HARLEY DAVIDSON FAT HANDLEBAR RISER KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 22-03-2011

download
INSTALLATION NOTES The upper cup washer (A) must be oriented with the flat side up and the lower cup washer (D) with the flat side down. See Figure 1 for the following procedure. 1. Align the components as shown, and install the risers (2) to the upper fork bracket. The ground wire (G) and the internal tooth lock washer (H) are located on the right side only. Do not tighten the riser mounting screws (I) at this time. 2. If an appropriate Harley-Davidson 1-1/4 inch handlebar has not been installed, install one according to the Instruction Sheet included with the kit, or re-install the handlebar assembly onto the risers. 3. Loosely install riser caps (1) onto the handlebars and risers using four socket head screws (3) as shown. 4. Ensure that the risers stay properly aligned with the handlebar and tighten the riser mounting screws (I) to 50-60 ft-lbs (68-81 Nm) . 5. Adjust handlebar to the desired position, ensure that it is centered on the risers, then, starting with the front screws, tighten the four socket head screws (3) to 12-15 ft-lbs (16- 20 Nm) . 6. Turn the handlebars full right and left. Check that: •The handlebars and triple tree clamps do not contact the fuel tank. •The steering stops function properly. •The wiring and brake line are not pinched or kinked in the steering assembly. •Throttle returns from full open to close at both fork stops. Install proper length brake lines. Incorrect brake line length can adversely affect motorcycle operation, which could cause loss of control resulting in death or serious injury. (00325a) •If you are installing different handlebars, measure the change in distance that will be required from the end of the stock brake line to the brake master cylinder. •Compare this revised length to the brake line provided in your kit. •If the line is more than 2.0 in. (50.8 mm) longer or more than 1.0 in. (25.4 mm) shorter than the above measured distance, see a Harley-Davidson dealer for the correct brake line length

HARLEY DAVIDSON HARDWARE/ TURN SIGNAL RELOCATION KIT FOR SPORTSTER LEATHER SADDLEBAG KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 17-03-2011

download
Installation Instructions for 79052-04 and 79073-04 Do not exceed 7 lbs (3.17 kg) maximum load in each saddlebag. Additional weight can affect a motorcycle’s stability, handling characteristics, and safe operating speed which may lead to an accident resulting in death or serious injury. NOTE A pick tool (Snap-on TT600-3) will be required for 1996 and later models for removing and reinstalling a multi-lock amp con- nector. NOTE A Service Manual for your vehicle is available from your Harley- Davidson Dealer. Installation – Hugger Models Only (1994-1997) To perform the following steps for Hugger Models only, fender and frame must be sufficiently supported, as both shocks will need to be removed at the same time. An improperly supported vehicle could result in death or serious injury. A Service Manual is needed to install this kit. The rider’s safety depends upon the correct installation of this kit. If the procedure is not within your capabilities or you do not have the correct tools, have your Harley-Davidson Dealer perform the installation. Improper installation of this kit could result in death or serious injury. To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative cable first) before proceeding. Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 1. Remove seat, sissy bar and sideplate, if applicable. Retain hardware for reinstallation. Disconnect battery, negative cable first. 2. Properly support motorcycle under frame to prepare for removal of right and left shocks. 3. Remove rear buttonhead screw on each side of fender. 4. See Figure 1. With rear fender and frame securely supported, remove left and right shocks by removing upper nut (2), washer(s) (3) and shock cover (4). Remove bolt (6), washer (7) and locknut (8) at lower shock mount. Remove shock

HARLEY DAVIDSON SOFTAIL CUSTOM SEAT KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 15-03-2011

download
Kit Contents See Figure 3 and Table 2 for complete kit contents. See Table 1 for the grab strap part number associated with each seat kit. Table 1. Kit Numbers and Grab Strap Usage Grab Strap Kit Number 51332-07 51310-07 51910-08 51936-08 51701-06 51308-07 51365-07 51367-07 51387-06A 51388-06 51389-06 51390-06 51391-06 51392-06 51398-07 51365-07 51410-08 51411-08 51412-08 51414-08 51415-08 51416-08 51407-08 The rider’s safety depends upon the correct installation of this kit. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley- Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00308a) INSTALLATION NOTE When performing the following procedures, avoid scratching painted surfaces (fender, tank, etc.) with tools or metal seat tabs. FXST, FXSTB and FXSTS Models 1. See Figure 3 and Table 2. Unscrew the captive thumbscrew fastening the back of the original equipment (OE) seat to the vehicle. 2. Pull the seat slightly to the rear to disengage the tang at the front of the seat from the motorcycle frame. 3. Lift the front of the seat while pulling the seat carefully forward to remove the seat from the vehicle. 4. Remove the OE grab strap and attaching hardware. Save the hardware for later use. 5. Install the grab strap. See either “For Kit 51936-08″ or “For All Other Kits” to install the grab strap. 2007 and Later FLSTF Models 1. Remove original equipment (OE) seat and mounting hardware following the instructions in the Owner’s Manual. 2. Remove and discard the OE grab strap and attaching hardware. 3. See Figure 3. Install two flange nuts (9) from the kit onto the OE grab strap mounting studs (as shown in Figure 1, Item 1). 4. Install the grab strap. See either “For Kit 51936-08″ or “For All Other Kits” to install the grab strap.

HARLEY DAVIDSON FRONT TYPHOON WHEELS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 11-03-2011

download
If installing kit 44615-08, 40774-10, 44657-08 or 43300053 on a Dyna model with stock laced wheels, the separate purchase of stock brake disc (44553-06A) or polished brake disc (41500012) is required. The following Harley-Davidson Genuine Motor Accessories are recommended for proper maintenance and cleaning: •Harley® Bright™ Chrome Cleaner (94683-99) •Harley® Glaze™ Polish and Sealant (99701-84) •Harley®Wheel and Spoke Brush (43078-99) •Harley-Davidson®Wheel and Tire Cleaner (94658-98) •Harley® Preserve™ Bare Aluminum Protectant (99845-07) Touch-up paint for painted wheels is available from a Harley- Davidson dealer: •Touch-Up pen, wheel, black (94482) The rider’s safety depends upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333a) NOTE This instruction sheet references service manual information. A service manual for your model motorcycle is required for this installation and is available from a Harley-Davidson Dealer. 1 2 is06470 1. Closed brake disc 2. Open brake disc or floating rotor Figure 1. Front Brake Disc Styles Table 1. Front Disc Hardware Fitment Hardware Brake Disc 5 Stock disc screws (3655A) Closed disc Chrome screw kit (46646-05) includes 5 screws 5 Stock disc screws (3762M) and 5 disc washers (6966M) Open disc NOTE: Models equipped with dual front brakes and models being equipped with a wheel with dual brake mounting surfaces require twice as many screws/washers (10 total screws or 2 chrome screw kits if available). INSTALLATION NOTE Use plastic protectors on tire mounting tools and rim clamps when mounting a tire to a painted wheel. For wide low profile tires a tire mounting machine with a second arm to press down on the sidewall while the wheel is rotating is recommended.

HARLEY DAVIDSON ADVANCED AUDIO CB RADIO KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 11-03-2011

download
2006 models: communication switch 77173-06 2007 models: communication switch 77173-07 2008 models: communication switch 77173-08 FLHT models will require prior installation of: •Advanced Audio AM/ FM/ CD Radio Kit (76412-06) •AM/ FM Antenna Kit (76325-06 or 76317-06) Unless one has already been fitted as part of another Advanced Audio kit installation: 2006-2007 FLHX models will require the separate purchase of: •fuel tank console (61270-98A), •tank console gasket (71294-89), •a button-head screw (3652), •nut (7964) •clip (10103 and 10120). •tank pod mounting screws (2462) quantity 3 •FLHT trim piece (52447-96) and cb pod trim badge 2008 FLHX models: •fuel tank console (61270-08) •clips (10103 and 10120) NOTE The console screws, fuel door, gasket, mounting bracket will all need to be reused. FLTR models will require the separate purchase of: •a Console Pod Assembly (77136-03), and •three pan-head screws (2462). NOTE See a Harley-Davidson dealer for availability of optional decorative inserts for the Console Pod Assembly. ALL models will require the additional purchase of: •a Non-Ultra Overlay Harness (70169-06), and EITHER : •a Premium Stereo Helmet Headset (77147-98) OR a Hand-Held CB Microphone Kit (76312-98), All of these items are available from a Harley-Davidson Dealer. If two modules are already installed on top of the radio, two Dual-LockTM mounts, (76434-06), will be needed. Models WITHOUT a Tour-Pak installed will require the additional purchase of a Frame Mount CB Antenna Kit (76415- 06). Models WITH a Tour-Pak installed will require the additional purchase of a Tour-Pak Mount CB Antenna Kit (76414-06). All of these items are available from a Harley-Davidson Dealer. The rider’s safety depends upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333a) NOTE This instruction sheet references Service Manual information. A Service Manual for your model motorcycle is required for this installation and is available from a Harley-Davidson Dealer. Electrical Overload It is possible to overload your motorcycle’s charging system by adding too many electrical accessories. If your combined electrical accessories operating at any one time consume more electrical current than your vehicle’s charging system can produce, the electrical consumption can discharge the battery and cause vehicle electrical system damage. See a Harley-Davidson dealer for advice about the amount of current consumed by additional electrical accessories, or for necessary wiring changes. (00211b)

