Harley-Davidson Amp Module – Base Kit Installation Manual

0

Filed Under (Harley Davidson) by admin on 10-03-2012

download
Technique for removal of Ampseal contacts from the connector housing (refer to Photos 5 and 6): Grab the wire to be removed (shown in the next section) with needle nose pliers or hemostats. While rotating the wire back and forth over a half turn (1/4 turn in each direction), gently pull the wire until the contact is removed. Photo 5- Pin Removal, Step 1 Photo 6- Pin Removal, Step 2 End of Removal Technique Installing Kennedy Harnesses part #85910 and 85911 Locate Kennedy harnesses part #85910 and 85911 and 5 pieces of 1/8″ diameter x 2″ shrink-wrap, from kit part number 85615-10. Refer to Figure 1 (Pre-’06) and Figure 1a (2006 and Newer) on the next page, and make the connections between Ampseal connector 28B and Kennedy harness 85910, and harness 28B and Kennedy Harness 85911.

2006 Honda GL1800 AirbagCB Radio Squeal REPAIR PROCEDURE

0

Filed Under (Honda) by admin on 08-04-2011

download
To remedy this problem, a ferrite core harness kit is now available for installation. 2006 GL1800 VIIIA (Airbagmodels) with optional CBRadio. Install a ferrite harness core kit according to the installation instructions that are packaged with the kit. ÒÑÌÛæ • The kit includes both a rider and a passenger harness; it’s necessary to install both harnesses to eliminate the squealing noise. • Passengers must route the headset cord as shown. If routed otherwise, it will be too close to the motorcycle’s antenna, which can create an interference. Subharness installation can be confirmed by removing the left-side fairing pocket, and check- ingtoseeifthe harness is already installed. Ferrite CoreHarness Kit (1 required) P/N: 08E95-MCA-100WA H/C: 8607665 ÒÑÌÛæCallTechLineat (800) 421-1900 to order parts. Due to the limited number of affected units and parts availability, ordering will be controlled until May 31,2007. Normal warranty claim submission require- mentsapply. Submit one claim per VIN. Template: GL19 Flat RateTime: 0.3 hours

Incoming search terms:

SR-C400 Motorcycle Security System INSTALLATION MANUAL AND USER'S GUIDE

0

Filed Under (Tips and Review) by admin on 29-01-2011

download
Routing the Antenna Wire The MCM includes an 18″ antenna wire. The first 12″ is a coaxial wire; the remaining 6″ is the reception antenna wire. When routing, try to avoid running the antenna along or near metal. For best performance, have the antenna wire as vertical as possible and exposed. Wire Connections The system includes one harness (HAR-1a) that connects directly into the MCM. The harness is split into three plugs: one for the GEN-1a connector, one for the optional SN-5 connector and one for the data output for future expansion. Note: Each plug is unique and will only fit the appropriate component one way. Main Harness Note: If the optional factory connector kit is being used, please disregard this section of the instructions and refer to the instructions supplied with the factory connector kit. The main harness consists of two harnesses. One is labeled (HAR-1a) and the second is labeled (GEN-1a). Plug in the white 4 pin connector from the (HAR-1a) into the matching 4 pin connector from the (GEN-1a). The (HAR-1a) also has a waterproof connector that plugs into the MCM. The wires should be connected as follows: HAR-1a Black wire with fuse and ring terminal – To battery Positive (+). GEN-1a Black wire – To ground (-). Orange wire – To tail light wire or any other wire that is hot (+) when ignition is ON (NOTE: this is an input to the alarm this connection is not designed to flash the tail light). Color Codes: Ground (-) Tail Light Honda Green wire Brown wire Kawasaki Black wire Red wire Suzuki Black/White Brown wire Yamaha Black wire Blue wire Harley Davidson Black wire Blue wire

Incoming search terms:

1999-2002 Indian Motorcycle Mirror Housing Removal and Replacement

0

Filed Under (Indian) by admin on 31-10-2010

download
1. Remove seat. 2. Disconnect battery. 3. Remove handlebar cover on top-center of handlebar. 4. Remove left-side clutch-bracket assembly. This exposes an access hole on the underside of the handlebar. 5. Pass the end of the Signal® mirror wires through one of the small holes located on the underside of the clutch-bracket assembly housing. 6. Take piano wire/fish tape and insert at the access hole located on the underside of the handlebar to the center of the handlebar (center handlebar cover removed). 7. Fasten the end of the Signal® mirror wires to the piano wire/fish tape and pull through the handlebars to the center opening. 8. Pull excess wire through the handlebars leaving approximately 2″ of extra wire at the mirror side. 9. Re-assemble clutch-bracket assembly allowing the Signal® mirror wire to wrap around the outside edge of the cover assembly into the underside access hole. Secure Signal® mirror with enclosed 1.5″ long 5/ 16 ” – 24 Allen head bolt. 10. Loosen throttle assembly side and slide back to expose access hole. DO NOT REMOVE THROTTLE ASSEMBLY. Proceed to pass the Signal® mirror wire through the handlebar at the opposite side and re-assemble the throttle assembly. 11. Run both sets of wires under the fuel tank along the topside of the frame to the battery compartment. 12. Connect both black wires to the enclosed ring connector for connection to the battery ground terminal. 13. Locate the male/female electrical connector that is located behind the battery. This wiring assembly is for your tail lamp assembly for braking and turning (see photo). 14. Make sure the harnesses are routed securely to the wire connectors and enough slack is left for splicing or soldering. Cut the heat shrink into (4) equal pieces (approx. 2″ each). 15. Slide the heat shrink over the passenger side Signal® mirror wire. Solder the Right Signal® mirror wire to the Brown wire. Slide the heat shrink over to cover the soldered area. Heat the shrink tube into place with a heat shrink gun or hair dryer. 16. Repeat sliding the heat shrink over the driver side Signal® mirror wire. Solder the Left Signal® mirror wire to the Purple wire. Slide the heat shrink over to cover the soldered area. Heat the shrink tube into place with a heat shrink gun or hair dryer. 17. Connect ground and positive battery connections. 18. Re-install seat.

Incoming search terms: