Ktm CRF-230 Installation and Removal Manual

0

Filed Under (KTM) by admin on 27-01-2012

download
Partially install the headlight assembly using the top right white zip tie only to hold it in place temporarily. You will need to plug wires to this assembly. Step 5: Install handlebar switch on clutch side. You will need to move clutch perch to the right (about ½ inch to1 inch) to make room for the switch. The switch plugs into the circuit board on the bottom of the headlight using the 8-pin plug (the only unused 8-pin one on the circuit board) Step 5: (Power harness) The power wire with the two pin plug runs from the battery to the 6 inch wire hanging from the control board. The red wire should be attached to the positive and the black wire to the negative of battery. You will need to notch the battery cover so the wire can fit with the cover closed. Step 6: (Taillight harness) The wire with the six pin plug is for the tail light. Run the wire down the left side of the bike. If you plan on using a front hydraulic brake switch use the front connectors and continue at Step 7A. If you are planning on using a mechanical rear brake switch use the green pair of connectors and continue at Step 7B. You can use both

KTM EXC taillights Installation manual

0

Filed Under (KTM) by admin on 23-01-2012

download
Step1: Remove headlight, (headlight switch) seat and gas tank from KTM. Step 2: Partially install the headlight assembly using the top right band only to hold it in place temporarily. You will need to plug wires to this assembly and if you put all four bands on you will not be able to make the connections. Step 3: Install handlebar switch on clutch side. You will need to move clutch perch to the right (about ½ inch to1 inch) to make room for the switch. The red knob on the clutch adjuster should just miss the handlebar switch. The switch plugs into the circuit board on the bottom of the headlight using the 8-pin plug (the only unused 8-pin one on the circuit board) Step 4: Behind the gas tank and in front of the air box is a small rectangular hole in the frame. You will be feeding two lines with the plug ends first down through this hole. They must be fed one line at a time and you may need to use needle nose pliers to grab them and help pull them through. The lines you want to feed through this hole are the power line with two-pin molex plug and the line for the taillight with the six-pin plug. Route these wires all the way to the headlight assembly along the left side of the bike on the bottom of the gas tank frame tube. In this step we will connect the power line only. With the handlebars turned all the way to the right, plug the power wire into the back of the headlight assembly making sure to leave some extra wire so you can turn the handlebars both ways without tugging on the wires. The other end of the power line has battery terminal loops. The positive has an in-line fuse and the other black wire is the negative. Connect these to the battery.

Honda Foreman 500 And Honda Rubicon WINCH MOUNTING KIT INSTALLATION

0

Filed Under (Honda) by admin on 13-12-2011

download
Begin by removing the front skid plate located on the front of the ATV. Remove the four side 8mm bolts and four bottom 6mm bolts securing the front skid plate, figure 1. Save the fasteners as they will be used later to reinstall the front skid plate. 2. Remove the four plastic rivets on each side of the front plastic fascia, figure 2. Use a large screw driver to carefully remove the center rivet. After removing the center rivet, remove the rivet housing. Save the fasteners as they will be used to reinstall the front plastic fascia. 3. Remove the two 6mm bolts that attach the front plastic fascia to the bumper, figure 3. Remove the front plastic fascia at this time . Remove the two 6mm bolts that attach the front bumper to the plastic headlight assembly, figure 4. Save the fasteners as they will be used to reinstall the front bumper. 5. Remove the two top 8mm bumper bolts that attach the front bumper to the front rack, figure 5. Save the fasteners as they will be used to reinstall the front bumper. Figure 5 Remove Top Bumper Bolts Remove (both sides) 6. Remove the two ottom bumper bolts that attach the bumper to the bottom of the vehicle frame, figure 6. Save the fasteners as they will be used to reinstall the front bumper

Incoming search terms:

Suzuki B-King GSX1300 BK Suspension Removal and Installation

0

Filed Under (Suzuki) by admin on 01-12-2010

download
Front Fork Removal and Installation B823H12206002 NOTE The right and left front forks are installed symmetrically and therefore the removal procedure for one side is the same as that for the other side. Removal 1) Remove the front wheel assembly. Refer to “Front Wheel Assembly Removal and Installation in Section 2D (Page 2D-4)”. CAUTION ! •Make sure that the motorcycle is supported securely. •Do not operate the front brake lever with the front wheel removed. 2) Disconnect the brake hose clamp (1) from the front fender. 3) Disconnect the brake hose (2) from the brake hose clamp. 4) Remove the front fender by removing the bolts (3) , left and right. 5) Remove the reflex reflector for E-03, 24, 28, 33. 6) After removing of the headlight cover upper screws (4), move the headlight assembly forward. 7) Loose the front fork upper clamp bolt (5). NOTE •Slightly loosen the front fork cap bolt (6) to facilitate later disassembly. •Be sure to adjust the rebound damping force adjuster (7) to the softest position before removing the front fork. 8) Loosen the front fork lower clamp bolts (8) and remove the front fork. NOTE Hold the front fork by the hand to prevent sliding out of the steering stem. Installation 1) Set the front fork to the front fork lower bracket temporarily by tightening the lower clamp bolts (1) . 2) Tighten the front fork cap bolt (2) to the specified torque. Tightening torque Front fork cap bolt (a): 23 N·m (2.3 kgf-m, 16.5 lb-ft) 3) Loosen the lower clamp bolts. 4) Set the front fork with the upper surface “T” of the outer tube positioned 3.0 mm (0.12 in) “a” from the upper surface of the steering stem upper bracket. 5) Tighten the front fork lower clamp bolts (1). Tightening torque Front fork lower clamp bolt (b): 23 N·m (2.3 kgf- m, 16.5 lb-ft) 6) Tighten the front fork upper clamp bolt (3). Tightening torque Front fork upper clamp bolt (c): 23 N·m (2.3 kgf- m, 16.5 lb-ft

