harley davidson CRUISE CONTROL KIT INSTALLATION

0

Filed Under (Harley Davidson) by admin on 23-02-2012

download
See Figure 1. Place a 5/32-inch (4 mm) thick insert between the brake lever and the lever bracket. 5. Refer to the service manual, and follow the instructions to loosen the brake hand lever/master cylinder assembly and remove the right-side upper and lower switch housing sub-assemblies from the handlebar. It is not necessary to remove the throttle control grip. For FLHR models: Refer to the service manual. Disconnect the left-side handlebar MOLEX socket housing from the gray eight-way main harness pin housing [24B] inside the headlamp nacelle. Refer to the service manual to remove the clutch hand lever and left-side upper and lower switch housing subassemblies from the handlebar. 6. For ALL models: See Figure 2. The friction shoe (1) is a loose fit on the end of the tension adjuster screw (2). Make sure the shoe has been removed with the switch housing sub-assemblies, and is not lodged in the groove of the throttle control grip (4). 3 4 1 2 is06318 1. Friction shoe 2. Tension adjuster screw 3. Right-side lower switch housing 4. Throttle control grip Figure 2. Throttle Tension Adjuster Screw and Friction Shoe 7. See Figure 1. Verify that the 5/32-inch (4 mm) thick insert is in place between the brake lever and the lever bracket. Obtain the new right-side handlebar switch housing assembly (Item 4 or 5, depending on model) from the kit. Separate the upper and lower halves of the housing assembly. Refer to the service manual, and follow the instructions to install the switch housing assembly and brake hand lever/master cylinder assembly to the handlebar. 8. Route the right-side switch harness along the same path as the original harness (along the right handlebar). Connect the pin housing to the black socket housing disconnected in Step 3. 9. For FLHT, FLHTC, FLHX, FLHXXX and FLTRX models: Continue at Step 11. For FLHR models: Obtain the new left-side switch housing assembly (6) from the kit. Separate the upper and lower halves of the switch housing assembly. Refer to the service manual, and follow the instructions to install the left-side switch housing assembly and clutch hand lever assembly to the handlebar. 10. Route the left-side hand control harness along the same path as the original harness (along the left handlebar). Connect the pin housing to the gray socket housing disconnected in Step 5

HARLEY DAVIDSON FXD (Dyna Super Glide) TACHOMETER KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 06-03-2011

download
1995 Models To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative cable first) before proceeding. Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 1.1995 MODELS, REMOVAL OF ELECTRONIC SPEEDOMETER AND BRACKET 1a. Refer to applicable Service Manual procedure and remove seat. 1b. Refer to applicable Service Manual procedure and remove fuel tank. Stop the engine when refueling or servicing the fuel system. Do not smoke or allow open flame or sparks near gasoline. Gasoline is extremely flammable and highly explosive, which could result in death or serious injury. (00002a) 1c. Remove speedometer sensor cable from mounting clips under tank. See Figure 1. The 3-place speedometer sensor connector [65] is located on the frame beneath the seat. Remove connector from t-stud and disconnect. Cut cable tie holding sensor wires to right rear frame tube. 1d. Refer to applicable Service Manual procedure and remove headlamp, for work clearance. 1e Remove handlebar clamp screws securing speedometer bracket. Remove speedometer, bracket, and harness. 2.1995 MODELS, DISCONNECT MAIN WIRING HARNESS 8-PLACE CONNECTOR [21B, A] (FIGURE 2) 2a. Disconnect the battery, negative cable first. Refer to applicable Service Manual procedure and disconnect main wiring harness 8-place connector [21A, B], at the front of the motorcycle. 3.1995 MODELS, REMOVE SPEEDOMETER LEADS FROM 8-PLACE CONNECTOR [21B, A] (FIGURE 2) 3a. See Figure 2 and Service Manual wiring schematic. Pull the following wires and terminals out of connector [21B]. Wire Color Cavity Number Orange/white 5 White/green 1 Black 2 3b. Remove the large female connector from the fuel gauge black wire. 3c. Slide the wires removed in step 2a out of the plastic conduit covering the wires connected to the 8-place connector. 1 WARNING 1 WARNING 1 WARNING Figure 1. Speedometer Sensor Connection [65] 4973 Speedometer sensor connector [65] Figure 2. Tachometer/Speedometer Wire Splices and Terminal Connections [21B, A] i00240-.tif Splices 4.1995 MODELS, REMOVE INDICATOR LAMPS FROM BRACKET 4a. Remove the screws that secure the indicator lamps assembly to the speedometer bracket. Retain screws and indicator lamps assembly for installation on speedometer/tachometer bracket later. 5.1995 MODELS, REMOVE SPEEDOMETER FROM BRACKET 5a. Unscrew boot from speedometer reset switch. Remove cover screws and rear cover. 5b. See Figure 3. Note position of rear speedometer gasket and remove it. Push on rear of speedometer while simultaneously pulling speedometer and front gasket from bracket. Do not remove front gasket from the speedometer. 6.1995 MODELS, INSTALL SPEEDOMETER IN KIT BRACKET 6a. See Figure 5. Place wires from speedometer through front of left opening in double bracket. Lubricate the front and rear gaskets with isopropyl alcohol or glass cleaner to ease installation. 6b. Insert speedometer into the front of the double bracket. Be sure wire guides are aligned with opening at bottom of bracket. 6c. Place rear gasket in position and align gasket tabs. Work gasket into space between speedometer and bracket by pushing speedometer against one side of bracket while pushing gasket into position at the opposite side. 6d. Add amber bulb assembly from kit to speedometer in order for tachometer and speedometer backlighting to match. 6e. Replace cover and boot from reset switch.

Incoming search terms:

HARLEY DAVIDSON SPORT WIND DEFLECTOR AND WINDSHIELD KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 03-03-2011

download
HEADLAMP VISOR INSTALLATION (2004 ONLY) 1 2 is 01467 1. Headlamp 2. Headlamp bracket mounting screws Figure 1. Remove Headlamp Mounting Screws (Left Side Shown) 1. See Figure 1. While holding the headlamp (1), remove the left and right headlamp bracket mounting screws (2). 2. See Figure 5. Obtain the headlamp visor (2) from the kit. 3. See Figure 2. Orient the headlamp visor (1) between the headlamp and headlamp mounting bracket (2) and reinstall the headlamp bracket mounting screws (3) securing the visor and headlamp to the headlamp mounting bracket. 4. Refer to the Service Manual and adjust the headlamp for the correct angle. 2 1 3 is01468 1. Headlamp visor 2. Headlamp mounting bracket 3. Headlamp mounting bracket screw Figure 2. Install Visor Between Headlamp and Mounting Bracket (Left Side Shown) 1 2 3 is03212 1. “RT” or “LFT” marking 2. Hinge-pin head faces up 3. Clamp post socket faces outward Figure 3. Fork Tube Clamp and Post Identification (Right-Side Clamp Shown) WINDSHIELD INSTALLATION 1. See Figure 5. Obtain one of the lower mount kits from the windshield kit carton. Identify the fork tube clamp for right- side (RT) or left-side (LFT) installation as indicated in Figure 3. NOTE The lower grommets (4) have been pre-installed into the Lexan┬« windshield. 2. Insert the rounded end of the post into the socket in the fork-tube clamp, oriented as shown in Figure 5. Lining up the hole in the end of the post with the hole in the clamp. With a 3 mm hex key, fasten the post to the clamp with the flat-head screw (16) from the kit, and tighten to 6.8 Nm (60 in-lbs ). 3. Place the clamp around the correct-side fork tube with the hinge-pin head facing up. Insert the two longer screws (15) from the lower mount kit through the counterbored holes in the outboard side of the clamp, and thread the screws part-way into the tapped holes in the inboard half. 4. Position the clamp so the top surface is approximately 6 to 13 mm (1/4 to 1/2 inch) below the upper triple-tree, and the hinge pin is straight forward. With a 4 mm hex key, tighten the screws just enough to hold the clamp in posi- tion. 5. Obtain the remaining lower mount kit and repeat Steps 2 through 4 to install the clamp to the opposite fork tube. 6. Obtain the upper mount kit from the windshield kit carton. NOTE The upper grommets (4), socket assemblies (3), windshield mount caps (6) and 5 mm screws (9) have been pre-installed into the windshield. 7. Place one of the handlebar clamps (5) onto one side of the handlebar, in the straight section between the riser and the handlebar controls, oriented as shown in Figure 4. NOTE Temporarily disengage the switch harness retainer from the handlebar to allow installation of the clamp.

Incoming search terms:

HARLEY DAVIDSON QUICK RELEASE DETACHABLE WINDSHIELD KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 24-02-2011

download
Installation The rider’s safety depends upon the correct installation of this kit. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00308a) NOTE Cover the front fender, headlamp and the front of the fuel tank with clean shop towels to prevent scratching. Make sure the windshield assembly does not contact chrome or painted parts. Damage to the finish could result. Turn Signal Relocation Relocate the turn signals according to instructions included in the Turn Signal Relocation Kit, item 20. Assemble the Clamps to the Windshield 1. See Figure 1. Remove the windshield sub-assembly from the packaging and place face down on a clean, soft surface with the mount brackets facing upward. 2. See the Service Parts illustration. Remove both the clamp and hardware kits from the packaging, and separate similar parts in preparation for assembly. Note that upper and lower clamps are exactly alike. 3. See Figure 2. Assemble the clamp assemblies and hardware stacks. The cupped side of the Belleville (cone) washers must face each other and sandwich the windshield mount brackets at each mount point. Failure to orient washers correctly can reduce the windshield’s ability to break away in a collision, which could result in death or serious injury. 4. See Figure 2. One clamp at a time, with the clamp facing upward and inboard of the windshield bracket (2), tighten the shoulder bolts (1) enough to hold the clamp orientation to the windshield during mounting of the windshield to the bike. The bolts will be fully tightened later. Install the Windshield NOTE Keep front wheel straight to prevent brackets from scratching fuel tank. 1. Make sure all four clamps are in the “open” position, then bring the windshield (with the clamp side away from you) to the front of the bike. 1 WARNING 1 WARNING ┬« Kit Numbers 58779-05, 57160-05 1 of 3 Figure 1. Windshield Mounting Brackets i07503 Figure 2. Windshield MountingClamp i07504 1 Shoulder bolt 2 Right windshield bracket 3 Cup washer 4 Belleville washers (cupped sides face each other with windshield bracket between)

HARLEY DAVIDSON SOFTAIL DETACHABLE WINDSHIELD INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 10-02-2011

download
INSTALLATION NOTES To prevent scratches, cover the headlamp and the front of the fuel tank with a clean cloth and be sure the windshield assembly does not contact chrome or painted parts when removing or installing it. 1. Remove the original equipment windshield, if equipped. Discard the windshield and attaching hardware. 2. See Figure 1. Remove and discard screws and washers securing trim strip (6) to the front and rear trim pieces. 3. Peel protective cover from adhesive side of clear tape. Center tape over front panel trim piece, attach tape to trim piece, wrap tape edges around trim piece and attach to back of trim piece. Leave the protective tape on the trim pieces after kit installation. 4. Install a flat washer (2), bushing (3) and thick washer (4) onto mushroom screw (1), then install the screw into the upper hole of the trim strip (6) and front and rear trim pieces. Do not tighten screw. 6 1 4 2 3 5 4 2 3 is02411a 1. Mushroom head screw (2) 2. Flat washer from kit (4) 3. Docking point bushing (4) 4. Washer, thick (4) 5. Button head screw (2) 6. Front panel trim strip Figure 1. Front Panel Trim Strip and Windshield Dock Installation 5. Install a flat washer (2), bushing (3) and thick washer (4) onto button screw (5), then install the screw into the lower hole of the trim strip (6) and front and rear trim pieces. Tighten screws to 96 in-lbs (10.8 Nm) . 6. Repeat procedures 2 – 5 on the opposite side. 7. Lock the bottom windshield assembly jaws into the grooves of the lower rubber docking bushings on each side of the front fork assembly. 8. Hook the top windshield assembly jaws into the grooves of the upper rubber docking bushings. 9. Firmly press the windshield into place until it is seated on the docking bushings. 10. Tighten the upper screws to 96 in-lbs (10.8 Nm) . Improper installation of accessories or loading of cargo can affect motorcycle stability and handling, which could result in death or serious injury. (00455b) Failure to provide adequate clearance between stationary and moving parts can cause loss of control, which could result in death or serious injury. (00378a)

1961 MODEL G2CS ELECTRICAL CONVERSION FOR COMPETITION

0

Filed Under (AJS) by admin on 31-10-2010

download
The entire electric system except the battery, ignition switch, ignition wiring and coil can be removed for off-the-highway competition. 1. Remove the saddle and gasoline tank. 2. Pull the lighting harness wires from the connectors, leaving the connectors in place, unless removal is specified. Follow the code for easiest disconnection. a. Translucent. b. Purple. c. Double Brown from four way connector and horn connector. d. Black from connector at tail lamp. e. Orange. f. Yellow – keep the connector on this wire. g. Light Green. 3. Connect the Yellow wire from the ignition harness into the double connector with the Light Green wires. 4. Pull the Brown wire at the four wire connector and at the tail lamp. Pull out and remove the stoplight harness and switch. 5. Remove the horn. 6. Disconnect the speedometer cable at the drive gearbox. NOTE: The gearbox cable socket should be taped to keep out dirt or the gearbox may be removed. Be sure to reinstall all wheel supporting and spacing parts. 7. Remove the left grip, loosen the set screw, slide the dip switch from the handlebar and replace the grip. 8. Remove the headlamp with the wiring harnesses and speedometer cable. 9. Remove the tail lamp and bracket. Service Release #6-82 (con’t) March 27, 1961 The wiring left on the motorcycle is shown on page 45 of the 1961 G2 Instruction Book. With the connections as shown, the ignition is normally from the battery but the emergency start circuit is available in case the battery becomes discharged