HARLEY DAVIDSON HIGH INTENSITY DISCHARGE (HID) DUAL BULB HEADLAMP KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 04-04-2011

download
REMOVAL 1. Remove seat according to the instructions in the service manual. Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 2. 2003-Earlier Models: Disconnect battery cables, negative (-) cable first. Refer to the service manual. To prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding. (00251b) 3. 2004-Later Models: a. Remove left saddlebag. Refer to the service manual. b. Remove left side cover and main fuse. Refer to the service manual. 4. Remove fuel tank according to the instructions in the service manual. 5. See Figure 1. Remove the Phillips screw (1) at the bottom of the bezel and remove the bezel. Save parts for installa- tion. 1 2 is03916 1. Phillips screw 2. Bezel Figure 1. Remove Bezel 6. See Figure 2. Remove and save Phillips screws (1) that secure mounting ring assembly (2) to nacelle. 7. Gently pull headlamp assembly out far enough to disconnect wiring. Save short wire harness for installation. 8. Remove wire connector at the back of the headlamp bulb. 9. See Figure 2. Remove three screws (3) securing the retaining ring (4) and headlamp assembly to mounting ring assembly. Discard mounting ring assembly, but save three screws and retaining ring for installation

HARLEY DAVIDSON VRSC TURN SIGNAL RELOCATION KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 08-03-2011

download
INSTALLATION Removing Turn Signals To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative (-) cable first) before proceeding. (00307a) Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 1. Remove the 40 amp Maxi-Fuse or disconnect the battery cables, negative cable first. Never touch the quartz bulb. Fingerprints will etch the glass and decrease bulb life. Grab the bulb with paper or a clean, dry cloth. Failure to do so could result in bulb damage. (00210a) 2. For VRSCA models, remove headlamp assembly. For VRSCB models, continue to Step 4. a. While facing the headlamp from behind (looking toward front of motorcycle), reach behind the headlamp bucket and twist the headlamp bulb approximately 45 degrees counterclockwise, then gently pull straight out of the headlamp. Repeat for remaining bulb. Temporarily secure bulbs out of the way for the following steps. b. See Figure 1. Remove the two mounting screws securing the headlamp bracket to the upper triple clamp and remove headlamp assembly. Save hard- ware

HARLEY DAVIDSON V-LOGO TURN SIGNAL INDICATOR FORROAD KING INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 25-02-2011

download
1. Disconnect battery cables, negative cable first. 2. Following instructions in applicable Service Manual, remove the windshield. 3. Remove the phillips screw at the bottom of the of the headlamp door (chrome ring). Remove the headlamp door. 4. Remove the seven Phillips screws to free the headlamp housing from the headlamp nacelle. 5. Squeeze the two external tabs (if present) to remove the wire connector at the back of the headlamp bulb. Remove the headlamp housing assembly and set aside. 6. See Figure 1. Reaching inside the headlamp nacelle, remove the speed nut to release the chrome strip at the top of the nacelle. 7. Remove the wire form clip holding the halves of the nacelle together at the bottom. 8. Carefully pry off the fork lock plate at the rear of the handlebar clamp shroud. Remove two Phillips screws beneath the lock plate. 9. Loosen the Phillips screw from the tab at the front of the handlebar clamp shroud (but do not remove). 10. Loosen the two acorn nuts from the left and right side fork studs. 11. Raise the handlebar clamp shroud slightly, and while separating the halves of the headlamp nacelle, remove the shroud from the vehicle. 12. Carefully align the template over the handlebar shroud cover and tape into place. 13. Exercising caution to avoid scratching, secure the shroud in a vise or use other suitable means. 14. Use a center punch and carefully punch the drill hole locations. See Figure 2. Make sure to punch indentation deep enough to keep the bit from skating during the drilling procedure. 15. Drill one 1/4″ hole and two 5/32″ holes as indicated on the Drill Template (attached)