Incoming search terms:

HARLEY DAVIDSON REAR ROAD WINDER WHEELS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 11-03-2011

download
This instruction sheet references service manual information. A service manual for your model motorcycle is required for this installation and is available from a Harley-Davidson dealer. Kit Contents See Figure 1 and Service Parts Tables. INSTALLATION 1. Remove existing rear wheel assembly. Save axle, axle nut, brake disc and wheel spacers for kit installation. Refer to the service manual. NOTES Prior to removing or installing the wheel, the rear brake caliper must be removed. The cotter pin or spring clip for the axle nut must be replaced. They are available for purchase from you dealer. See your dealer for the correct part number for your model motorcycle. Do not re-use brake disc screws. Re-using disc screws can result in torque loss and damage to rotor and/or brake assembly. (00319b) Do not re-use sprocket mounting screws. Re-using sprocket mounting screws can result in torque loss and damage to the sprocket and/or belt assembly. (00480b) 2. See Figure 1. Install valve stem assembly (E) on wheel. Refer to the service manual. 3. Assemble wheel installation kit components, stock brake disc, and sprocket to wheel using the appropriate service parts table. Refer to the service manual. NOTES Install the primary bearing first using appropriate service manual and WHEEL BEARING REMOVER/INSTALLER. The machined grooves in the hub face indicate the primary bearing side. 4. Install rear wheel (1), stock axle and stock spacers to motorcycle. Refer to the service manual. MAINTENANCE AND CLEANING Chrome parts must be maintained regularly to keep their original shine and luster. 1. Clean heavily-soiled wheel surfaces using Harley-Davidson Wheel and Tire Cleaner, applied with Harley Wheel and Spoke Brush. 2. Thoroughly clean chrome with a good quality chrome cleaner, such as Harley Bright Chrome Cleaner. 3. After cleaning and polishing, seal the finish with a good quality sealer, such as Harley Glaze Polish and Sealant

Incoming search terms:

HARLEY DAVIDSON DETACHABLE QUARTER FAIRING AND DOCKING HARDWARE KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 10-03-2011

download
Installation The rider’s safety depends upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley- Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333a) NOTE If your motorcycle has directional lights mounted on the upper fork bracket they must be relocated to the bottom fork bracket. Some models have front directional lights equipped with three wires, the third black wire is a ground wire. Check to determine how many wires are connected to the front directional lights and follow the following procedure that applies. Ifdirectional lights are not mounted on the upper fork bracket proceed to “ASSEMBLING FAIRING”. Relocating Two Wire Directional Lights 1. Support motorcycle on a center stand such that front wheel is raised slightly off the ground. 2. Remove fork tube pinch screw from right side of lower bracket. 3. Cut wires connected to right directional light about 2 in. away from directional light body. 4. Remove fork tube pinch screw from right side of upper fork bracket. (This is the screw that secures the right directional light.) 5. Install right directional light on right side of lower fork bracket using pinch screw removed in step 4. Install pinch screw removed in step 2 into right side of upper bracket. Tighten both pinch screws to 30-35 ft-lbs. 6. Repeat steps 1 through 5 to relocate left directional light. NOTE Fork tubes may slide downward within fork brackets. If this occurs, front fork tube extension above front fork upper bracket will have to be readjusted according to appropriate Service Manual procedures. 7. Connect the right directional light as follows: Strip approx. 5/16 in. of insulation from the wires cut in step 3. 8. Crimp solderless connectors from kit on two wires coming from motorcycle. 9. Split one end of the 2-conductor polarized wire from kit back about 2 in. and strip 5/16 in. of insulation from wire ends. 10. Slide a piece of shrink tubing from kit over each of the wire ends stripped in step 9 and crimp the wires into the terminals installed in step 8. Make sure you connect the silver and copper colored wires to like colored wires. NOTE Polarized wire is used in this application to ensure correct wiring. One wire is silver, one is copper colored. Wire colors of spliced wire must match wire color of original directional wire leads. 11. Cut polarized wires to the length required for connection to the wires at the relocated directional light. Make certain you leave enough slack in wires to allow routing the harness along the fork tube. 12. Split remaining end of the 2-conductor polarized wire from kit back about 2 in. and strip 5/16 in. of insulation from wire ends. 13. Slide heat shrink tubes over the two wire end. 14. Strip 5/16 in. of insulation from wires connected to directional light and connect like colored wires at directional light with connectors from kit. 15. Slide heat shrink tubing over connectors installed in steps 10 and 14. Activate shrink tubing with heat gun or hair dryer.

HARLEY DAVIDSON TIMKEN BEARING CONVERSION TOOL INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 10-03-2011

download
2-ton press (must be square to within .010″, ram to table) Inch-lb torque wrench Foot-lb torque wrench T15 TORX® drive socket (for inch-lb torque wrench) 5/32 inch hex drive socket (for inch-lb torque wrench) 5/16 inch hex drive socket (for foot-lb torque wrench) 5/64 inch hex key wrench 1/16 inch hex key wrench 3/8 inch drive hand drill small tap handle (suitable for #8-32 tap) Tapping Fluid Press Fit Lube (non-drip) Loctite® 620 threadlocker and sealant The rider’s safety depends upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333a) NOTE This instruction sheet references service manual information. A service manual for your model motorcycle is required for this installation and is available from a Harley-Davidson Dealer. Kit Contents See Figure 21 and Table 3. If replacement parts are needed contact JIMS® at 805-482- 6913 or INSTALLATION 1. Remove and disassemble the engine as necessary to remove the left side engine case. Bearings and seals must be removed from the left case. Refer to the service manual for the disassembly procedures. 2. Use an appropriate solvent to clean the left engine case. Also clean the bearing sleeve (1) supplied in the kit. 3. Apply Loctite 620 to the smaller inside diameter portion of the left case bearing bore. 4. See Figure 1. Apply Loctite 620 using a cotton swab to the smaller portion of the outside diameter (2) surface of the bearing sleeve (1). 5. Apply a spare amount of non-drip press fit lube (3) to the larger outside diameter of the bearing sleeve. 6. See Figure 2. Fit the bottom locater plate (1) to the to the outside of the case over the bearing bore. The word “BOTTOM” will be at the bottom of the case when installed at the 6 o’clock position

Incoming search terms:

HARLEY DAVIDSON CHROME 1.25 INCH (31.75 MM) DIAMETER HANDLEBAR KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 10-03-2011

download
CHROME 1.25 INCH (31.75 MM) DIAMETER HANDLEBAR KIT GENERAL Kit Number 56032-08 Models For model fitment information, see the P&A retail catalog or the Parts and Accessories section of www.harley-davidson.com (English only). This kit does not fit models equipped with a hydraulic clutch, handlebar mounted gauges or the Road Tech® Radio. Additional Parts or Accessories Required Separate purchase of additional parts or accessories is required for proper installation of this Handlebar Kit on this model motorcycle. Please see the P&A retail catalog or the Parts and Accessories section of for a list of required parts or accessories for this model. For Australia, Brazil, England, Europe and Japan, two special screws (Part Number 2935A) will also be required. Tools and Supplies Required Loctite® 271 Threadlocker and Sealant – Red (H-D Part Number 99671-97) is required for the proper installation of this kit. Fresh, uncontaminated DOT 4 brake fluid from a sealed container will also be needed. Replace brake line gaskets. Re-using original gaskets can cause brake failure and loss of vehicle control, which could result in death or serious injury. (00318a) For models that retain the original brake line, the two brake- line gaskets found at each banjo fitting must be replaced . Refer to the appropriate parts catalog or see a Harley-Davidson dealer for the correct part numbers. Motorcycles equipped with a glued left-side hand grip will also require a new grip, sold separately. Refer to the parts catalog for replacement stock hand grips. Ask a Harley-Davidson dealer about the selection of Genuine Motor Accessory hand grips that are available. The rider’s safety depends upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333a) NOTE This instruction sheet references service manual information. A service manual for this year and model motorcycle is required for this installation and is available from a Harley-Davidson dealer. Kit Contents See Figure 6 and Table 1. INSTALLATION Preparation To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative (-) cable first) before proceeding. (00307a) Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 1. Refer to the service manual and follow the instructions given to remove the seat and disconnect the battery cables, negative cable first. Retain all seat mounting hardware. Direct contact of D.O.T. 4 brake fluid with eyes can cause irritation. Avoid eye contact. In case of eye contact flush with large amounts of water and get medical attention. Swallowing large amounts of D.O.T. 4 brake fluid can cause digestive discomfort. If swallowed, obtain medical attention. Use in well ventilated area. KEEP OUT OF REACH OF CHILDREN. (00240a) D.O.T. 4 brake fluid will damage painted and body panel surfaces it comes in contact with. Always use caution and protect surfaces from spills whenever brake work is performed. Failure to comply can result in cosmetic damage. (00239b) NOTE Immediately wipe up any brake fluid spillage with a clean, dry, soft cloth. Follow up by thoroughly wiping affected area with a clean, damp, soft cloth (small spills) or washing with a large quantity of soapy water (large spills)

Incoming search terms:

HARLEY DAVIDSON SOFTAIL FRONT SPOILER KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 09-03-2011

download
This instruction sheet references Service Manual information. A Service Manual for your model motorcycle is required for this installation and is available from a Harley-Davidson Dealer. Kit Contents See Figure 2 and Table 1. INSTALLATION 1. Position the vehicle on a motorcycle lift table. To prevent accidental vehicle start-up, which could cause death or serious injury, remove maxi-fuse before proceeding. (00251a) 2. Refer to the Service Manual and follow the instructions given to remove the Maxi® Fuse. 3. Raise the vehicle on the lift table to allow access to the lower front portion of the frame. 2008+ 2007 7 8 11 3 3 4 4 12 5 5 1 1 9 2 2 10 6 6 9 9 11 13 is02652c 8. 1. Two-pin voltage regulator connector (2007 only) Voltage regulator 2. 9. Voltage regulator attaching screws (2) Cable strap (2 for 2007, 1 for 2008 and later) 10. 3. Lower voltage regulator cover (2007 only) Voltage regulator bracket 4. 11. Bracket screw to engine crankcase (2) Oxygen sensor connector 12. 5. Crank position sensor connector (2007 only) Voltage regulator caddy 6. 13. Voltage regulator caddy cover Horn connectors (some 2008 and later models) 7. Four-pin voltage regulator connector (2007 only) Figure 1. Original Equipment Voltage Regulator  NOTE For 2007 models: The ground wire on the voltage regulator must be re-attached at the original location when re-installing the voltage regulator to ensure adequate ground. 4. For ALL models: See Figure 1. Remove and discard the voltage regulator caddy cover (6) from the regulator bracket (3) and caddy (5). For 2007 models: In addition, remove the lower voltage regulator cover (10). 5. Remove and retain the hex socket head screw (4) at the top left of the bracket For 2007 models: In addition, disconnect the ground wire. Free the cable straps (9) from the regulator bracket, beneath the regulator. 6. Remove the two hex socket head screws with washers (2) retaining the voltage regulator to the bracket. Remove and save the regulator, but discard the screws. 7. Remove and retain the screw (4) at the top right of the regulator bracket. Remove the bracket from the engine. 8. For 2008 and later models: Free the strap (9) that ties the jiffy stand wiring to the voltage regulator bracket. Unfasten the three-way jiffy stand sensor connector and the two-way crank position sensor connector [79] (12) from the T-studs on the back of the regulator bracket (3). Discard the bracket. Disconnect both plugs from the back of the voltage regulator (1). For 2007 models: Unfasten the four-way (7) and two-way (8) voltage regulator connectors from the T-studs on the back of the regulator bracket (3), and discard the bracket. Disconnect the voltage regulator (1) at both connectors. 9. For 2008 and later models: Unclip the two-way O 2 (oxygen) sensor electrical connector [138] (11) from the voltage regulator caddy (5). For 2007 models: Unfasten the two-way crank position sensor connector [79] (12) from the voltage regulator caddy (5). Remove the caddy from the vehicle frame. a. For 2007 models: Unclamp the bottom of the caddy from the engine mount spacers. b. For ALL models: Unhook the top clips from around the tabs on the front of the engine casting. Remove the original equipment (O.E.) caddy from the vehicle frame, and discard it.

Incoming search terms: