1999-2003 Harley Davidson TC88 Micro Tach TM Tachometer Installation Manual

0

Filed Under (Harley Davidson) by admin on 10-03-2012

download
Installation of the Speedway Instruments microTach+TM tachometer requires some basic mechanical skills, including removing decorative covers, cutting protective tubing around wires, and using suitcase splice connectors to splice existing wiring harness. These actions may void your warranty, and if done incorrectly may cause damage to your motorcycle. Only you know your capabilities, if you do not feel capable of making modification please have a qualified motorcycle technician install it. Speedway Instruments, LLC is not responsible for damage to your motorcycle due to improper installation. The microTach+ TM tachometer designed for 1999-2003 TC88 Harley Davidson motorcycles is designed to operate when connected to a dedicated Tachometer signal from the Electronic Ignition Controller. It is not intended to run off signals going to the ignition coil unless utilizing a Speedway Instruments Tach Adapter. WARNING: Damage may occur to the microTach+ TM tachometer or your motorcycle if micro Tach+ TM tachometer is connected directly to coil signals, you must use a Speedway Instruments tach Adapter (sold seperately) ! ! 1. Turn ignition off and disconnect Battery. 2. Determine a mounting position. Each motorcycle is unique and the microTach+TM tachometer is small enough to be placed in many different locations to provide an attractive appearance and vital engine status. Possible locations are: a. Front Brake Reservoir

HARLEY DAVIDSON SPLIT VISION MIRROR KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 18-02-2011

download
These kits are designed to fit all 1982 and later Harley- Davidson motorcycles. Kit Contents See Figure 1 and Table 1. INSTALLATION 1. Remove and discard the existing mirror. Discard any lockwashers and acorn nuts used to mount the original mirror. 2. For motorcycles with turn signals mounted to the underside of the hand lever housings except 2004 and later XL models: See Figure 1. Secure the left side mirror using only the flat washer (3) and the acorn nut (5) from the kit. 3. Secure the right side mirror with the flat washer (3) and acorn nut (5) from the kit and the turn signal retainer only. Do not use washer (4) on either side. For 2004 and later XL models use only the lockwasher (4), and acorn nut (5) on each side. 4. For motorcycles with turn signals mounted away from the hand lever housings: Insert the mirror studs into the holes in the hand lever housings, and secure the mirrors with the flat washers (3), lockwashers (4) and acorn nuts (5) from the kit. 5. Adjust the mirrors for proper field of vision and tighten the acorn nut to 12 ft-lbs (16 Nm). Check mirror adjustment and reposition if necessary

HARLEY DAVIDSON SKULL SHIFTER PEG/ HEEL REST PAD KITS INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 01-02-2011

download
Models Shifter Peg Kit, Part Number 34689-04 is designed for installation on all model Harley-Davidson motorcycles. Heel Rest Pad Kit, Part Number 34699-04 is designed for installation on all models equipped with a Heel Rest Kit, Part Number 50227-01 or 50236-01. INSTALLATION Shifter Peg 1. Remove and discard the original equipment shifter peg. If needed, use a heat gun to apply heat to the shift lever and shifter peg threads to aid in peg removal. 2. See Figure 1. Using the screw (5), attach the peg (1) and tread (3) assembly to the shift lever. Tighten the screw to 12-14 ft-lbs (16.3-19 Nm). Heel Rests NOTE The chrome heel rest covers are side-specific. For best appearance, install so the HARLEY-DAVIDSON text is above the skull, and the MOTORCYCLES text below . 1. See Figure 1. Using the screws (5), attach the left-side heel rest (1) and tread (3) assembly to the left-side heel rest lever. Tighten the screw to 12-14 ft-lbs (16.3-19 Nm). 2. Repeat for the right-side heel rest (2) and tread assembly

HARLEY DAVIDSON SECURITY SYSTEM KITS INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 30-01-2011

download
FL Touring models equipped with a TLE/ TLE Ultra Sidecar will require the additional installation of a Bank Angle Switch Kit (88115-03) and is available for separate purchase. See a Harley-Davidson dealer.INSTALLATION 1. Remove the original equipment (OE) Turn Signal Module (TSM) or Body Control Module (BCM) following the instructions in the service manual. 2. Install the Bank Angle Sensor (BAS) on sidecar vehicles. 3. Install the new turn signal/security module (TSSM) (7), Hands Free Security Module (HFSM) (1) or BCM (9, 11) from this kit, following the instructions in the service manual. Configure the Trike or sidecar TSSM, HFSM or BCM to “Side Car Enabled” using Digital Technician. 4. Install the Hands Free Security Module (HFSM) Antenna and antenna mount (6) if necessary, using the service manual instructions. Be sure that all lights and switches operate properly before operating motorcycle. Low visibility of rider can result in death or serious injury. (00316a) ACTUATION 1. See a Harley-Davidson dealer to activate the key fob to the TSSM, HFSM or BCM. NOTE You can activate the TSSM fob by referring to the procedure in the electrical diagnostic manual. TRIKE AND SIDECAR CONFIGURATION (FL TOURING MODELS ONLY) Only Touring Harley-Davidson Motorcycles are suitable for sidecar use. Consult a Harley-Davidson dealer. Use of motorcycles other than Touring models with sidecars could result in death or serious injury. (00040a) NOTES FL Touring Models equipped with TLE/TLE-Ultra Sidecar require the installation of a Bank Angle Sensor (88115-03). Failure to install and configure a Bank Angle Sensor may result in death or serious injury. Sidecar and Trike configuration of the security system requires the use of a Digital Technician. Consult your Harley-Davidson dealer or the sidecar or Trike service manual for complete details. On vehicles equipped with a sidecar, the security system must be reconfigured from the default solo vehicle setting to the sidecar setting

Incoming search terms:

HARELY DAVIDSON BOOM! AUDIO TANK POUCH OPERATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 29-01-2011

download
This kit will work on all Harley-Davidson® motorcycles with a metal fuel tank. Always clean fuel tank before using the Audio Tank Pouch, to prevent trapped dirt from scuffing or scratching paint. Scuffing and fine scratches can be removed using Harley-Davidson® Swirl & Scratch Treatment. •See Figure 1. Flip access flap (3) fully to the front as shown to put media player into the pouch (1). •Remove the cushion from the inside of the pouch. Place the media player face-up on top of the cushion and slide both back into the pouch. Make sure the cushion is under the media player for the best protection. •See Figure 2. Two access holes (2) are available for connecting headphone or speaker connectors (3). •Place the media player and pouch (1) on top of the fuel tank and verify that the magnets are holding the pouch firmly in place. 2 3 1 is06064 1. Audio tank pouch 2. Cushion 3. Access flap Figure 1. Audio Tank Pouch and Cushion 2 2 1 3 is06061 1. Audio tank pouch 2. Access hole (2) 3. Headphone connector Figure 2. Audio Tank Pouch on Fuel Tank

HARLEY DAVIDSON V-ROD Fi2000 Fuel Injection Module Installation Manual

0

Filed Under (Harley Davidson) by admin on 15-11-2010

download
1. Flip up seat, to gain access to radiator reservoir area. 2. Remove Dzus fastener to remove simulated fuel tank cover, over airbox housing. Depending on which model V-Rod is being worked on, the front shrouds covering the upper front frame section may also need to be removed. 3. Place Fi2000 in under-seat area, run fuel injector connector harness up right side frame rail between top right frame rail, and radiator overflow tank, see Figure 1. At the rear of the airbox, route the harness below the airbox, and downward next to the inner radiator hose. Unplug both stock fuel injector connectors, on the front and rear injectors between the engine cylinders, see Figure 2. These are disconnected, by depressing the metal springs that are on the end of each female connector. The stock female connectors are marked “F” and “R”, noting which connector goes to the front and rear injector, be sure to pay attention to this. Now connect the longer male Fi2000 connector to the front female H.D. connector. Plug shorter Fi2000 male connector into the stock rear female H.D. connector. Then plug the longer female Cobra connector onto the front stock H.D. injector. Plug the shorter Fi2000 female connector onto the rear injector. Each injector connector pair should rest underneath each respective injector. 4. It is now time to install the oxygen sensor eliminator modules. This product is designed to eliminate the “check engine” light from coming on when the stock oxygen sensors are disconnected on Harley Davidson Motorcycles utilizing fuel injection. The motorcycle has a full “open loop” fuel injection map written in its ECU and the motorcycle reverts to this default map after the oxygen sensors have been removed or just disconnected. 5. Locate the rear oxygen sensor and follow the harness up to the under-seat area behind the radiator overflow tank. Pull the stock connectors up from below the overflow tank and disconnect, see Figure 1. Plug one of the supplied Oxygen sensor eliminators on to the stock male connector. Tuck the connectors back underneath the bracket behind the radiator overflow tank. 6. Now locate the front oxygen sensor on the front headpipe, and trace the oxygen sensor harness back to the connectors tucked between the left front frame rail and plastic radiator shroud, see Figure 3. Pull these connectors out, and disconnect them. Plug the remaining supplied oxygen sensor eliminator on to the stock male connector. Tuck the connectors back in between the frame rail and plastic shroud

2008 HARLEY-DAVIDSON FXCW Softail Rocker Specifications

0

Filed Under (Harley Davidson) by admin on 03-11-2010

download
Three-phase, 38-amp system ………………………………………. (439W @ 13V, 2000 rpm, 489W max power @ 13V) Starting……………….. 1.2 kW electric with solenoid shift starter motor engagement Lights (as per country regulation): Headlamp ……………….. Quartz Halogen, 55-watt low beam, 60-watt high beam Tail/Stop ghts……………………………………………………………….. Integrated LED Turn Signal Lights ……………………………………………………… 21W self-canceling Instruments …………………. Tank-mounted electronic speedometer with odometer; ………………………………………………… Time-of-day clock; Dual resettable tripmeter Indicator Lamps …………………… High beam, neutral, low oil pressure, turn signals, ………………………………………………………….. engine diagnostics, security system6, ……………………………………………………………………….. 6-speed, low fuel warnings Colour Options7 Vivid Black; Pacific Blue Pearl; Crimson Red Sunglo Model Features Silver powder-coated engine; Custom finned cast aluminium “horseshoe” oil tank with chrome external oil lines; Painted, stretch low profile tank console; Fire-truck inspired bullet headlamp; Bullet style LED turn signals; Adjustable, V-bar riser; Forward-mounted rider footpegs; Stainless steel, pull-back, internally-wired handlebars; Lowest seat height of all Harley-Davidson® motorcycles Warranty Warranty8 ……………………………………………………… 24 months (unlimited mileage) Service Interval9 ………………………………………………. First 1,000 miles (1,600 km), ………………………………………………………. every 5,000 miles (8,000 km) thereafter Dimensions