KAWASAKI VULCAN 900 SLASH CUT STAGGEREDS INSTALLATION MANUAL

0

Filed Under (Kawasaki) by admin on 02-05-2012

download
1. Attach mounting bracket 440-P to frame using two stock fl ange head bolts used on stock upper bracket (Figures 1 and 2). 2. Remove head pipes and heat shields from protective packaging. Place each heat shield on a non-abrasive surface such as a blanket or carpet. Using a felt tip pen, mark outside edge of each heat shield to show location of mounting clips that hose clamps will loop through (Figure 3). 3. Lay front header, and rear header into their head heat shields and muffl er body heat shields. 4. Install #20 hose clamps (supplied) on heat shields and #36 (supplied) on muffl er body heat shields by feeding tail end of clamps into heat shield clips (fi gure 3). Take note of clamp screw head direction (Figure 4). Screw heads must be accessible when system is installed on motorcycle for adjustment purposes. NOTE: Do not tighten at this time. 5. Using stock fl ange nuts, carefully install head pipes into exhaust ports. Assistance may be required. NOTE: Do not tighten at this time. 6. Slide nut plates inside bracket that is welded to backside of muffl er bodies (Figure 5). While holding nut plates in place, attach muffl er bodies to mounting bracket 440-P using two 5/16″x 5/8″ fl ange head bolts (supplied). Leave them loose at this time. 7. Align muffl er bodies so they are level and parallel when viewing from the right side of the bike. Tighten cylinder port exhaust fl ange nuts on front and rear cylinders. 8. Tighten the fl ange bolts on both muffl ers. 9. Tighten all heat shield clamps. 10. Check for adequate clearance of all exhaust system components and motorcycle accessories prone to heat damage. NOTE: For models with fl oorboards, two Spacer washers are supplied to space out the fl oorboard bracket enough to allow the fl oorboard to fold up without hitting the heat shield. 11. Be sure to tighten all hardware before starting your motorcycle. 12. After installation and before starting motorcycle, completely clean pipes and muffl ers with cleaning solvent and a clean, soft cloth that will not leave a residue. NOTE: Any residue, oil, or fi ngerprints will stain the chrome when the metal heats up

HARLEY-DAVIDSON SOFTAIL CROSSOVER REMOVAL AND INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 01-04-2012

download
EXHAUST SYSTEM REMOVAL READ ALL INSTRUCTIONS BEFORE BEGINNING 1. Under the oil tank on the right hand side, locate the rear O² sensor connector. Unplug sensor and feed the end of wire through the frame freeing it from motorcycle. NOTE: Pay attention to wire routing for re-installation. 2. Open the plastic cover above the rectifier on front of the frame to access to the front O² sensor connector. Unplug sensor from harness. Remove ZIPSTRIP holding wire to frame and feed the wire through freeing it from motorcycle. 3. On floorboard equipped models, loosen the right hand floorboard mounting bolts to gain clearance for exhaust removal and installation. 4. Loosen the heat shield clamps on both front and rear exhaust pipes. 5. Remove the mounting nuts from each head pipe, located at the cylinder head. 6. Remove the nuts attaching the exhaust mount bracket to the frame. 7. On FLSTD and FLSTF models, you will need to remove the right side passenger foot peg and hanger, as this is attached to the exhaust mount bracket. Replace the passenger foot peg assembly using the BOLT 14 Allen bolt (supplied). 8. Remove the entire exhaust system and set it aside. 9. Remove the two lower mounting studs from the frame See figure 1 . Recommended replacement exhaust port gaskets, H-D P/N: 65324-83A. 10. Carefully remove exhaust port flanges and circlips from the stock exhaust system using snapring pliers. See figure 2 . NOTE: Replace bent or damaged circlips. Check exhaust port gasket condition. 11. Remove O² sensors from stock head pipe and set aside for re-installation on your new RUSH exhaust system. PAGE 1 OF 4 RUSH RACING PRODUCTS EXHAUST SYSTEM INSTALLATION P/N 7020 – 7120 BEFORE INSTALLATION PLEASE READ ALL INSTRUCTIONS 1. Remove header and heat shields from protective packaging. Place each heat shield on a non-abrasive surface such as a blanket or carpet. Using a felt tip pen, mark outside edge of each heat shield to show location of mounting clips that hose clamps will loop through See figure 3. 2. Apply a small amount of anti-seize compound to the threads of the O² sensors and install them into the new head pipe. NOTE: Be careful not to get anti-seize on sensor tip, it may affect sensor function. 3. Install circlips and flanges from stock system onto the new head pipe See Figure 2. Note: Replace circlips if bent or damaged 4. Attach BRKT-007 to frame using two BOLT 12 Tighten to factory specs. 5. Install complete assembly into exhaust ports (rear port first). Use stock flange nuts, Do Not Tighten .

YAMAHA V-STAR 650 CA SHORTSHOTS STAGGERED INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 29-12-2011

download
Check condition of stock exhaust gasket. Replace if damaged or worn. 2. Install mounting bracket (stamped 384-P) in the original bracket mounting position using two 8mm bolts (supplied)(Figure 1). Note: Install two 5/16″ x 5/8″ fl ange bolts (supplied)(Figure 1) into top holes of bracket before installing bracket onto motorcycle. 3. Mark outside surface of front and rear heat shields with location of mounting clips that are welded to the inside (Figure 2). Place each heat shield on a non abrasive surface such as a blanket or carpet. Lay each head pipe/muffl er onto its respective heat shield (Figure 3). 4. Loosely install each hose clamp by feeding tail end of clamp into heat shield clip (Figure 2). #20 hose clamps are for head pipes and #28 hose clamps for muffl er area. Take note of clamp screw head direction (Figure 4). Screw head should be accessible when system is installed on motorcycle for adjustment purposes. Note: Do not tighten yet. 5. Install 6″ fl ange bolts (supplied) engaging nut plate. Leave T-bolt clamp onto front muffl er (Figure 4&5). Slide muffl er onto front head pipe. Slide nut plate (supplied) inside bracket welded to backside of front muffl er (Figure 6). Attach muffl er to mounting bracket 384-P using two 5/1head pipe/muffl er assembly loose at this time. 6. Using stock Allen bolts, carefully install rear head pipe/ muffl er assembly into exhaust port. (Assistance may be required). Note: Do not tighten yet. 7. Slide nut plate (supplied) inside bracket welded to backside of rear muffl er (Figure 6). 8. Align muffl ers so they are parallel when viewed from the right side of the motorcycle and muffl er tips align at the same length. Tighten 5/16″ fl ange bolts securing muffl ers to bracket. 9. Tighten cylinder exhaust port bolts securing head pipes to cylinder head. 10. Tighten T-bolt clamp securing front muffl er to head pipe. 11. Adjust heat shields so that muffl er tips protrude 1/4″ from heat shields (Figure 7) and rotation of heat shield matches muffl er tip. Tighten all hose clamps securing heat shields. 12. After installation and before starting motorcycle, completely clean pipes and muffl ers with cleaning solvent and a clean, soft cloth that will not leave a residue. Note: Any residue, oil, or fi ngerprints will stain the chrome when the metal heats up. 13. All hardware must be properly tightened before starting motorcycle

HONDA VTX 1300 Retro BIG SHOTS EXHAUST SYSTEM INSTALLATION

0

Filed Under (Honda) by admin on 07-12-2011

download
Check condition of stock exhaust gaskets. Replace if damaged or worn. 2. Install and tighten supplied mounting bracket (stamped
346-P) in the original mounting bar location, using two M10x40 flange bolts, nuts, and washers (supplied) (Figure 1). 3. Install and tighten rectifier using M6x30 flange bolt, nut, and washer combinations (supplied)(Figure 1). 4. Place heat shields on a non-abrasive surface such as a blanket or carpet. Using a felt tip marker, mark the outside surface of front and rear heat shields with the location of the mounting clips welded inside(Figure 2). 5. Install each heat shield over its respective head pipe (Figure 3). 6. Install each hose clamp by feeding tail end of clamp into heat shield clip. Take note of clamp screw head direction (Figure 2 & 4). Screw head should be ccessible when system is installed on motorcycle for adjustment purposes. Use #20 hose clamps for head pipe areas and #28 hose clamps for muffler areas. Note: Prior to tightening hose clamps, align end caps so that slash ends are even.

HONDA AERO 750 CRUZER EXHAUST SYSTEM REMOVAL And INSTALLATION

0

Filed Under (Honda) by admin on 18-11-2011

download
Install mounting bracket (stamped 363-P) in the original muffler mounting position, using two 10mm bolts and
one 10mm nut. (supplied)(Refer to figure 2). 2. Mark outside surface of front and rear heat shields with location of mounting clips that are welded to the inside.(Refer to figure 3).Place each heat shield on a non-abrasive surface such as a blanket or carpet. Position each head pipe/muffler over its respective heat shield. (Refer to figure 4).
3. Feed tail end of each hose clamp through each mounting clip welded to back side of front and rear heat shields. Take note of clamp hex screw head direction. (Clamp head direction is critical for adjustment when system is installed on bike.) Wrap each clamp around back side of head pipe threading tail end into clamp head. (Refer to figure 3 & 4).
4. Install front head pipe/muffler using stock flange nuts. Slide dog bone shaped nutplate (supplied) inside
bracket welded to backside of muffler. Attach muffler to mounting bracket 363-P using (supplied) 5/16” flange
bolts engaging dog bone nutplate. Leave head pipe/muffler assembly loose at this time (Refer to figure 4). Repeat this step with the rear head pipe.5. Align mufflers so they are parallel when viewing from right side of the motorcycle. Tighten 5/16” flange bolts securing upper and lower muffler positions.. Tighten cylinder exhaust port flange nuts securing head pipes to cylinder heads. 7. Adjust heat shields so they meet front of muffler taper. (Refer to figure 6). Tighten all hose clamps securing heat shield locations. NOTE: Heat shields should cover muffler/head pipe weld joint.

HONDA VTX1800R AND HONDA VTX1800N BIG SHOTS EXHAUST SYSTEM REMOVAL

0

Filed Under (Honda) by admin on 17-11-2011

download
If motorcycle is oxygen sensor equipped, unscrew the sensors from the stock exhaust system and install them
into the Vance & Hines exhaust system, being sure to install the front cylinder sensor into the lower pipe and
the rear cylinder sensor into the top pipe. Note: Use caution when handling. Do not touch sensor tip area.
2. If motorcycle is not oxygen sensor equipped, install both M12 x 11 plugs and washers (supplied)into the oxygen
sensor bosses. 3. Check condition of stock exhaust gaskets. Replace if damaged or worn. 4. Install and tighten supplied mounting bracket (stamped 345-P) in the original mounting bar location, using one M10 x 35 flange bolt and nut on top (supplied) and one M10 x 20 flange bolt on bottom (supplied) (Figure 2). Note: The bracket mounts behind the top frame mount and in front of the bottom frame mount(Figure 2).5. Install and tighten rectifier using M6x30 flange bolt, nut
and washer combinations (supplied) (Figure 2). 6. Place heat shields on a non-abrasive surface such as a blanket or carpet. Using a felt tip marker mark outside surface of front and rear heat shields with location of the mounting clips welded to the inside

Incoming search terms:

HONDA SHADOW AERO 750 STRAIGHTSHOT HS EXHAUST SYSTEM

0

Filed Under (Honda) by admin on 03-11-2011

download
Install mounting bracket (stamped 359-P) in the original bracket mounting position, using two 10mm bolts and
one 10mm nut (supplied)(Figure 2). 2. Remove head pipes and heat shields from protective packaging. Place each heat shield on a non-abrasive surface such as a blanket or carpet. Using a felt tip pen, mark the outside edge of each heat shield to show location of hose clamp mounting clips (Figure 3). 3. Slide flanges onto head pipes and lay head pipes into
heat shields. Loosely install hose clamps by feeding tail end of clamp into heat shield clips (Figure 3). Take note of screw head direction (Figure 4). Screw head should be accessible when system is installed on motorcycle for adjustment purposes. Use #20 hose clamps for head pipe areas and #28 hose clamps for muffler areas.
4. Using stock nuts, carefully install head pipes into exhaust ports (Assistance may be required). NOTE: Do not tighten at this time.

HARLEY DAVIDSON TLE/TLE-ULTRA SIDECAR ATTACHMENT KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 13-03-2011

download
REMOVAL NOTES Refer to the service manual for more information on these generalized steps. Save all removed parts (unless otherwise noted) for installation of this kit or for motorcycle operation without the sidecar. 1. For TLE-Ultra Models: Remove both lower fairings. 2. Remove the bolt and lockwasher securing the right passenger footrest bracket and remove the bracket with footrest. 3. Remove the three right side exhaust heat shields. Some models may require removal of the right side exhaust pipes. 4. Remove stock clutch cable. 5. Remove rear master cylinder/rear brake pedal assembly. Remove rear brake pedal from master cylinder assembly. Remove and save rubber pedal pad and brake pedal. Discard cotter pin. 6. Cut the cable straps holding front oxygen sensor connector to frame bracket. 7. Remove wire harness/brake line clip from right lower frame tube. INSTALLATION New Clutch Cable Installation 1. Refer to the service manual and follow instructions to remove stock clutch cable. 2. Refer to the service manual and follow instructions to connect the new clutch cable to clutch hand lever. 3. For FLHT/C/CU: Follow the instructions in the service manual to route new clutch cable through fairing. 4. For FLHR/C Models: Capture the cable in a clamp at the left upper passing lamp bolt. On FLTR models, capture the cable in a clamp at the left upper bolt securing the speedometer and tachometer housing to the upper fork bracket. These locations are identical with stock cable routing. 5. See Figure 1. Route clutch cable down along left frame downtube (1). 6. Continue to route cable down between left front engine isolator and crankcase. Clutch cable will cross to the right side of motorcycle beneath the crankcase, to the clutch release cover on the right side of the transmission. 7. Install clutch cable fitting into clutch release cover. Refer to the service manual. NOTES The final positioning and attachment of the clutch cable and clutch cable adjustment will be performed after sidecar mounts have been installed. Verify that the clutch cable and the rear brake line do not make contact. Damage could result. 1 2 3 is05785 1. Downtube 2. Clutch cable 3. Route clutch cable behind left front engine iso- lator Figure 1. Route Clutch Cable Relocating Oil Pressure Sending Unit NOTES Perform this procedure on all models equipped with an oil pressure gauge or Police models. All other models proceed to “Master Cylinder Assembly/Rear Brake Pedal Modification.” 1. Remove cable strap securing oil pressure wire harness to frame. 2. Locate the latch on connector to oil pressure sender (next to lower right frame downtube). Raise latch on connector and disconnect connector from oil pressure sender. 3. Remove the oil pressure sender using a 1-1/16 inch open- end crowfoot wrench. 4. See Figure 16. Coat threads of elbow (44) with Loctite 565 and install into crankcase oil pressure sender threads. 5. See Figure 2. Install elbow (1) until snug so open end is in the five-o’clock position (2). Do not over-tighten or crankcase may be damaged. 6. Coat threads of oil pressure sender with Loctite 565 and install into 90 degree brass elbow. Use a 1-1/16 inch open- end crowfoot and tighten to 96-120 in-lbs (11-14 Nm) . 7. Install connector on oil pressure sender unit. Verify that slight clearance to the right engine isolators is present. Adjust position of elbow as required to provide clearance

HARLEY DAVIDSON SPORTSTER BLACK EXHAUST HEAT SHIELDS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 14-02-2011

download
INSTALLATION Remove Original Equipment (OE) Heat Shields Avoid contact with exhaust system and wear protective clothing that completely covers legs while riding. Exhaust pipes and mufflers get very hot when engine is running and remain too hot to touch, even after engine is turned off. Failure to wear protective clothing could result in burns or other serious injury. (00009a) 1. Allow the motorcycle to cool. 2. Identify the position of the OE clamp screws securing the black heat shields to the exhaust pipes. NOTE The clamp screws are positioned on either side of the exhaust pipe for clearance. 3. See Figure 1. Open the heat shield clamps (1) and spread the bands to remove front and rear heat shields (2) from the exhausts. Retain the heat shield clamps Install Black Heat Shields 1. See Figure 2. Matching the OE position of the heat shield clamps, open the clamps bands and thread the bands through the brackets of the front (1) and rear (2) black heat shields. 2. Spread the band around the exhaust pipes and push the end of the bands to engage the clamp screws. Tighten to hold the heat shields in place. 3. Adjust the shields and heat shield clamps to access clamp screws and to avoid contact with other components. 4. Tighten the heat shield clamp screws

Incoming search terms:

KAWASAKI VULCAN 700/750 CRUZER EXHAUST SYSTEM INSTALLATION MANUAL

0

Filed Under (Kawasaki) by admin on 28-12-2010

download
REMOVING THE STOCK EXHAUST SYSTEM 1. Place the bike on the center stand. 2. Remove the three clamps attaching the heat shield to the left hand head pipe and set the heat shield aside. 3. Remove the two heat shield clamps attaching the heat shield to the right hand head pipe and set the heat shield aside. 4. Loosen the pinch clamps where the mufflers slip onto the muffler box (the black box in front of the rear tire). Remove the bolt attaching the mufflers to the footrest. 5. Remove the left and right hand mufflers and set them aside. 6. Remove the right hand foot rest and brake pedal assembly from the frame. 7. Loosen the pinch clamps where the head pipes slip into the muffler box. 8. Remove the two nuts that secure the right head pipe to the cylinder head. Repeat this step on the left head pipe and save the nuts for reuse. 9. Remove the left and right hand head pipes. Remove the header flange from each head pipe and save the two flanges for reuse. Set the head pipes aside. 10. Remove the two bolts (one on each side) that mount the muffler box to the frame. Lower the muffler box down and set it aside. INSTALLING YOUR NEW VANCE & HINES EXHAUST SYSTEM 1. Remove the two bolts from the charcoal canister mount, the canister is located in front of the rear tire. Using the two 6mm x 16mm bolts (supplied) install the centerstand stop bracket, (stamped 205), by aligning the holes in the bracket with the holes in the canister mount. Be sure the bend closest to the holes in the bracket angles towards the rear of the motorcycle and the tang is pointed to the left hand side. Tighten the two 6mm bolts at this time. 2. Unscrew all of the hose clamps (supplied) until they are completely loose. Feed the tail end of the hose clamp into the clips on the inside of both heat shields. Place the front head pipe into the heat shield, wrap the hose clamp around the head pipe and give the screw three to four turns. Repeat this step with the rear heat shield. Note : The screw end of the hose clamp should be accessible, but not visible when pipe is mounted on the bike. Leave them loose at this time. 3. Install a three hole mounting bracket to each muffler as shown in figure 1. Slide one dog bone shaped nut plate under the bracket that is welded to the backside of each muffler. Attach the mounting bracket using two of the 5/16″ flange head bolts (supplied), leave them loose at this time. Note : The muffler bracket stamped #284 is for the right hand muffler, bracket #285 is for the left hand muffler. 4. Install the rear exhaust assembly, with the heat shield attached, to the rear cylinder using the stock flanges and nuts. Install the stock muffler mounting bolts through the rear footrest brackets, the supplied muffler brackets, and finger tighten the nuts. Leave them loose at this time. 5. Repeat step #4 with the front head pipe

Incoming search terms: