HARLEY DAVIDSON FAIRING MOUNT MIRRORS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 20-02-2011

download
INSTALLATION Removing Outer Fairing 1. Standing at the front of the vehicle, use a T-27 TORX® drive head to remove the three outer fairing screws (with flat washers) just below the windshield. 2. Moving to the inner fairing side, use a T-27 TORX drive head to remove the two fairing screws just above the wind deflectors on the left and right side. 3. Turn the handlebar to the right and remove the outer fairing screw (reach in below the fairing cap). Turn the handlebar to the left and remove the fairing screw on the opposite side. 4. Tilting the outer fairing toward the front, squeeze the two external tabs to remove the wire connector at the back of the headlamp assembly. 5. Lift the fairing (with headlamp assembly) off the motor- cycle. NOTE Since the outer fairing screws hold the windshield in place, the windshield may fall to the floor if not removed. 6. Remove the Windshield. Installing Mirrors 1. See Figure 1. Place template on inside of fairing as shown to locate mounting holes for mirror. 2. Begin by drilling a 1/8 inch pilot hole at each location marked on the template. For the center hole (2) where the 3/8 inch threaded stud passes through the fairing use a 13/32 inch diameter twist drill to drill the hole to its final size. For the alignment hole (1), use a 7/32 inch diameter twist drill to drill the hole to the final size. 2 1 is 02115 1.7/32 inch hole location 2.13/32 inch hole location Figure 1. Positioning Template 1 is06315 1. Auxiliary mirror Figure 2. Orientation of Auxiliary Mirror NOTE The flange nut is a self locking nut and must not be tightened more than 30 in-lbs (3.4 Nm). 3. See Figure 3. Place mirror (2) in position and install backing plate (4) with the raised post (B) (with the L and R marking) toward the nut surface. Install the flange nut (6) and tighten nut to 20-30 in-lbs (2.3-3.4 Nm). 4. See Figure 2. Position the mirror so the round auxiliary mirror is in the upper inside corner position. 5. Repeat for right side

HARLEY DAVIDSON FAIRING BRA INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 05-02-2011

download
This kit is designed for installation on 1996 and later FLHT, FLHTC, FLHTCU AND FLHTCU/I Model Motorcycles. Installation 1. Align each of the sewn-in pockets on the fairing bra with each of the outer edges of the fairing at handlebar level. 2. See Figure 1. Standing in front of the vehicle, remove the three T27 Torx screws (1) with washers securing the windshield along the front of the fairing. NOTE In the following Step, the Chrome Windshield Strip (purchased separately) , will serve as a mounting bracket for the fairing bra 3. Obtain the Chrome Windshield Strip (P/N 59213-96) and screws supplied with strip. While aligning holes in the chrome strip over the bra, install the new screws with washers through the strip and bra, then tighten securely into the windshield. 4. The six straps (three on each side near the bottom) will be captured between the inner and outer fairing. Refer to Figure 1. Remove the four screws (2) from the inner fairing. NOTE: The bottom two screws are below the fairing cap. Save screws for installation. Separate the inner and outer fairings just enough to install the straps into the fairing. Adjust the straps, then reinstall the screws and tighten securely. 5. Remove the Phillips screw located at the bottom of the headlamp trim ring. Save screw for installation 6. See Figure 2. Orient the elastic portion of the bra around the headlamp, however in front of, the retaining ring as shown. 7. Install the bottom elastic strap below the fairing seal under the headlamp. 8. Install the headlamp trim ring using the Phillips screw removed in Step 5.