Harley-Davidson FL Models (1993-2009) HARLEY PASSENGER FLOORBOARD COMFORT KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 17-04-2012

download
1. Using your 5/16″ allen wrench, unscrew the Cap head allen bolts attaching the stock passenger floorboard mount to the frame and remove the assembly. You will reinstall this assembly once the mounts have been installed. STOCK MOUNT FEATURES: Notice the floorboard mount has a locating pin that protrudes from the rear surface. This pin is what keeps the mount from swiveling on the frame. The frame has three threaded holes and one unthreaded hole on each side. These holes provide the three different floorboard heights the bike offers stock. HEIGHT POSITIONS: The Comfort Kit mounts provide you the ability to raise the stock floorboards height 1-1/4″ or 2″ higher than the highest stock position. This is accomplished by attaching the mounts to the specific combinations of the threaded holes on the frame. POSITION #1 – Raises the floorboards 2″ by attaching the mounts to the #1 & #2 threaded holes from the top. NOTE: You must use the rectangular spacer block in order to use the 2″ rise position in order to clear the right exhaust pipe. POSITION #2 – Raises the height 1-1/4″ by attaching the mounts to the #2 & #3 thread holes from the top. TILTING: You will notice one threaded and one unthreaded hole towards the top of each mount and directly between these holes is an engraved L & R. These mounts are Left and Right side specific. The locating pin mentioned in the stock mount features paragraph inserts into the unthreaded hole and locks the floorboard into its tilted position.

Incoming search terms:

HARLEY DAVIDSON PASSENGER FOOTPEG MOUNTING KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 30-01-2011

download
This passenger footpeg mounting kit fits 1993 and later FLT, FLHT, FLHS, and FLHR model motorcycles. See Service Parts illustration below for items contained in this kit.Installation 1. On each side of the motorcycle, remove the socket head capscrew and lockwasher that attaches each footboard bracket and footboard to motorcycle. Remove both footboard brackets along with their footboards. 2. See Service Parts illustration. Place each footpeg support (2-right side, 3-left side) in position (the supports can be installed in one of two different height positions to suit passenger preference) and securely fasten to motorcycle with lockwasher and capscrew removed in step 1. 3. Install footpegs (sold separately) on each footpeg support using capscrews (1), spring washers (4), and locknuts (5). The spring washer goes between the jaws of the footpeg supports along with the mounting end of the footpeg. Tighten hardware securely. NOTE If footpeg supports are properly installed, footpegs will point 45˚ (from vertical) toward rear of motorcycle. Footpegs must fold up at a 45˚ angle (from vertical) toward rear of motorcycle. This angle allows footpegs to fold up if they accidentally strike the ground when making a sharp turn. Failure to install footpegs with the proper fold-up angle could result in death or serious injury.

YAMAHA ROAD STAR PASSENGER FLOORBOARD RELOCATION ARMS INSTALLATION INSTRUCTONS

0

Filed Under (Yamaha) by admin on 23-12-2010

download
1. If you are installing Relocation Arms and Passenger Floorboards, install the floorboards first per their instructions. When installing the Relocation Arms with Passenger Floorboards already installed proceed as follows. 2. Starting on the LEFT side, fold the floorboard up. Remove the socket head bolt which secures the floorboard to the motorcycles stock peg support and remove the floorboard taking notice of which pinholes the dowel pins are located in. 3. Locate the Relocation Arm that has an “L” stamped on the backside of it. Place two of the supplied dowel pins into one of the two sets of the pinholes in the backside of the arm that are directly across from one another. (180 degrees apart.) Place the arm onto the mounting block and align the pins in the arm with the holes closest to the desired height you wish the floorboard to be at. Bolt the arm to the mounting block loosely using one of the supplied 5/16″ X 1″ button head bolts. 4. Place the Passenger Floorboard with its two dowel pins into the set of pinholes at the other end of the relocation arm that allows the floorboard to be parallel (horizontal) to the ground. Use one of the supplied 5/16″ X 3/4″ socket head bolts to mount the floorboard to the relocation arm and make finger tight. 5. Install the RIGHT side in the same manner. Check to see that the right arm is at the same height and/or position as the left. Bolt the floorboard to the other end of the arm using the remaining dowel pins and socket head bolt. Tighten all four bolts on both sides securely. NOTE: Four other height positions are possible by using the other sets of holes on the front side of the mounting block and backside of the relocation arm

Incoming search terms:

Incoming search terms: