CYCLE SOUNDS T-TAP POWER HARNESS INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 21-04-2012

download
This t-tap plug is designed to work with Cycle Sounds audio systems. However it can be used to wire many add on 12 volt accessories to you Harley Davidson motorcycle. This plug is rated for 6-8 amps of power and should not be used for adding any product that is rated for more than the t-tap plug is rated for. Take the time to check the products power rating for which you want to install to make sure it is compatible with the t-taps amperage rating. Failure to do so couldlead to electrical failures, which could result in serious injuries or even death. it is possible to overload your motorcycles charging system by adding too many electrical accessories. U se amp meter to verify all power connections. Also check product power ratings for anything you are trying to install. Exceeding the maximum amperage can lead to electrical failures, which could result in serious injuries or even death. INSTRUCTIONS: Step 1: remove seat on bike and locate the wire harness under the seat that matches the plugs on the t-tap harness (2120-0026.) Location may vary between bike models. Step 2: unplug bike harness and snap each end of t-tap harness in correct plug opening. When finished connect power wires to the male plug.(all Cycle Sounds audio systems come pre wired with correct wire colors and terminals). When using this t-tap for any other 12 volt accessory, make sure the red and black wires are snapped into their proper pin connectors. Kit does not come with power terminals for the accessories device. See your local bike dealer for purchase of terminals

Harley-Davidson Auxiliary LED Brake Light Installation Manual

0

Filed Under (Harley Davidson) by admin on 28-03-2012

download
If you are mounting the lighthead on a Harley-Davidson® motorcycle box, use the existing wire hole. Drill your mounting holes so the wire hole (located very close to the mounting hole in the lighthead) will line up with the wires, but not interfere with the mounting holes. Since the lighthead can mount to any vehicle, this manual will cover mounting to a generic location. 1. Mark the location of the 2 mounting holes onto the mounting surface using the dimensions shown above, or remove the lens and use it as a template. Always check behind the mounting surface to be sure you will not interfere with any other vehicle components. 2. Drill the 2 mounting holes using a drill sized for a #6 sheet metal screw, then drill the 9/32″ wire access hole 5/16″ away from the mounting hole as shown. 3. Feed the wires through the wire hole then secure the brake light to the mounting surface with the supplied mounting hardware. 4. Wire the lighthead into your existing brake light wiring, matching the lighthead wire colors to the vehicle wire colors (see “Wiring”). WARNING! All customer supplied wires that connect to the positive terminal of the battery must be sized to supply at least 125% of the maximum operating current and FUSED at the battery to carry that load. DO NOT USE CIRCUIT BREAKERS WITH THIS PRODUCT!

Harley Davidson Power Pod Switch Housing Throttle Bracket Installation Instructions

0

Filed Under (Harley Davidson) by admin on 19-03-2012

download
Attach the “Y” bracket to the Power Pod by using the two Power Pod socket head screws that come in your parts kit. (This bracket may already be attached from the factory. ) 2) Remove the two screws on the Right Hand switch housing on your Harley Davidson motorcycle and reinstall them through the two “Y” bracket open holes and back into the switch housing holes. Tighten snugly. In this mounting position, the heads of the two socket head screws holding the “Y” bracket to the Power Pod should be touching the handlebar; this is necessary as it grounds the unit for proper operation. If the unit is not grounded properly, it will not operate. 3) Run the Power Pod’s 60″ power cord to your battery. Make sure as you hide the cord on the way to the battery, that your handlebars turn freely and that the cord does not come in contact with hot engine parts that may melt the wire over time. 4) At some point, before reaching the battery, attach (using the two butt connectors) the in-line fuse holder. TIP: Keeping the in-line fuse holder in an easy to access place (like under a side panel etc) rather than under the seat, may help you service the fuse easier in case of a blown fuse. In most cases, it’s easier to pull a side panel off than it is to remove a seat! 5) Attach the Power Pod lead wire (with in-line fuse now already attached) directly to the battery for power at anytime without using the key. The hot lead can also be run to the fuse box which will require using the ignition switch to “Accessory” or “ON” in some cases. TIP : Always use the in-line fuse for safety. 6) Insert the 20 amp fuse into the in-line fuse holder. Strap down with zip-ties any loose wires and you’re done!

Incoming search terms:

HARLEY DAVIDSON MOTORCYCLE SIREN INSTALLATION AND OPERATING INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 15-03-2012

download
Before attempting installation, insure that the parts shown in the Kit Contents List (paragraph D.) have been included. To install the chassis, proceed as follows: 1. Insert two shock mount grommets into the large holes in each (2) mounting bracket (see figure 1). 2. Secure a mounting bracket to the chassis with two (each) #10 thread forming hex. head screws and #10 flat washers as shown in figure 1. Secure the other mounting bracket with like hardware. 3. Select a mounting location on the radio mounting platform which allows the siren cable to reach the motorcycle wiring harness, maintains the structural integrity of the motorcycle, and will not interfere with the safe operation of the motorcycle or the siren. 4. Using the supplied mounting template, scribe four drill position marks at the selected mounting location. CAUTION To avoid damage when drilling, ensure that both sides of mounting surface are clear of any parts or wires

Harley Davidson Motorcycle 1982-2009 Standard Signal Mirror Kit INSTALLATION

0

Filed Under (Harley Davidson) by admin on 23-02-2012

download
Remove the 5/ 16 ” bolt from the mounting stem on the Signal® mirror. While seated on the motorcycle, position the Signal® mirror on the handle bar. Secure the Signal® mirror to the handle bar using the 5/ 16 ” bolt. NOTE: Use of oil is suggested if bolts do not thread easily into stem base. Make sure the bolt is tight! Guide the Signal® mirror wire harness into the cowling by going along side the existing factory wire harness. 4 Remove any slack in the wire harness. Secure the wire harness to the handle bar using a supplied tie wrap. 5 6 Adjust the position of the Signal® mirror and tighten the ball retention screws. Start on either the left or right side mirror. These instructions start with the right side mirror. Remove the factory mirror. NOTE: For motorcycles with OEM forward facing indicators, please use the instructions on the last page in lieu of step 2.

HARLEY-DAVIDSON MOTORCYCLE WASH KIT MANUAL

0

Filed Under (Harley Davidson) by admin on 02-03-2011

download
THE WASHING PROCESS Allow the motorcycle to cool to the touch. Cool water can damage a hot motorcycle. 1. Pre-Wash: a. Verify the motorcycle is cool to the touch. b. Rinse the motorcycle from the bottom up. c. Verify you have the proper cleaning supplies. d. Spray on Bug Remover and let the product activate while proceeding to the next step. 2. Wheels and Tires: a. Rinse wheel and tire surfaces. b. Apply Wheel and Tire Cleaner. c. Wait one minute after spraying product. d. Clean wheel with a Soft Detailing Pad or Wheel and Spoke Brush. e. Rinse well. 3. The Wash: a. Have two buckets; one for the cleaner and one for rinsing. b. Pour Sunwash into the Harley-Davidson Cleaning Bucket and fill with water. c. Fill the rinsing bucket with clean, plain water. d. Soak the Wash Mitt in the Sunwash solution. e. Wash all surfaces from the top working down. f. Rinse from the bottom up first. g. End with top down rinse. 4. Drying the Motorcycle: a. Use the Soft Drying Towel to dry surfaces of the motorcycle. b. Dampen the towel in clean water. c. Wring out the towel as often as needed and continue until the surface is completely dry. 5. The Polish and Seal : (not applicable for denim paint finishes) Polishing and sealing isn’t just about good looks . A well cared-for motorcycle repels dust, dirt, bugs and dirty water. a. Use Harley Glaze polish and sealant and follow the instructions on the bottle. b. Use Softcloth disposable towels for application. c. A Softcloth or Microfiber detailing cloth is an absolute must for finish buffing. d. In between Harley Glaze applications, use Harley Spray Cleaner and Polish and Harley Gloss to maintain shine and protection of painted and chrome fin- ishes.

Incoming search terms:

Harley Davidson engine modification

0

Filed Under (Harley Davidson) by admin on 02-11-2010

download
Looking for high performance engine specifications for your Harley- Davidson motorcycle? Need to know what high performance equipment provides the best performance at the lowest costs for your H-D. Here you can look at performance modifications with the dyno runs of many different engine combinations, so you can pick your own equipment, horsepower rating and dollars to spend. An incremental approach to engine development has provided some good results on many engines. Find out what combination of carburetor, camshaft, exhaust systems, ignition systems, head work, pistons and the other high performance components work well. There are tests of some equipment that did not work well. Know what works and what does not. Compare the results of your current bike to those seen here. Are you getting the performance you paid for? If you have had success in your engine development program, send a picture of the bike and your performance results (dyno sheets or time slips) to the V -Twin Café for publication. The V -Twin Café is always looking for good articles on motorcycle performance work. If you write performance oriented articles, contact us. Twin Cam 88 and 95 cubic inches Twin Cam Engines from Harley-Davidson have a good design and some nice upgrades available from the local Dealer including a 95 cubic inch big bore kit. What can you expect from this engine? Here are some engine configurations that have been tested. 45 to 50 HP Stock Evolution Engines are the starting point for all the modifications. The only way to validate what the performance gain was for any change is to have dyno runs before and after. These are the before runs of several bikes. 55 to 65 HP Up to $750 Stage One Evolution Harley-Davidson engines involve no internal changes made to the engine. All modifications are made by changing or modifications to external components on the engine. These components include air cleaners, carburetors, exhaust systems and ignition systems. No special tools or training is required to perform stage one modifications.

Incoming search terms:

Harley-Davidson Motorcycle Reverse Gear Installation Instructions

0

Filed Under (Harley Davidson) by admin on 31-10-2010

download
2.1 Obtain a small tube of Loctite® #262 (red) for use later. 2.2 Drain the transmission oil. 2.3 Remove the clutch adjustment cover (left side). 2.4 Remove rear exhaust header pipe (cross over exhaust pipe). 2.5 Remove the muffler support bracket. 2.6 Remove the clutch release cover (right side). 2.7 Remove clutch push rod and oil slinger. To be disassembled and modified later. 2.8 Remove the two nuts from the main (rear) and counter (front) transmission shafts. 2.9 Remove the transmission bearing housing (puller available from Champion Sidecars). To be replaced with new reverse gear transmission bearing housing (Trap Door). 2.10 Cover the exposed gears in the transmission with a cloth in preparation to cut the shifter fork shaft. 3 Install New Main and Countershaft Gears NOTE: Gears and Tapered Split Rings are factory matched sets. Do not mix!. 3.1 Locate the shifter fork rod, mark fork rod flush at transmission case and pull out 1/4″. Figure 1 Figure 2. Exposed Shoulders Mark shifter fork rod flush with case Remove Spacers Vehicle Transmission Counter Shaft Main Shaft Front of Motorcycle Figure 1
Reverse Gear Installation Instructions For EVO / 5 Speed and Twin Cam Harley-Davidson® Motorcycle Page 3 of 6 Revision 7 © 2007 Champion Motorcycle Accessories International, Inc. dba Champion Sidecars 11841 Monarch Street Garden Grove, CA 92841 (800) 875-0949 (714) 847-0949 www.championsidecars.com www.championtrikes.com Figure 6 CAUTION: Do not pull the shifter fork rod out of the transmission more than 1/4″. If you pull the shifter fork rod out too far, it will be difficult to realign it with the internal shifter fork. 3.2 Cut the shaft at the mark and push it back in. The shaft end MUST NOT stick out of the transmission case. If the shaft is in deeper, fill the hole with silicone to prevent the shaft from moving in and out. NOTE: Shifter fork is made of non-tempered metal and may be cut with a hacksaw or Dremel® cutting tool. 3.3 Important: Remove stock spacers from main and counter shafts. Spray with silicon remover (Brake-Clean) then, using supplied cleaning pad, clean shafts, new counter and main shaft gears and tapered lock rings (inside and outside) Figure 1 3.4 With motorcycle in neutral, pull both the shafts out and simultaneously push the OEM outermost gears in until seated completely to expose the shoulders of both shafts. The countershaft shoulder should be flush with the gear face. For the main shaft the gear would “hang over” the shoulder a small bit. Figure 2 3.5 Apply supplied Champion Super-Lock retaining compound to the inside and outside surfaces of the large gear tapered split ring, to the inside of the new countershaft gear (large gear) and to the transmission countershaft (the forward most shaft). 3.6 Install new countershaft gear to the transmission countershaft. Insert tapered split ring (tapered end first) into the countershaft gear. Install ring seat tool and spring to counter shaft and new countershaft gear. Torque ring seat tool to 40 ft-lb’s. Figures 3 and 4

Incoming search terms:

Edelbrock Nitrous Systems Digital RPM Window Switch USER MANUAL

0

Filed Under (Harley Davidson) by admin on 31-10-2010

download
Programming the RPM The engine application and rpm activation points are easily selected through push buttons on the LED panel. This Switch can be programmed for a variety of engine and ignitions as shown below. 1-Cylinder This program is used for individual coil per cylinder systems (such as GM LS-1 engines, or ’99-Up Mustangs) 2-Cylinder This is for ignitions with coil packs that fire two cylinders at the same time (waste spark systems) 2-Cyl. Odd Use on coil pack ignitions that are on odd-fire engines such as a Viper V-10 or Harley-Davidson motorcycle. 4-Cylinder Typical 4-cylinder engines with a distributor. 6-Cylinder Typical 6-cylinder engines with a distributor. 6-Cyl. Odd Typical 6-cylinder odd-fire engines with a distributor. 8-Cylinder Typical 8-cylinder engines with a distributor. 1.2 Push Button LED Panel The rpm activation points and cylinder select are programmed through the push buttons on the LED panel (Figure 1) . Press the Mode button, and notice that the indicator point above the On RPM lights. When that point is on, you can scroll the rpm value up or down with the arrows on the left of the panel. Once your On rpm is set, push the Mode button until the Off RPM point lights, then set the off rpm point. Note that if the rpm point is not changed within 2-seconds, the screen returns to the current rpm reading (zero when the engine is not running). After setting the On and Off points, press the Mode button to program the Cylinder Select Valve (default is for 8-cyl.