HARLEY DAVIDSON CHROME SADDLEBAG COVER WINGTIP TRIM KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 15-03-2011

download
Installation NOTE The following procedures can be performed with the saddlebags on or off of the motorcycle, and the covers on or off of the saddlebags. Figures show saddlebag covers removed. 1. Open the saddlebags and remove all loose contents. 2. Thoroughly clean the left and right saddlebag covers, and let them dry completely. 3. See Figure 2 for your saddlebag material. Position a straightedge against the check strap mounting posts of one of the covers, and mark or scribe a guide line along the straightedge as shown. NOTE When applying the templates in the following steps, make sure the templates are aligned as instructed, and the respective “LEFTSIDE” or “RIGHTSIDE” lettering is clearly readable when applied to the applicable (left or right side) cover. The templates are designed to be easily removed from the first cover and re-applied to the remaining cover When applying the templates, ensure that each template is correctly positioned BEFORE drilling the first hole

HARLEY DAVIDSON LIGHTED CHROME DIRECTIONAL BAR INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 15-03-2011

download
INSTALLATION 1. Disconnect turn signal wires at connectors located in directional bar. On 1994 and later models there are two wires for each turn signal lamp. Earlier models have only 1 wire per lamp. 2. Remove existing directional bar from motorcycle. Save all hardware for reattachment. If the turn signal connector is too large to be removed from the directional bar, remove the wires from the connector as follows: Bend back the connector latches on the sides of the connector slightly to free the secondary lock. Rotate the secondary lock outward on hinge to access terminals in chambers of connector housing. With a paper clip sharpened to a chisel point, insert the paper clip into the connector housing cavity until it stops. Pivot the end of the paper clip and gently tug on the wire to pull the terminal from the cavity. Do not tug on the wire until the tang that holds the terminal in the cavity is released. Take your time, a few tries may be required before you develop a feel for releasing the terminal from the connector. 3. Remove screws that mount turn signals lamps to existing directional bar. Remove lamps and turn signal wires (with their attached connector halves) from existing bar. 1 2 3 4 is02199 1. Ground wire 2. Hold lamp in place 3. Backing plate 4. Self-tapping screw Figure 1. Remove Backing Plate 4. See Figure 1. For each end of new directional bar, remove self-tapping screw that holds corner of backing plate and ground wire in place and remove backing plate. 1 2 is 02200 1. Hold lamp in place with this screw 2. Turn signal connector(s) are behind LED Figure 2. Assembling Directional Bar 5. See Figure 2. For each end of bar, place turn signal lamp in position with wires routed as shown. Move LED light out of the way and thread 5/32 inch Allen socket screw into lamp to hold lamp in place. Tighten screw.

HARLEY DAVIDSON PASSENGER FOOTBOARD INSERT KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 15-03-2011

download
INSTALLATION If replacing an insert or inserts on a vehicle currently equipped with Swept Wing Passenger Footboards: Existing Footboard Insert Removal NOTE Carefully remove the currently installed footboard insert to avoid damage to chrome surfaces. 1. See Figure 1. Fold the passenger footboard (1) into the UP position. 2. Loosen, but do not remove the footboard insert setscrew (2). 3. With the footboard folded DOWN, carefully raise an outside corner of the existing insert with a suitable flat-bladed tool, taking care to avoid damaging the chrome footboard pan. 4. Continue around the insert, using a second tool if necessary to pry the existing insert (3) from the footboard pan. 5. If replacing both inserts, repeat for the opposite footboard. Swept Wing Passenger Footboard Installation 1. If installing inserts on a vehicle NOT currently equipped with Swept Wing Passenger Footboards: •Remove currently installed passenger footboards (if so equipped) per the instructions included with the Swept Wing Passenger Footboard Kit. •Remove currently installed passenger footpegs (if so equipped) by removing the socket screw with lockwasher retaining the footpeg support bracket to the rear fork (swingarm) bracket. 2. Follow the instructions in the Swept Wing Passenger Footboard Kit to install the passenger footboards. Footboard Insert Installation 3. ALL applications: Center the two footboard pivot pins. 4. Use soapy water to moisten the rubber dowel pins and pivot pin slots on the bottom of the new footboard insert. 5. Place the insert into position with the rubber dowel pins mating the holes in the footboard pan. Firmly press the insert into the footboard until the dowel pins pop into place. 6. Fold the passenger floorboard UP and tighten the setscrew to secure the insert. 7. Repeat Steps 3 through 6 for the opposite footboard. NOTE Avoid the contact of chrome surfaces with abrasive materials (stones, sand, etc.) as damage will result

HARLEY DAVIDSON SOFTAIL CUSTOM SEAT KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 15-03-2011

download
Kit Contents See Figure 3 and Table 2 for complete kit contents. See Table 1 for the grab strap part number associated with each seat kit. Table 1. Kit Numbers and Grab Strap Usage Grab Strap Kit Number 51332-07 51310-07 51910-08 51936-08 51701-06 51308-07 51365-07 51367-07 51387-06A 51388-06 51389-06 51390-06 51391-06 51392-06 51398-07 51365-07 51410-08 51411-08 51412-08 51414-08 51415-08 51416-08 51407-08 The rider’s safety depends upon the correct installation of this kit. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley- Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00308a) INSTALLATION NOTE When performing the following procedures, avoid scratching painted surfaces (fender, tank, etc.) with tools or metal seat tabs. FXST, FXSTB and FXSTS Models 1. See Figure 3 and Table 2. Unscrew the captive thumbscrew fastening the back of the original equipment (OE) seat to the vehicle. 2. Pull the seat slightly to the rear to disengage the tang at the front of the seat from the motorcycle frame. 3. Lift the front of the seat while pulling the seat carefully forward to remove the seat from the vehicle. 4. Remove the OE grab strap and attaching hardware. Save the hardware for later use. 5. Install the grab strap. See either “For Kit 51936-08″ or “For All Other Kits” to install the grab strap. 2007 and Later FLSTF Models 1. Remove original equipment (OE) seat and mounting hardware following the instructions in the Owner’s Manual. 2. Remove and discard the OE grab strap and attaching hardware. 3. See Figure 3. Install two flange nuts (9) from the kit onto the OE grab strap mounting studs (as shown in Figure 1, Item 1). 4. Install the grab strap. See either “For Kit 51936-08″ or “For All Other Kits” to install the grab strap.

HARLEY DAVIDSON CRUISE CONTROL KIT FOR FLHR/I AND FLHRS/I MODELS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 15-03-2011

download
INSTALLATION 1. Remove seat, left saddlebag, left side cover and air cleaner assembly following instructions in applicable Service Manual. 2. Review the CRUISE CONTROL-ULTRA MODELS section in the applicable Service Manual before attempting to install this kit. Install Cruise Control Module To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 1. Refer to the appropriate Service Manual and remove bat- tery. 1 is04799 1. Cruise control module mounting hole (3) Figure 1. Battery Box (Right Side View) 2. See Figure 1. In battery box, identify the location of the three mounting holes (1) (on left side of panel) for mounting the cruise control module. 3. See Figure 10. Obtain the cruise control module (1) with cruise cable attached and three grommets (5) from kit. Install the grommets on studs of cruise control module with small diameters outward. 4. See Figure 2. While holding cruise control assembly in place near its mounting location, feed the cruise control cable through the hole in frame crossmember plate and route under rear spark plug wire staying on inner side of fuel line components. Carefully curve cable toward the right and continue routing up under the fuel tank and over the top of the engine stabilizer bracket, then down between cylinder heads. Leave in place temporarily. 5. See Figure 10 and obtain a harness retainer (4) from kit and secure the cruise cable to crossmember plate with barb as shown. On California models, remove the EVAP hose from cable clip and secure hose with one of the cable strap (8)

Incoming search terms:

HARLEY DAVIDSON SCRIPTED HAND LEVER EMBLEMS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 13-03-2011

download
General Kit 44514-02 is designed for installation on hand lever control kit 45533-02, all other emblem kits are designed for installation on hand lever control kit 45459-02. Installation NOTE When installing the emblems, make sure text is positioned properly. 1. Clean bonding surface on levers with isopropyl alcohol. 2. Remove backing, carefully position emblem and apply steady, even pressure for at least five seconds. 3. Allow 24 hours for adhesive to fully cure

HARLEY DAVIDSON FXSTD DETACHABLE WINDSHIELD AND DOCKING HARDWARE KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 13-03-2011

download
INSTALLATION NOTE Use the Docking Hardware Kit to assemble two upper and two lower clamps. See the Service Parts illustration. The upper clamps use a mounting pin (4) and the lower clamps use a button head screw (5) to fasten the windshield mounting bushing. 1. Assemble the windshield docking hardware as follows: a. Install a larger chrome washer (6) and bushing (7) onto a button head screw (5). Thread the screw into the boss on one of the clamps (1), and tighten finger tight. Repeat for a second lower clamp. b. Install a larger chrome washer (6) and bushing (7) onto a mounting pin (4). Thread the pin into the boss on one of the clamps (1), and tighten finger tight. Repeat for a second lower clamp. 2 1 3 4 4 5 is 02187 1. Upper clamp 2. Lower clamp 3. Fork tubes 4.1/8 inch (3 mm) approximately 5.3.0 inch (76 mm) Figure 1. Installing Clamps NOTE Place shop rags on the headlamp, front fender and front of the fuel tank to prevent scratches to these components. Be sure the windshield assembly does not contact chrome or painted parts. Contact will cause scratches to chrome or painted parts. 2. See Figure 1. Install a lower clamp onto a fork tube using a smaller chrome washer and lock nut from the kit. Adjust so the clamp is approximately 1/8 inch (3 mm) from the top of the lower triple clamp, then finger tighten the lock nut. Repeat with the second lower clamp and fork tube. NOTE Keep front wheel straight to prevent brackets from scratching fuel tanks. See Figure 1. Install the clamps on the fork tubes so the bushing center lines are 3 inches (76 mm) apart. 3. Install an upper clamp onto a fork tube using a smaller chrome washer and lock nut from the kit. Adjust so the clamp is approximately 1/8 inch (3 mm) from the bottom of the upper triple clamp. Ensure that the center lines of the upper and lower bushings are 3 inches (76 mm) apart, then finger tighten the lock nut. Repeat with the second upper clamp and fork tube

HARLEY DAVIDSON FRONT SPOILER KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 13-03-2011

download
Installation NOTE The spoiler in kit number 58882-04BDK is finished with a primer coat. Before installation, have the spoiler painted 1. Mount the motorcycle on a lift table. 2. See the Service Parts illustration. Attach the upper front spoiler bracket (4) to the bosses on the inside front of the spoiler (1) with the two Hi-Lo screws (10) from the kit. Tighten to 15-20 in-lbs (1.7-2.3 Nm). 3. Attach the lower front spoiler bracket (5) to the two weld nuts in the cross bar at the bottom front of the motorcycle frame with two hex head machine screws (6) and split lockwashers (7) from the kit. Torque to 30 ft-lbs (41 Nm). 4. Remove the protective film from the back of the medallion. Carefully center the medallion on the recessed area on the front of the spoiler. 5. Press the Bar and Shield medallion (3) firmly into position. Hold the medallion in place, pushing hard with your thumbs, for about five seconds. Take care not to shift the medallion on the spoiler. 6. After releasing pressure, avoid direct contact with the medallion for about 20 minutes. 7. Place a flat washer (9) on one of the pan head machine screws (8) from the kit. Position the spoiler to the front of the frame. Insert the screw through the large hole in the bottom of the spoiler and thread it into the upper front spoiler bracket, but do not fully tighten at this time. 8. Place a flat washer on each of the two remaining pan head machine screws from the kit. Insert the screws through the slots in the bottom of the spoiler and thread them into the lower bracket, but do not tighten fully. 9. Position the spoiler next to the vehicle frame allowing an equal amount of minimal clearance. Alternately tighten the three screws to 72 in-lbs (8 Nm)

HARLEY DAVIDSON XL STARTER MOTOR COVER INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 13-03-2011

download
Installation 1. Remove exhaust system according to Service Manual instructions. 2. See Figure 1. Remove the outer primary screw shown and retain it for reinstallation. 3. See Service Parts Illustration. Insert the thread cleaning screw (9), through the primary cover and the crankcase until the full screw diameter protrudes through the crankcase. Remove any debris from from the tip of the thread cleaning screw. Remove thread forming screw and discard. NOTE If thread cleaning screw binds in crankcase hole, remove thread cleaning screw and chase threads with 1/4 – 20 tap. 4. Install set screw (8) from outer primary side using the wrench provided. Set screw should extend past the crankcase approximately .375″. 5. With wrench in set screw to prevent rotation, install the backplate over the set screw and fasten with the 1/4-20 nylock nut (5). 6. Reinstall the primary cover screw saved in Step 1. Torque to 80-110 in-lbs (9-12 Nm). 7. Remove the the oil hose clamp from the starter stud. Do not remove the clamp from the hoses. 8. Replace the original equipment starter stud with stud (7) provided. Torque to 39-65 in-lbs (4-7 Nm). 9. Install bracket (2) over stud (7) and fasten with #10-24 nylock nut (6). Rotate bracket until the tab on the bracket rests on starter motor. 10. Install oil hose clamp onto bracket (2) using one of the #10-24 screws (4). Tuck the hoses down as far as possible without contacting the drive belt or kinking the hose. Contacting the drive belt or kinking the hose may cause damage to the hoses or powertrain. 11. Install the cover (1) to the backplate (3) and bracket (2) using four of the #10-24 screws (4) with the wrench provided. The cover should fit inboard of the gear cover and partially on top of the sprocket cover. Start the bracket screw first, then follow with the (3) backplate screws. 12. Reinstall exhaust system according to Service Manual Instructions

HARLEY DAVIDSON LOW REAR SHOCK KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 13-03-2011

download
See Figure 3 and Table 1. INSTALLATION Shock Absorbers Perform this installation when the engine is cool. Working on or near the exhaust system when the engine is hot could result in severe burns. (00311a) Installation of any accessory suspension components can affect cornering clearance. This could distract the rider, causing loss of control and death or serious injury. (00431b) NOTES This procedure requires that both shocks be removed prior to installing the new shock absorbers. You need to place the motorcycle on a center stand with the rear wheel raised off of the ground. The jiffy stand should be able to move through its full range of travel. The exhaust system may interfere when removing and installing the lower right shock mounting hardware. If necessary, see Service Manual and remove the rear exhaust pipe. 2 4 5 7 1 6 3 is05206 1. Lower screw 2. Upper screw 3. Lower washer 4. Upper washer 5. Cover 6. Nut 7. Shock absorber Figure 1. Remove / Install Shock Absorber 1. Block the motorcycle under the frame so that the motorcycle is securely resting upright, the jiffystand may be moved through its full range of travel, and rear wheel is just off the ground. 2. Remove the lower shock mounting screw (1), washer (3) and nut (6) from the shock absorber (7). Save the hardware for reuse. 3. Remove the upper bolt (2), washer (4) and cover (5) and remove the shock absorber. Save the hardware for reuse. 4. Repeat Steps 1 and 2 for opposite side and save the hardware. 5. Apply 2-3 drops of LOCTITE 243® (blue) on the threads of the lower mounting bolt, then install bolt, lower washer and nut to the shock. 6. Apply 2-3 drops of LOCTITE 243® (blue) on the threads of the upper mounting bolt, then install the shock cover, upper mounting bolt and washer to the shock. Verify the cutout in shock cover locates properly

Incoming search terms: