PREMIUM STEREO HELMET HEADSET KIT INSTALLATION MANUAL

0

Filed Under (Tips and Review) by admin on 14-02-2011

download
HEADSET INSTALLATION NOTE Carefully follow the installation procedures given in this instruction sheet. Harley-Davidson® makes no warranties, expressed or implied, to cover helmets damaged by improper installation of this headset. If the procedures are not within your capabilities, or if you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Headset Connector and Microphone Installation NOTE Two different helmet clamp styles are provided to fit different helmet shell designs. 1. See Figure 1. Position the headset connector housing (1) to the outer left side of the helmet shell (5), with the boom (2) forward. Position the selected clamp (3) to the inner left-side helmet edge, between the liner (6) and shell. 6 4 2 1 3 5 is05937 1. Headset connector housing 2. Boom 3. Clamp 4. Hex socket head screw (2) 5. Helmet shell 6. Helmet liner Figure 1. Clamp Placement on Helmet 2. Assemble the headset connector housing to the clamp with the two screws (4), but do not fully tighten at this time. 3. Put the helmet on. Adjust the boom and the headset connector housing position as necessary to place the microphone and wind sock in front of the mouth. Remove the helmet. Use the hex key (10) to tighten the clamp screws to hold the headset securely to the helmet. Speaker Installation NOTE Ambient temperature should be at least 60 °F (16 °C) for proper adhesion of the speakers to the helmet. 1. See Figure 7. The speakers must be mounted to a hard surface on the inside of the helmet using the supplied hook and loop fasteners (7). • If the helmet HAS removable ear pads , remove the ear pads from inside the helmet. • If the helmet DOES NOT HAVE removable ear pads , it may be necessary to cut out a small piece of the fabric liner on each side of the helmet to get to the hard inner surface of the helmet shell. 2. Clean the speaker mounting areas inside the helmet with a mixture of 50-70% isopropyl alcohol and 30-50% distilled water. Allow to dry thoroughly. 3. Remove the backing from one side of the hook and loop fastener. Press the assembled adhesive-backed fastener onto a hard surface within the ear pad recess area

HARLEY DAVIDSON SPORTSTER LOW REAR SUSPENSION KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 13-02-2011

download
INSTALLATION NOTE Internal shock absorber components are not repairable beyond the Service Parts listed on this instruction sheet. Consult your Harley-Davidson dealer if further service is required. The installation procedures for this kit are the same as the original equipment (OE) installation procedures in the Service Manual. Refer to the appropriate Service Manual for the rear suspension system removal and installation procedures. The OE hardware will be re-used in the kit installation. Installation of any accessory suspension components can affect cornering clearance. This could distract the rider, causing loss of control and death or serious injury. (00431b) SHOCK PRELOAD (SPRING) ADJUSTMENT Refer to the appropriate Service Manual for spring adjustment. Spanner wrench (94700-52L) is required for spring adjustment. SERVICE PARTS 1 is04854 Figure 1. Service Parts: Sportster Low Rear Suspension Kit Table 1. Service Parts: Sportster Low Rear Suspension Kit Part Number Description (Quantity) Item 54734-04 Rear shock (2)

Incoming search terms:

HARLEY DAVIDSON CLEAR/SMOKED BULLET STYLE OR VRSC TURN SIGNAL LENS KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 12-02-2011

download
Installation NOTE A Service Manual for your motorcycle is available from your Harley-Davidson Dealer. 1. See Figure 1. Locate the removal notch on the turn signal lens and carefully pry from housing. Discard lens. Repeat for remaining lenses. 2. Remove bulbs from turn signal assemblies. 3. Obtain new amber bulbs from kit. Install the bulbs marked 1157A (Dual Filament) to the front turn signal assemblies. Install the bulbs marked 1156 (Single Filament) to the rear turn signal assemblies. NOTE See Figure 1. VRSC (V-Rod) Models have unique rear turn signal lenses. The rear lens is identified with a dimple mark in the center of lens. The front has no dimple. 4. Obtain new lens from kit and install by snapping into place. Check turn signals for proper operation. ® Figure 1. “Bullet” and VRSC Turn Signal Lenses Kit Numbers 69303-02, 69304-02, 69309-02 and 69315-02 Service Parts Clear/Smoked “Bullet” and VRSC Lens Kits Date 5/02 Part No. 69303-02 and Others Item Description Part Number Kit Number 69303-02 1 Clear lens, bullet, front and rear (4) 69324-02 Kit Number 69304-02 2 Smoked lens, bullet, front and rear (4) 69325-02 3 Bulb, amber (front) 69331-02 4 Bulb, amber (rear) 69330-02 Item Description Part Number Kit Number 69309-02 1 Clear lens, VRSC, front (2) 69324-02 5 Clear lens, VRSC, rear (2) 69322-02 Kit Number 69315-02 2 Smoked lens, VRSC, front (2) 69325-02 6 Smoked lens, VRSC, rear (2) 69323-02 3 Bulb, amber (front) 69331-02 4 Bulb, amber (rear

Incoming search terms:

HARLEY DAVIDSON DIAMONDBACK "LE" CHROME SERIES CLUTCH CABLE KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 11-02-2011

download
CLUTCH CABLE REMOVAL To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative (-) cable first) before proceeding. (00307a) Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 1. Disconnect the battery or main fuse following the instructions in the appropriate Service manual. 2. When performing cable disassembly procedures, make careful notes as to the existing cable routing and existing cable strap locations. New straps can be installed in the same locations. 3. Remove the clutch cable following the instructions in the appropriate Service Manual. 4. If installing different handlebars, install them now (refer to the appropriate handlebar instruction sheet) and measure the change in distance that will be required from the end of the cable housing to the clutch lever. Install proper length clutch cables. Incorrect cable length can adversely affect motorcycle operation, which could cause loss of control resulting in death or serious injury. (00448b) 5. Compare the additional required length to the cable provided in your kit. If the cable is more than two inches (50.8 mm) longer or more than one inch (25.4 mm) shorter than the above measured distance, see a Harley-Davidson dealer for the correct cable length. CLUTCH CABLE INSTALLATION Sportster and Softail Models Do not over-tighten clutch cable threaded end fitting. Use recommended torque values. Damage to threaded fitting can lead to loss of transmission fluid, which could result in loss of control and death or serious injury. (00449c) -J04568
NOTE Damage to the clutch cable threaded end fitting due to improper handling/installation is not covered under the Harley-Davidson Motor Company Warranty. 1. See Figure 11. Apply a light coat of clean engine oil on the new O-ring (2) before installing the O-ring onto the threaded portion of the clutch cable end. 2. Install the clutch cable following the instructions in the appropriate Service Manual EXCEPT: Tighten clutch cable fitting to clutch release cover to 36-60 in-lbs (4-7 Nm) . Replace anchor pin with anchor pin supplied in this kit, see Figure 11, item (1 or 7). 3. After installation, follow the instructions in the “Final Assembly” and “Clutch Cable Adjustment” sections in this instruction sheet. FLTR Models with Fairing Lowers 1. See Figure 1. Carefully twist the clutch cable around the coiled opening in the clutch cable guide (2) with the eyelet toward the left handlebar. 2. Route the clutch cable assembly down from the clutch cable clamp while crossing to the right side of the vehicle. Run the cable between the inboard side of the right frame downtube and the outboard side of the voltage regulator. 3. The clutch cable clamp, mounted on the engine guard, has two fingers, an upper and a lower. Feed the cable assembly under one finger and over the other. 4. Finish the installation of the clutch cable following the instructions in the appropriate Service Manual EXCEPT: Tighten clutch cable fitting to clutch release cover to 36-60 in-lbs (4-7 Nm) . Replace anchor pin with anchor pin supplied in this kit, see Figure 11, item (1 or 7). NOTE See Figure 2. Adjust the clutch cable clamp to 2.25 ± 0.25 in. (57.15 ± 6.35 mm) as measured from the inside lower left fairing mount to the clutch cable clamp. 5. After installation, follow the instructions in the “Final Assembly” and “Clutch Cable Adjustment” sections in this instruction sheet.

Incoming search terms:

HARLEY DAVIDSON SOFTAIL DIAMOND BACK SEAT installation instructions

0

Filed Under (Harley Davidson) by admin on 11-02-2011

download
Installation NOTE When this seat and tail section are installed, the passenger foot pegs or foot boards and the passenger grab strap must be removed. NOTE: A Service Manual for your model motorcycle is available at your Harley-Davidson Dealer. 1. Refer to applicable Service Manual and remove original seat, foot pegs or foot boards and grab strap. 2. Refer to Tail Section Instruction Sheet for instructions describing how to attach the tail section to the seat and installing the seat on the motorcycle

HARLEY DAVIDSON SADDLEBAG GUARD RAIL KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 11-02-2011

download
Installation NOTE A Service Manual for your vehicle is available from your Harley-Davidson Dealer. 1. Remove saddlebags from motorcycle according to Service Manual instructions. 2. Remove left and right side covers (located just ahead of saddlebags) by removing Phillips head screw from bottom of side cover. Save hardware and side covers for later reassembly. 3. Remove upper and lower bolts securing left and right forward saddlebag guards to frame. Remove Phillips head screws securing saddlebag guards to muffler supports. Discard saddlebag guards, but save hardware. 4. See Figure 1. Install new left and right forward saddlebag guards (1) with upper bolts (2), lower bolts (3) and Phillips head screw (4) saved from Step 3. 5. Insert one rear guard rail mount (6) onto rounded, tubular end of one of the saddlebag side guard rails (5). 6. Insert a hex cap screw (8) through one of the front guard rail mounts (7) as shown. 7. Line up saddlebag side guard rail (5) with attached rear guard rail mount (6) from Step 5 with lower hole in forward saddlebag guard rail (1). Insert hex cap screw (8) from front guard rail mount (7) through hole in forward guard rail (1) and into side guard rail assembly. Tighten finger tight. 8. See Figure 2. Install a side guard rail (2) in lower position on rear fender support (3) with pan head screw (1). Tighten finger tight. 9. Repeat Steps 5 through 8 in upper position. 10. Repeat Steps 5 through 9 for opposite side of vehicle. NOTE Each of the four guard rail clamps vary slightly. Two fit together for the right side of the motorcycle and two fit together for the left side. The inner right and left clamps have two holes drilled through them. 11. See Figure 2. Locate four guard rail clamps (4). Match up two left side and two right side guard rail clamps. Install one piece of cushion tape to the lower inner surface of right and left inner clamps. Peel off paper from outer surface of tape. Do not apply tape to the outside clamps. NOTE Be sure that you correctly position the inner clamps on the side guard rails, as directed in Step 12, before tape on inner clamp contacts side guard rails. Tape is very sticky and will be difficult or impossible to remove once it has made contact with side guard rail surface. 12. See Figure 2. Position clamps (4) in desired position on side guard rails (2). Install clamps (4) on left and right side of vehicle side guard rails using four Torx screws (5). Torx screw heads should face inward toward motorcycle. Tighten each screw a little at a time until secure. 13. Tighten hex cap screws and pan head screws installed in Steps 7 and 8.

Incoming search terms:

HARLEY DAVIDSON LOCKING FUEL FILLER CAP KIT REMOVAL AND INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 11-02-2011

download
INSTALLATION 1. Prior to installing the gas cap on the vehicle, insert the key into the lock. Firmly grasp the chrome top of the fuel cap and turn the key until it stops. On right hand threaded fuel caps, turn the key counter-clockwise until it stops. On left hand threaded fuel caps, turn the key clockwise until it stops. This assures an unlocked position for the gas cap. Allow the key to return to the neutral position. 2. Remove the key and install the fuel cap on the vehicle. is00770 Figure 1. Right Hand Threaded Fuel Cap Installation NOTE When installing the fuel cap, rotate the cap one full turn past the audible click. This automatically positions gas cap to lock position. A properly locked/installed gas cap will rotate freely in both directions. Failure to do so will give an incorrect assumption that the fuel cap does not work properly. REMOVAL On right hand threaded fuel caps, insert key, and while holding the gas cap in place with hand, turn key counterclockwise until it stops, return key to original position. Gas cap must rotate 270 degrees counter-clockwise before mechanism engages to allow gas cap removal. Continue to rotate counterclockwise to fully remove gas cap. On left hand threaded fuel caps, insert key and while holding the gas cap in place with hand, turn key clockwise until it stops, return key to original position. Gas cap must rotate 270 degrees clockwise before mechanism engages to allow gas cap removal. Continue to rotate clockwise to fully remove gas cap. REPLACEMENT KEYS Record the 4 digit key number stamped on the back of the key opposite the Harley-Davidson logo, in the area provided below. If a replacement key is needed, see your Harley-Davidson Dealer with the 4 digit number to order a replacement

Incoming search terms:

HARLEY DAVIDSON SOFTAIL SADDLEBAG KITS INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 10-02-2011

download
INSTALLATION Do not exceed saddlebag weight capacity. Put equal weight in each bag. Too much weight in saddlebags can cause loss of control, which could result in death or serious injury. (00383a) NOTES Maximum saddlebag weight capacity is 7 lbs (3.18 kg) for each bag. Proper installation of these kits requires that tasks be completed for one side of the motorcycle first before continuing to the opposite side. 2000-2002 Models with Wide Tire Kit 1. See Figure 1. Remove and discard stock screws (1) and washers (2) from fender support. Button head screws from wide tire kit must be installed with button heads on inside of fender. Fastener contact with tire can lead to premature tire failure, which could result in death or serious injury. (00417b) 2. See Table 3. Determine appropriate screw from wide tire kit. 3. See Figure 2. Install saddlebag using screw (from wide tire kit) (1), washer (2) and nut (3). The screws are installed from inside to outside of fender. NOTE If you do not have the appropriate screw from the wide tire kit, it can be purchased from a Harley-Davidson dealer. Table 3. Wide Tire Kit Screws (3/8-16) Wide Tire Kit 44490-00, Hardware Kit 43763-00 Wide Tire Kit 44490-00, Hardware Kit 43761-00 Part Number and Length X X 4030 – 2-1/2 inch X X 4225 – 3-1/2 inch X X 4224 – 1-1/2 inch X X 4044 – 1-1/4 inch X 4215 – 2 inch X 3912 – 2-3/4 inch X X 4228 – 2-1/4 inch X X 4229 – 3-1/4 inch Failure to tighten saddlebag mounting bolts to specified torque could result in damage to saddlebags. (00406c) 4. Tighten all saddlebag hardware to 22 ft-lbs (30 Nm). NOTE Check that front screws have at least one thread exposed beyond the nut after proper torque has been applied. 5. Install reflectors on saddlebag. Refer to Install Reflectors subtopic.

Incoming search terms:

HARLEY DAVIDSON CLEAR/ SMOKED DOMED OR FLAT TURN SIGNAL LENS KITS INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 09-02-2011

download
CLEAR/SMOKED DOMED OR FLAT TURN SIGNAL LENS KITS Installation NOTE A Service Manual for your motorcycle is available from your Harley-Davidson Dealer. 1. See Figure 1. Remove existing turn signal lenses and discard. Retain lens mounting screws for installation. 2. Remove bulbs from turn signal assemblies. 3. Obtain new amber bulbs from kit. Install bulbs marked 1157A (Dual Filament) to the front turn signal assem- blies. Install bulbs marked 1156 (Single Filament) to the rear turn signal assemblies. 4. Refer to Figure 1. Using screws saved during removal, install the new turn signal lenses to front and rear turn signal assemblies. 5. Check turn signals for proper operation

HARLEY DAVIDSON FLAME SHIFTER PEG/ HEEL REST PAD KITS INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 06-02-2011

download
INSTALLATION NOTE A Service Manual for your motorcycle is available at your Harley-Davidson Dealer. To enhance the flame pattern, orient the pegs as shown in Figure 1. 1. If replacing shifter peg, remove and discard existing shifter peg. If needed, apply heat with a heat gun to shift lever threads and threads on shifter peg to aid peg removal. If installing heel rest pads, proceed to Step 3. 2. See Figure 1. Using screw (6), attach shifter peg casting (1, 2) to shift lever. Tighten screw to 16.3-19 Nm (12-14 ft-lbs). NOTE Screw (6) has a lock patch to prevent loosening. 3. To install heel rest pads, perform Step 2 to attach the heel rest to the right or left heel rest lever