Plug And play professional race electronics kit for the Ducati Desmosedici RR

0

Filed Under (Ducati) by admin on 11-11-2010

download
1. Remove the headlight assembly and replace with the carbon shelf which supports the new electronics 2. Remove the standard ECU and dashboard 3. Remove the left hand 4. Weld two lambda bosses into the exhaust pipes 5. Fit the new hardware using the brackets supplied in this kit 6. Install the software on your PC 7. Calibrate the throttle and start the engine Notes: 1. This system may only be fitted to track bikes that do not require the headlights or turn signal controls. These are removed during the installation of this equipment 2. Tyre / rim size calibration is fully adjustable by the user 3. Please let us know the type of exhaust system you are using at the time of ordering. 4. When using this equipment the immobiliser system is not needed and the ignition key switch can be replaced with a standard off/on type toggle switch if required. 5. No wiring is modified during the installation of this equipment. 6. All normal starting functions are retained as well as side stand warning. Marelli SRT / MDU Copyright – Competition Systems 2010 – Specification subject to change without prior notice 3 ** Installation & support Even though we supply very good base settings, which are race proven, each bike has fundamental differences. Changes in tyres, rims, shock & fork settings, engine characteristics, track surface and rider style are only a few of the variables which may demand adjustments to the traction maps to achieve perfection & fast lap times. Within the installation & support costs the user will receive training on all of the following: • System structure and overview of hardware • Mapping techniques – how to get the best from your engine • Traction control system – how it works & how to program it • Launch control – how it works & how to program it • System mapping & closed loop control • Calibration & control of system inputs & outputs • Use of all software applications and PC setup • Data analysis techniques This course is estimated at 3-4 days and will require the bike to be fully installed with the new hardware prior to the visit, and have a dyno available for part of the demonstrations if mapping training is required. A track day is also essential for developing a custom TC setup.

Ducati streetfighter HID headlight system installation Manual

0

Filed Under (Ducati) by admin on 26-10-2010

download
The installation of this kit requires the removal of the Helmholtz air box between the air intakes, located directly in front of the main air box. You will also need to run a wire from the front of the bike to the back of the bike where the battery is located. 1. Remove the seat, tail section, and fuel tank. 2. Remove the headlight assembly. 3. Replace the headlight bulb with the included HID bulb. You will need to modify the cap for the back of the headlight to allow the wires to pass through. 4. You will need to mount the Ballast, igniter, and the relay for the switch box in the area where the Helmholtz was. (see image) 5. Run the red power wire to the back of the bike and connect directly to the positive lead on the battery terminal. 6. Connect the ground wire the frame where the Helmholtz was previously bolted. 7. Plug the HID bulb into the ballast. There are 3 plugs. They can only be connected one way. 8. Connect the main wire harness to the ballast. 9. Turn the key on and turn the ignition on and check that the headlight comes on. 10. Switch on the brights to make sure this is working as well. 11. Once everything is confirmed to be working make sure the wirings are well attached won’t interfere with the fan or with any of the steering components. 12. Re-install the tank, tail section, and seat

Ducati SPORT TOURING HEADLIGHT UPGRADE INSTALLATION AND REMOVAL INSTRUCTIONS

0

Filed Under (Ducati) by admin on 25-10-2010

download
1. Remove the following fairing components per the instructions in the Ducati owners manual: • Instrument surrounds • Headlight fairing • Chin fairing (under headlight/air intake) • Right-side middle fairing (covers battery) 2. Disconnect the speedometer cable from the speedometer. Unthread the ring nut at the top of the speedometer cable and retract the cable downward about 4-6 inches. 3. Disconnect the headlight wiring from the headlight bulbs. Retract the rubber boots at the rear of the headlight assembly to gain access to the wire terminals. Note that the two ¼ inch terminals at the high- beam bulb have locking clips that should be depressed before pulling the terminal away from the bulb. 4. Unplug the parking light from the headlight body by grasping the wires and carefully pulling it out. 5. Remove the two rubber plugs covering the lower headlight mounting screw access holes beneath the air intake horn. 6. Using an 8mm hex socket inserted through the lower access holes remove the two hex-head bolts securing the bottom of the headlight to the frame. 7. Using the same socket wrench, remove the two 8mm hex-head bolts securing the top of the headlight assembly to the frame. 8. Remove the headlight assembly from the frame. 9. Remove the two rubber grommets and steel reducing sleeves from the frame at the top mounting locations for the headlight. Leave the lower pair in place; these will be re-used, as shown in Figure 6

Incoming search terms: