HARLEY DAVIDSON CHROME FORK COVER KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 30-01-2011

download
INSTALLATION OF KIT 66440-05 1. Kit 66440-05 , Loosen the fuel tank. Refer to FUEL TANK- PARTIAL REMOVAL in the appropriate section (carbureted or EFI Engine) of the Service Manual. 2. Disconnect the headlight connector from the main harness. 3. Start with one side and remove the screws fastening the trim strip and rear triple clamp cover. Remove trim strip and rear triple clamp cover. Repeat procedure for other side. 4. Remove the nut, washers, lockwashers and bolt holding the headlight housing to the tripletree. Retain all hardware for future use. Remove headlight housing. 5. Remove front panel. 6. See Figure 2. From kit, place front panel (1) into position. 7. Install headlight using the bolt, washer, lockwasher and nut removed earlier. Tighten fastener. Refer to your service manual for torque specifications and headlight alignment procedures. 8. Insert headlight wiring through hole (2) in front panel and connect wiring to main electrical harness. When servicing the fuel system, do not smoke or allow open flame or sparks in the vicinity. Gasoline is extremely flammable and highly explosive, which could result in death or serious injury. (00330a) 9. Install fuel tank. Refer to FUEL TANK-PARTIAL REMOVAL in the appropriate section (carbureted or EFI Engine) of your Service Manual. 10. Start with the left side and install the chrome rear triple clamp cover (4), and trim strip using screws removed earlier. Tighten fasteners. 11. Install the headlight switch thru switch hole (5) removed earlier. 12. Install the chrome right side rear triple clamp cover (3) and trim strip and tighten fasteners

WY50QT-30A SPECIFICATION AND OWNER MANUAL

0

Filed Under (Tips and Review) by admin on 21-11-2010

download
Meter and indicator light (Fig3) ⑴ Odometer ⑵ Speedo meter ⑶Fuel meter ⑷Parking light ⑸Right Turning signal light ⑹Voltage Meter ⑺Left Turning signal light (8) High-Low beam light ⑼Time meter Ignition Switch(Fig4) (1) On ()-when the switch turn to this position, Start engine and do not pull out the key. 。 (2) Off () When the switch turn to this position, Start engine power off and take out the key. ⑶ Lock () When the switch turns to lock position () , Take out the key .do not do any turning operation And do not start engine and light. 。 Notice : If the engine is idling speed for a long time in the hot climate, It will appear too hot Phenomenon Must close engine. Fig3 Fig 4 6 Fuel Meter(Fig 5) 1.Fuel Meter (Fig 5) show the approx remainder of flue. When the hand point to (F), it indicates Full tank of 7.5L. 。 2.When the hand at red section it indicates the remainder of flue is 1.8L. Headlight Switch (1) (Fig 6) Headlight switch: three position”" 、”"and”•” :When it on the position, the front head light, tail light, position light and meter light turn on. :When it on the position, tail light, position light and meter light turn on. •:When it on the position, the front head light, tail light, position lighted instrument turn off. Starting Switch (2) (Fig 6) Press this button to start engine(Ref.P16)

Incoming search terms:

KYMCO MXU 500 SPECIFICATION AND OWNER'S MANUAL

0

Filed Under (Kymco) by admin on 12-11-2010

download
OFF ON (1) CONTROL FUNCTIONS 17 (1) Ignition switch (2) Key IGNITION SWITCH ON: Functions oft he respective switch positions areas follows: The key cannot be removed. Theenginecanbe started. OFF: “”: All electrical circuits are switched off except hazard light. The key can be removed in this position. All electrical circuits are switched on. The ignitions witch is ON while the position light and taillightwill light. All electrical circuits are switched on. Theenginecanbe started. The key cannot be removed. 18 INSTRUMENTS AND INDICATOR (1) Multi-function display (2) (3) (5) (6) Low-range indicator light”L” (7) High-range indicator light”H” (8) Neutral indicator light”N” (9) Reverse indicator light”N: (10) Park indicator light”P” (11) (12) Right turn signal indicator High beam indicator (4) Coolant temperature warning indicator Set button Mode button Left turn signal indicator (11) (2) (3) (4) (5) (8) (1) Multi-function display The display includes the following functions: Speedometer Odometer/Tripmeter Digital clock 2WD/4WDindicator Fuel gauge (2) Right turn signal indicator Flashes when the right turn signal operates. (3) High beam indicator The ignition switch is at the”"position, the high beam indicator will light when the headlight switch to select High beam () . Both left and right turn signal indicator will flash at the meantime when the hazard switch is operated and turn signal switch is turned off. NOTE: (12) (1) (7) (6) (9) (10) TRIP ODO mile kmPM 2WD 4WD SET MODE PRNHL
19 (4) Coolant temperature warning indicator When the coolant temperature reachesa specified level, this indicator comes onto warn that the coolant temperature is too hot. If the indicator comes on during operation, stopt he engine as soon as it is safe to do so and allow the engine to cooldown for about 10 minutes. (5) Set button This button is used to select ODO, TRIP A andT RIPB. This button is also used to adjust the time and reset the tripmeter. (6) Low-range indicator light”L” This indicator light comes on when the drive select lever is in the”L”position. (7) High-range indicator light”H” This indicator light comes on when the drive select lever is in the”H”position. (8) Neutral indicator light”N” This indicator light comes on when the drive select lever is in the”N”position

Incoming search terms: