Harley Davidson KNIGHT PROWLER BELT DRIVE Installation Procedures

0

Filed Under (Harley Davidson) by admin on 28-02-2012

download
STEP 1: Place bike on suitable stand where rear wheel can be rotated in 4th or 5th gear when necessary. STEP 2: Remove front exhaust pipe. If necessary, remove as a one-piece unit. * Tip – Removing front floorboard will help a lot. STEP 3: Using easiest method – bolt cutter, etc. -remove pushrods and discard. We recommend using the S&S Quickee install pushrods and S&S roller tappets WITHOUT travel limiters. Remove tappet covers and tappets. STEP 4: Remove outer cam cover and rotate engine until timing marks are aligned together. STEP 5: Using Harley-Davidson service manual procedure, retract the outer chain tension shoe. STEP 6: Remove crankshaft and crankshaft sprocket retaining bolts using Harley-Davidson service manual procedure and tools. Continue to the next page for special instructions concerning this step with 06-DYNA & CHAIN DRIVE MODELS and also with 1999 THRU 2006 CHAIN DRIVE MODELS

Harley Davidson 1990 and later HSR Choke Cable Installation Manual

0

Filed Under (Harley Davidson) by admin on 28-02-2012

download
The majority of HSR42/45 installations use the Harley cable. Installation is simple when the installation instructions are followed, step by step. Those steps are: • Remove the stock Harley choke cable assembly. • Remove the spring and plunger from the stock cable. • Remove the Mikuni “Starter Nut” from the HSR. • Remove the Mikuni spring and plunger from the HSR. • Install the Mikuni spring and plunger on the Harley choke cable. • Install the Harley choke cable with the fitted Mikuni spring and plunger into the HSR carburetor. • DO NOT use the Mikuni Starter Nut; discard it. • DO NOT use the Harley spring or plunger; discard them. Note: If you do not have installation instructions, you may download them from the www.mikuni.com website in the “manuals” section. If the Mikuni Starter Nut is fitted to the Harley cable, the choke plunger is held off its seat and the choke is open all the time. If the Harley spring and plunger are used, the plunger does not seal and the choke is open all the time. The result, in both cases, is very poor fuel mileage (30 mpg or less). Another possible cause of poor mileage, rough idle and fouled spark plugs is incorrect cable routing. The stock Harley choke cable is very stiff and may not be fully seated in the metal elbow at the carburetor end of its run. This condition is easily corrected. On occasion, one of these errors may have been made by someone else at another location. The unfortunate mechanic who inherits the task of correcting the rich condition, poor idle and poor fuel mileage may have no clue as to the mismatch of parts. For this reason, we include the photos and text to help you discover if your installation is correct.

Incoming search terms:

Harley Davidson Softails Shocks Installation download

0

Filed Under (Harley Davidson) by admin on 28-02-2012

download
Progressive Suspension shocks for your Softail are designed as a direct bolt on replacement for your stockers. Although they are very similar in appearance, they have vastly improved damping and spring rates. Our shocks do not use the remote reservoir system used on earlier model Softail models. 1. Place motorcycle securely on stand or blocks so the rear wheel is slightly off the ground. 2. Per instructions in a authorized shop manual, remove your old shocks. Note location of the mounting hardware. 3. Install the Progressive Suspension shocks using the stock mounting bolts and washers. 4. Tighten all shock mounting bolts to the proper torque specifications (see shop manual for specs) 5. Progressive Suspension shocks have adjustable pre-load to compensate for varying weights. The included wrench or a Harley Davidson pre-load adjustment wrench is necessary to adjust the pre-load setting. Replacement Progressive Suspension, Inc. wrenches are available as Part # SW-784 from most Dealers and Accessory Stores and the Harley Davidson wrench is available as part #94455-89 from any Harley Davidson Dealer. Spring preload is set by us to the lightest setting. To increase preload for heavier riders/loads/passengers, loosen locknut with the inside portion of the supplied wrench or a 1 1/ 16 ” wrench and back it off several turns. Use the supplied wrench or a Harley adjustment wrench to turn the adjustment nut counterclockwise to the desired preload setting. Then tighten the 11/ 16 ” lock nut. Both shocks must be adjusted to the same, equal setting

Incoming search terms:

Harley Davidson Ignition Switch Installation Manual

0

Filed Under (Harley Davidson) by admin on 27-02-2012

download
Ignition Switch a. Harley Davidson i. P/N 71313-96 ii. P/N 71510-93 b. Drag Specialties i. P/N DS-272187 c. JP Cycles i. Cat # 370333 3. Wires and Connectors a. 14 gage wire – Red, 15 inches long b. 14 gage wire – Orange, 15 inches long c. 14 gage wire – Grey, 15 inces long d. 14 gage wire – Brown, 15 inches long e. 14 gage Female Wire Terminals (x3) 4. Miscellaneous a. Radio Shack i. 100 Ohm Resistor (1/4 Watt, 5% Tolerance) – P/N 271-1108 ii. Also recommended – piece of PC board to solder wires and resistor to b. Heat Shrink Tubing – Pack of Assorted Sizes c. Duct Tape or Masking Tape d. 6″ (or longer) Zip (Cable) Ties 2. Nuts and Bolts a. For Switch Mount: i. 4x 6-32 (Chrome or SS) countersink screws ii. 4x nuts for above iii. 4x washers for above b. For Door Locking Mechanism: i. 5/16-18 Bolt (or stud) ii. 2x 5/16-18 nuts iii. Block of rigid material 1. Dimensions: 5/16″ x 9/16″ x 3/8″ 2. Material: Aluminum, Stainless Steel, PVC, etc (Anything rigid will do) iv. 5/16-18 Tap v. Series of drill bits up to 9/32″ (drill size required for 5/16-18 tap) i. Roll (or Spring) Pin and drill bit 1/32″ smaller than pin

Harley-Davidson FL Caliper Mount Installation Manual

0

Filed Under (Harley Davidson) by admin on 26-02-2012

download
Motolight® Caliper mounts are designed to be mounted on the brake caliper mounting boss. Before removing the caliper bolt make certain you have the manufacturer’s recommended torque settings for your make, model and year. 2 . Disconnect your battery. Never work on the electrical system of a motorcycle while the battery is connected. If you’re not sure how, check your owner’s manual, or consider having your dealer install the lights. 3 . Motolights®, like any light, get hot when operating. Do not touch any part of the housing when the Motolights® are in operation and for at least 15 minutes after they have been turned off. 4 . If you are transferring your Motolights® to another bike or have obtained the lights secondhand, it is VERY IMPORTANT that you contact us at 800-567-8346 or 513-474-7530 for new caliper bolts of proper grade and size. Step 1. Unpack the Motolight® system . Take this chance to familiarize yourself with everything. Below is the list of included items: Item # Quantity Description 1 (2) º” x 20 x 5/8″ stainless steel socket head cap screws 2 (2) Housings, aluminum, assembled with lens, lamp and leads 3 (2) Mounting blocks, aluminum, left and right 4 (2) Caliper replacement bolts 5 (2) Lock washers 6 (1) Motolight wiring harness with relay and 20 amp fuse 7 incl. Special Harley auxiliary plug connector in wiring harness (included) 8 (2) Motolight decals (1 helmet size, 1 regular) 9 (1) Aiming tube (cardboard ring) 10 (1) 3/16″ hex wrench 11 (1) Pin wrench (for standard lamp retaining rings-not required for knurled/grooved rings) 12 (15) Cable ties, long and short

2009 Harley Davidson Softail POWER COMMANDER V INPUT ACCESSORY INSTALLATION

0

Filed Under (Harley Davidson) by admin on 26-02-2012

download
1 Remove the seat 2 Uplug the stock wiring harness from the ECM (Fig. A) 3 Remove the 4 nuts that hold the ECM to the bracket and remove the ECM. 4 Remove the bolt that holds the seat strap to the rear fender. 5 Remove the ECM bracket from the fender. Remove one nut at a time or the bracket will fall into the tire. Reinstall the nuts to support the inner fender bracket. Due to the limited amount of room on this bike the seat strap and ECM bracket can NOTbe re-used. 6 Connect the PCVharness in-line of the stock wiring harness and ECM (Fig. B). 7 Place the BLACK PCVto GREYstock connector as close to the fuse box as possible. This connection will NOT lay flat against the frame. 8 Using the supplied velcro secure the ECM to the rear fender. Place the ECM as far down as possible. The upper part of the ECM will just overlap the bolt hole for the seat strap. Make sure to clean both surfaces with the alcohol swab before attaching. If using the Autotune kit offset the ECM about 1″ from center to the right side of the bike. 9 Remove the security module from the top of the battery (Fig. C). This unit slides to the right of the bike.

Incoming search terms:

Harley Davidson FL series Electra Glide, Ultra Classic, Road King, Road Glide Left and Right Mounting Plate Installation Installation Manual

0

Filed Under (Harley Davidson) by admin on 25-02-2012

download
Remove existing control arm end cap and grind the outside flush. See picture below for reference. The swing arm will drop if both sides are removed at the same time. To ease installation, complete one side before starting on the other. Note: there is a left and right. Left and right end caps shown. 2. Install mounting plate assembly 10002351 on top of the end cap using 7/16″ hex head bolt and lock washer in the bottom hole. Use the 7/16″ counter sink bolt in the top hole. Make sure the end cap is seated properly. The end cap notch should fit into the recess on the frame. The pivot arm assembly is shipped on mounting plate assembly; you may remove the pivot arm to make installation easier. 3. Snug up the bolts evenly, make sure the end caps are not crooked in relation to the frame. Tighten both bolts to 25 ft lbs. (Further tightening will be required after the toe in is set). 4. If you removed the left hand pivot arm assembly, remount it now, 10002575-A (pg 20) with seal, bearings (2), washer, nut, cotter pin and dust cover. 5. Repeat for right hand side. 5 Toe In Adjustment Adjustment made with the mounting plates, bolts, pivot arms, and hubs (without wheels and tires) in place

Incoming search terms:

HARLEY DAVIDSON DYNA SIDESHOTS BLACK INSTALLATION AND REMOVAL PROCEDURE

0

Filed Under (Harley Davidson) by admin on 25-02-2012

download
Remove seat to gain access to rear oxygen sensor connector. Unplug sensor and feed end of wire through frame so that it is free from motorcycle. NOTE: Pay attention to wire routing for re-installation. 2. Remove two bolts holding rectifi er onto front of frame (near front tire). Open plastic cover to gain access to front oxygen sensor connector. Unplug sensor from harness. Remove cable tie holding wire to frame and feed end of wire through so that it is free from motorcycle. 3. Loosen heat shield clamps on both the front and rear head pipes. 4. Remove two cylinder exhaust port fl ange nuts from each head pipe, located at the cylinder head. 5. Remove front head pipe clamp bolt. 6. Remove the bolt that attaches muffl ers to the frame mounting bar. 7. Remove the complete exhaust system and set aside. Assistance may be required. 8. Remove stock mounting bar and the studs in the transmisson cover. Save the bolts, one will be re-used. 9. Remove left bolt below the transmission cover. Position mounting bracket 405-P over mounting location to determine which bolts to remove (Figure 1). Install this bolt in the top hole left vacant by the new bracket. 10. Carefully remove the fl anges and circlips from the stock exhaust system using snapring pliers. NOTE: Replace bent or damaged circlips. Check condition of stock exhaust gaskets. Replace if worn or damaged. (Recommended replacement exhaust port gaskets, Screamin’ Eagle part number 17048-98)

Harley Davidson Fork Lowering Kit Installation And removal Instruction

0

Filed Under (Harley Davidson) by admin on 24-02-2012

download
1. Remove and disassemble forks (including removal of damper rod) according to steps outlined in an authorized service manual for your particular model and year Harley Davidson (see figure 1 for reference). 2. To achieve a one inch (1″) lowered height, leave the stock top out spring on the damper rod and install one Progressive Suspension top out spring on the damper rod with the stock top out spring (see figure 2). Proceed to step 4. 3. To achieve a two inch (2″) lowered height, leave the stock top out spring on the damper rod and install two Progressive Suspension top out springs on the damper rod with the stock top out spring (see figure 3). 4. Reinstall damper rods into forks per shop manual. A. Add the proper amount of fork oil as recommended in your shop manual. Make sure the viscosity is the recommended weight. B. Install your Progressive Suspension fork springs with the close wound end up

Harley Davidson sound system Installation Manual

0

Filed Under (Harley Davidson) by admin on 24-02-2012

download
unplug factory radio harness. 2. Plug in Bazooka fast harness into radio and plug factory harness into Bazooka fast harness. ( Fig. 2-1 ) 3. Run red power wire to battery leaving fuse block with the factory fuses. Make sure fuse is removed during install Attach ground wire to triple tree ground terminal. Left side cover. ( Fig. 2-1) 4. Replace factory speakers. All speakers are shipped with grills and in some cases rubber magnet covers. These are for shipping protection only. If rubber magnet covers are on the speakers, they MUST be removed prior to installation. Discard the grills and use the OEM grills to complete the installation. 5. The front and rear speakers are the same. The front speakers must be slid into the speakers mounts with the crossover network placed toward the outside of the fairing and the speaker terminals to the inside for ease of installation. When mounting the rear speakers you must use the spacers provided. Place spacer on the speaker enclosure. Then the speaker and the grill last. The rear speakers should be mounted with the crossover network toward the rear of the bike.

Incoming search terms: