HARLEY DAVIDSON SOFTAIL DETACHABLE SADDLEBAG KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 22-03-2011

download
Detachable Saddlebag Configurations Table 1 provides a short description of the detachable saddlebag configurations. Table 1. Softail Detachable Saddlebag Configurations Accessory Configuration (Long Description) Short Descrip- tion Kit 2003-Later FLST/C and 2003-2005 FX Softail Models (Except FXSTD) With Other Detachable Accessories FL Outer 88237-07 2003-Later FLST/C and 2003-2005 FX Softail Models (Except FXSTD) Without Other Detachable Accessories FL Inner 2003-Later FLST/C and 2003-2005 FX Softail Models (Except FXSTD) With Rigid-Mounted Accessories FL Rigid 2006-Later FX Models (Except FXSTD) With Other Detachable Accessories FX Outer 88238-07 2006-Later FX Models (Except FXSTD) Without Other Detachable Accessories FX Inner 2006-Later FX Models (Except FXSTD) With Rigid-Mounted Accessories FX Rigid 2007-Later FXSTC Models With Stock Passenger Upright FXSTC Stock NOTE Proper installation of these kits requires that tasks be completed for one side of the motorcycle first before continuing to the opposite side. Install Turn Signal Relocation Kit Refer to instructions included with Turn Signal Relocation Kit 69857-07. Install Docking Hardware Kit(s) Without Other Detachable Accessories: Refer to instructions included with Docking Hardware Kit 53932-03. With Other Detachable Accessories: Refer to instructions included with Docking Hardware Kits 53932-03 and 88256-07. Install Rear Docking Adapter NOTE This procedure only applies to models without detachable accessories. 1. See Figure 1. Insert rear docking adapter (1) into holes in saddlebag bracket and hold in place. 2. Install rear docking adapter using screw (2) and nut (3). Tighten snugly.

HARLEY DAVIDSON DETACHABLE DYNA SIDEPLATE KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 29-01-2011

download
Additional Parts Required The appropriate docking hardware and possibly a directional relocation kit must be installed prior to installation of this side- plate kit. These kits must be purchased separately from a Harley-Davidson Dealer. Table 1. Docking Hardware Kits Model Year Docking Hardware Kit FXDWG 53964-06 only Table 2. Directional Relocation Kits Model Year Docking Hardware and Directional Relocation Kit All except FXDWG 53961-06 and 53968-06 If mounting this kit with Saddlebags, part number 53968-06 is not required. Loctite® 262 (red), Part Number 94759-99, is available from your Harley-Davidson Dealer. Kit Contents Table 3. Kit Contents Part Number Description (Quantity) 52869-06 Side Plate, detachable, right 52870-06 Side Plate, detachable, left 94592-98 Button head screws (4) SISSYBAR INSTALLATION 2 3 1 4 1 is 01079 1. Sideplate 2. Sissybar 3. Buttonhead screw 4. Rotary latch Figure 1. Detachable Sissybar Sideplate Assembly See Figure 1. Install new or existing sissybar (2) to detachable sideplates (1) using four buttonhead screws (3). Apply Loctite® 262 (red) to screws before installation. Tighten screws to 96- 120 in-lbs (11-14 N-m)

SHOCK CUTAWAY SADDLEBAG INSTALLATION INSTRUCTIONS

0

Filed Under (Tips and Review) by admin on 10-11-2010

download
1. Saddlemen saddlebags mount over the back of the seat or rear fender of most motorcycles. When properly installed there will be one saddlebag on each side of the motorcycle with the split yoke resting on the fender or the seat. Both saddlebags must be securely mounted and tied down in a manner that does not interfere with any part of the motorcycle’s operation. Be certain the saddlebags or their mountings do not contact brake components, turn signals, taillight, brake light, suspension, swingarm, or drivetrain. These Shock Cutaway saddlebags have been designed to fit over your bike’s shock absorbers (see Fig. A), which allow for larger bags on bikes otherwise limited by shock and turn signal location. 2. We highly recommend that your bike be equipped with Saddlemen’s S4 saddlebag supports (see Fig. B) or equivalent. Saddlemen also offers Quick Disconnect rigid-mounting hardware kits for most bikes, that allow easy on, easy off bag installation and eliminate the yoke. For more information, see your dealer or contact Saddlemen at 310- 638-1222. 3. Your saddlebags must be at least two inches away from any exhaust pipe while the motorcycle is stationary or moving. You can adjust the split yoke to change the height of the bag on the motorcycle by adjusting the position of the hook and loop fastening system (Fig. C). Adjust the split yoke shorter to raise the height of the saddlebags, and longer to lower the height of the saddlebags. The split yoke can also be reversed by unbolting each yoke half from each saddlebag, and reversing the yoke’s position on your bike. This allows for the offset in the yoke to be positioned either forward or backwards providing clearance for the motorcycle’s components (Fig. D). 4. In addition to the hook and loop fastener, the bags rely on a nylon safety strap system to ensure proper and secure installation. This strap must be used, and tightened snugly. Assure that the strap’s short end with D-rings is pushed through the slot in the split yoke and resting on the topside it. Once the split yoke is set to the proper position, run the long safety strap over the top of the split yoke and secure it to the D-rings (see Fig E and F), and tighten it. 5. Once you’ve placed the saddlebags on your bike and have them adjusted properly, use the straps located on the bottom of each saddlebag (see Fig. E and G) to connect the saddlebag to the saddlebag support (if you are using Saddlemen’s S4 Saddlebag bracket refer to the instructions shipped with it). These lower straps adjust in length to assure a tight fit. Wrap them around the saddlebag support, snap the buckle halves together, and adjust the length of the strap assuring the strap is tight and supporting some of the saddlebags’ weight. Repeat this step on the other saddlebag.