4) into retaining hole in footboard bracket. Set the ball (5) on top of spring. 4. Position the detent in the bottom of the footboard pan (8 or 12) over ball in footboard bracket. Be sure not to unseat the ball. Press down on footboard pan so the holes of the footboard pan and footboard bracket align. 5. Insert pivot pins (7) through two mounting holes on footboard bracket and into footboard pan. 6. Align footboard insert (6 or 11) in footboard pan. Press insert firmly until the footboard pan tabs are firmly seated in the footboard insert. 7. Fold footboard up and install set screw (13) to secure footboard pad. 8. Pivot footboard assembly up and down to verify proper operation. 9. Repeat all steps for opposite side

Harley-Davidson FLH Accent Panel Installation Manual

0

Filed Under (Harley Davidson) by admin on 16-02-2011

download
1 Install Accent Panels Note: See hardware list on Page 4 for usage and descriptions. 1.1 Elevate the rear of the vehicle and support with jack stands under the rear differential tubes. 1.2 Remove the rear wheels 1.3 Remove the passenger foot rests. 1.4 Remove front fairing (for wiring later in installation) . 1.5 Install cross brace and frame clamps to frame in the approximate position shown in Figure 1. 1.6 Note orientation of cross brace (Figure 2). Flat side of the brace against bottom of frame tubes. Outboard tabs up and to the rear of the vehicle. 1.7 Leave the bolts loose to allow the bracket’s position to be adjusted later in installation. 1.8 Install front brackets to vehicle between the frame and crash bars as shown, using the supplied hardware (the left side bracket is longer than the right. Figure 3 1.9 Leave the bolts loose to allow the bracket’s position to be adjusted later in installation. 1.10 Position the accent panel to vehicle. Figure 4 1.11 Install supplied hardware to front and cross brackets. Figure 5 &Figure 6 1.12 Leave the bolts loose to allow the accent panel’s position to be adjusted later in installation. 1.13 If not already preinstalled to your accent panel, install rubber bead edge molding between trike body (fender) and accent panel. Bead edge molding 1.14 Clamp the accent panel to the body (fender). Check position of accent panel and ensure proper positioning of bead edge molding. 1.15 Four holes will be drilled though body (fender) and accent panel in the approximate positions shown (both left and right accent panels). Figure 8 Note: Hole location dimension in Figure 8 are approximations. Your drill location may and can vary. Note: Hole position should be as high an possible on the accent panel, allowing space to install hardware 1.16 With accent panel and bead edge molding properly positioned and clamped to body (fender), Drill the two outboard holes in the approximate position shown from inside the fender well through mounting surface of accent panel. Note: Drill outboard hole first and install hardware to reduce risk of accidental movement. Figure 9 1.17 Drill remaining two inboard holes from the accent panel mounting surface through the body (fender). Figure 10 1.18 With both left and right accent panels installed, tighten all hardware at the left and right front mounting positions. 1.19 Trim off excess bead edge molding. 1.20 With left and right front mounting secure, check position and alignment of cross bar and accent panel mid mounts and tighten all hardware. 1.21 With fairing removed, crimp supplied xxx to the black, purple and blues wires of the vehicle’s turn signal wire loom. 1.22 Crimp one of the supplied male spade connectors to the end each wire from the accent panel. 1.23 Connect wiring as indicated in Table 1 below. Accent Panel Wire Color Vehicle Turn Signal Loom Wire Color Yellow Purple (Signal) Orange Blue (Running) Black Black (Ground) Table 1

HARLEY DAVIDSON CHROME ON/OFF SWITCH CAP KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 08-02-2011

download
INSTALLATION Models WITH maxi-fuse: To prevent accidental vehicle start-up, which could cause death or serious injury, remove maxi-fuse before proceeding. (00251a) 1. Refer to the Service Manual and follow the instructions given to remove the maxi-fuse. Models WITHOUT maxi-fuse: To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) 1. Refer to the Service Manual and follow the instructions given to remove the seat and disconnect the negative (black) battery cable from the negative (-) battery terminal. Retain all seat mounting hardware. 1 2 is0771a 1. Auxiliary accessory housing cover 2. Cover screw (2) Figure 1. Auxiliary Accessory Housing 2. ALL models: If the Auxiliary Accessory Housing Kit and the Rocker Switch(es) ARE NOT already installed on the motorcycle handlebar: a. Proceed to Step 3 of these instructions. Install a chrome switch cap onto each switch before installing the Auxiliary Accessory Housing Kit onto the vehicle. If the Auxiliary Accessory Housing IS already installed on the motorcycle handlebar: a. See Figure 1. Using a T-25 TORX® driver, remove the two screws (2) retaining the Auxiliary Accessory Housing cover (1), and remove the cover. b. See Figure 2. Remove the switch mounting bracket, along with any attached switch(es) and accessories, from the switch housing. Note: it is not necessary to remove the switch from the mounting bracket, or to disconnect the switch wiring to replace the switch caps

440 Series Shocks Installation Manual

0

Filed Under (Tips and Review) by admin on 14-12-2010

download
Follow instructions in an authorized shop manual or take the motorcycle toacompetent dealer. The motorcycle must be on thecenterstand (if equipped) or securely blocked to prevent it from tipping over when the shocks are removed. Failure to do so can cause serious damage and/or injury. The use of any lowering blocks is not recommended and will void the warranty. Make sure that proper bushings/sleeves are installed in the shocks. Improper bushings/sleeves can cause unsatisfactory and/or unsafe operation (seethe instructions packaged with the mounting hardware). 1. Place a quality jack or sufficient blocks under the motorcycle to securely lift the rear wheel slightly off the ground. 2. Using the correct shop manual, remove the old shocks and note location of the mounting hardware. If additional accessories are installed on your motorcycle, please refer to their mounting instruc- tionsforremoval to gain access to your shocks. 3. Before installing your new Progressive shocks you need to check the tire to fender clearance, (see Ain figure1) making sure that the tire does not come in contact with the fender. If the rear fender or tire has been changed to anything other than stock, a travel limiter maybe required. On some models with side bags or luggage, removal of the lower cover maybe required to eliminate any interference. Install shock assemblies onto the motorcycle (shaft end must be down!) and tighten bolts/nuts to proper torque. Check the clearances of the shock to frame (B) and shock to chain, chain guide, disc caliper and linkage (C) in figure 1. The lower cover can be removed for clearance if necessary. 4. Reinstall any accesso- riesremovedin accord with their mounting instructions. Make sure accessories do not in- terferewith shocks throughout full travel. If any accessories bolt to shock mounting points, a careful inspection must be made to insure that they do not bind the shocks in anyway (see figure 2)

Incoming search terms: