Harley-Davidson Hard mount installation Manual

0

Filed Under (Harley Davidson) by admin on 12-04-2012

download
1. It is recommended that you create a template from cardboard or heavy paper (not included) of the back of the bag to assist in proper placement on the motorcycle. The template can be used for both bags simply by flipping it over horizontally 180 degree for slant style bags. For all other saddlebags transfer template to other bag making sure that the hole pattern corresponds with the bolts pattern on the opposite fender strut. 2-Assemble the saddlebags support 2. Remove your existing fender strut mounting bolts. 3. (A*) Install replacement 8mm x 70mm or 10mm x 70mm bolts. (Most Harley-Davidson models will utilize the 8mm bolts. Please determine which bolts will fit your specific application prior to assembly. Your make and model of motorcycle may require additional hardware. (See your motorcycle owner’s manual). 4. Install 2 upright and secure tight enough to maintain position and secure with the lock nuts (Metric applications do not require lock nuts). Ensure that bracket angles are away from the bike. 5. Lightly apply a dab of engine oil and lightly coat the exposed bolts(C or D) and barrel bolt Hex- head (E) assemblies (Mark at 4 points for each saddlebag). You can also use a marker or pen to mark. Take the template or bag and place against the brackets. Hold and press firmly to transfer the oil to the bag or template. The oil will leave a mark on the bag or template. If you are not satisfied with the position of the bag wipe the oil off and repeat as many times as necessary. Note: Position according to your specific setup, ensure the bag will not contact hot engine or exhaust components. If planning on carrying a passenger, ensure that there is enough clearance for the passenger’s legs between the bags and the foot pegs. Make sure that the uprights DO NOT contact moving parts, including but not limited to suspension components. 6. Place the Saddlebag on a firm surface and drill 4 holes (make sure you drill holes according to the size of the bolt to be passed) into the back of the bag only, according to your oil drop pattern. Also be careful not to damage the large mesh pocket inside the saddlebag. If a template was utilized cut the corresponding holes into the template and place temple on the back of the bag and drill following above directions. The template can be utilized for both sides of the bag

Incoming search terms:

Harley Davidson FLH EZ-Steer Installation MANUAL

0

Filed Under (Harley Davidson) by admin on 22-03-2012

download
Installation of the Champion EZ-Steer system is similar to the installation of the OEM triple clamp of your Harley Davidson FLH Motorcycle. We recommend that you use an OEM service manual and follow the prescribed disassembly, installation and torque specifications for the upper and lower clamp assembly. Before Installing Kit (2008 & Prior) The wiring bracket of the OEM upper triple clamp needs to be modified to fit the Champion upper triple clamp. After removing / disassembling the OEM parts from your motorcycle, position the OEM wiring bracket onto the Champion upper clamp as shown. Scribe the ID of the steering stem hole onto the wiring bracket and enlarge the hole to scribe line. This will allow the wiring bracket to fit over the new Stem Lock-Nut. Install OEM handle bar mount assemblies to Champion upper clamp using Item #5 (Handle Bar Mount Spacer). The spacers are used on top of the upper clamp. Installation Notes • Be sure to use the correct fork extension. Yellow 2002 and newer (non adjustable air pressure). Black for 2001 and older (adjustable air pressure). Be sure to double check the fork cap (Fork Tube Plug) being removed. • Reinstall the OEM O-rings on Item #7 (Fork Extensions) prior to installing in the fork tubes. • On some of the Road King models with chrome headlight Nacelle, Item #9 must be mounted underneath upper clamp Item #2 to ensure enough room for air fittings. • Be sure to replace fork covers in proper order, during installation of the fork tubes. • Thoroughly clean sides of steering neck and install self adhering rubber stops where steering stop screws contact frame. • Secure wires and cables clear of steering stop bolts. • Do not torque Item # 1 (½-20 x 1-1/4″ Hex Head Bolt) until fork tubes have been installed to assembly. • Note the torque specification for the items listed in the table below.

HONDA TRX 450R Nerf Bar INSTALLATION AND REMOVAL INSTRUCTIONS

0

Filed Under (Honda) by admin on 23-12-2011

download
Parts List: Quantity Part 1 Nerf Bar Left 1 Nerf Bar Right 2 Hex Head Bolt, M10 x 70mm 2 Flat Washer, M10 2 Hex Head Bolt, M6 x 16mm 2 Flat Washer, M6 4 Net Clips 1 Net Set 2 Footpeg Washer 2. Preparation: a) Set/Lock rear parking brake on bike, turn gas petcock to ‘Off’ position and stand bike upright so that it is sitting on the rear grab bar. Make sure vehicle is secure and will not fall over while installing your new Nerf Bars. 3. Installation: a) Install Hardware & Web Strap per photo’s: NOTE: Loosely install all hardware and tighten when complete. Torque M10 Bolts @ 30 ft. lbs. Torque M6 Bolts @ 8 ft. lbs. REMOVE & REUSE OEM BOLTS TO ATTACH FOOT PEG. ATTACH FOOT PEG TO NERF SUPPORT USING M6 X 16MM HEAD BOLT AND WASHER. ATTACH NET CLIPS NOTE: FIRST SLIDE LEFT NERF WELDED TUBE INTO RIGHT NERF TUBE THEN, LOOSELY ATTACH FRONT NERF BARS TO THE A-ARMS USING OEM NUTS AND SUPPLIED M10 X 70MM BOLTS AND WASHERS

Honda VTX 1800 Motorcycles Trike Conversion Installation Manual

0

Filed Under (Honda) by admin on 19-12-2011

download
Removal of Original Parts Secure and raise the motorcycle 9 to 10 inches using a quality motorcycle lift. Remove the following from the vehicle. See OEM manual for detailed instructions. Items to be retained for reinstallation after modification are noted. · Rider’s Seat (to be re-installed without modification) . · Passenger Seat and mounts (to be reinstalled without modification) . NOTE: OEM front and rear seat mounting bolts to be retained and reused. · Left and right passenger foot rests and mounts (to be reinstalled with modification) . · Mufflers (to be re-installed and relocated with minor modification) . · Rear Fender (complete w/ sub frame and all attaching parts) . · Swing Arm, Drive Shaft and Rear Wheel (complete w/ brake line and all attaching parts) Installation of Champion Trike Conversion Kit 3.1 Modify Frame and Passenger Footrests. a. Use 17/64″ drill and drill through frame from inside out using passenger footrest mount holes as guide. b. Enlarge the passenger footrest mounting holes on the left and right side of the frame to 27/64″. c. Enlarge the holes in the left and right passenger footrest mounting plates to 27/64″. d. Clean area of all debris. 3.2 Relocate Regulator a. Install supplied “Z” bracket to the regulator as shown using the supplied hardware. b. Attach regulator to frame using the supplied hardware. c. Tie hoses down to avoid contact with the swing arm. Qty Description 1 ¼-20×2 hex head bolt 1 ¼-20×1-1/4 hex head bolt 6 ¼-20 Nyloc nut 10 1/4- SAE flat washer 4 as spacers 3.3 Hose Stay a. For models that have a recover tank below the swing-arm, a holder has been included keep the hose connected to the water pump away from the champion swing-arm. b. Remove the hose from the top of the recovery tank. c. Push the water pump hose forward against transmission. d. Secure hose with supplied stay as shown using existing bolt. Ensure that hose is not being crushed. Bend stay if necessary. e. Reconnect hose to recovery tank

HARLEY DAVIDSON SOFTAIL LEFT SIDE LEATHER TOOL BOX KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 19-04-2011

download
Installation While handling and installing tool box, be careful not to scratch surface. 1. See Service Parts Illustration. Install tool box (1) to mounting bracket (6) using button head screws (2) and washers (5). Screws (2) should be inserted through mounting holes on inside of tool box (1) and then inserted through bracket (6) holes and threaded into weld nuts attached to bracket. 2. Remove and save the two screws that secure left rear fender support to motorcycle frame. 3. Remove two bolts, nuts, and washers that secure debris deflector to motorcycle frame. This will allow you to move debris deflector out of the way when installing new passenger footpeg support bolt. Save hardware for reinstallation. 4. For 1990 to 1999 Softails: If tool box is being installed with passenger footpeg, remove the hex head bolt and left passenger footpeg. Retain footpeg and lockwasher for reinstallation. Discard bolt . If tool box is being installed without passenger footpeg, remove hex head bolt and left passenger footpeg. Discard footpeg. Retain bolt and lockwasher. For 2000 and later Softails: See page 3 . Remove footrest from clevis. Remove clevis from frame by removing cap screw from center of clevis. If tool box is installed with footpegs, keep all hardware. If toolbox is to be installed with footboards, discard hardware. 5. Slide top of mounting bracket (6) between rear fender support and frame. Align top holes in bracket with fender support holes. Align lower bracket hole with footpeg mounting hole in frame. Install the two screws, removed in Step 2, in fender support. Do not tighten screws at this time. 6. For 1990 to 1999 Softails: Place lockwasher retained in step 4 on footpeg support hex head bolt (3) from kit. CAUTION 1 of 3 For 2000 and later Softails with footpegs: Install kit 49352-00 according to instructions included in this kit. Footpeg must fold up at a 45°angle (from vertical) toward rear of motorcycle. This angle allows footpeg to fold up if, by accident, it strikes the ground surface when making a sharp turn. Failure to set footpeg to the proper fold-up angle could result in death or serious injury. 7. For 1990 to 1999 Softails: Position footpeg so it folds up and back at a 45°angle. Install bolt (3) from kit through frame, tool box bracket (6), and spacer (4), into footpeg, as shown. NOTE If vehicle is equipped with saddlebag support bracket, Part No. 90346-90 or 90346-94, position saddlebag support bracket between tool box bracket and spacer.

Incoming search terms:

HARLEY DAVIDSON SOFTAIL CHROME LOWER BELT GUARD INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 13-04-2011

download
REMOVING STOCK PLASTIC LOWER BELT GUARD 1. See Figure 1. Remove the hex head bolt (2), washer (3), acorn nut (5), hex head screw (4) and acorn bolt (8) attaching plastic belt guard to rear fork. 2. Remove the plastic belt guard. Save fasteners (2), and (4), washer (3), acorn nut (5) and acorn bolt (8) for installing new chrome belt guard. INSTALLING CHROME LOWER BELT GUARD 1. See Figure 2. Position the new chrome belt guard from kit over belt. Align the holes in guard with mounting lugs on rear fork. Install acorn bolt (9) through mounting lug and fasten to belt guard. Finger tighten only. 2. Install screw (4) with washer (5, from kit) through belt guard and fasten to threaded mounting lug. Position the guard for adequate clearance and finger tighten screw. 3. At the upper belt guard, install the original forward hex bolt (2) and original washer (3) through the upper guard (1), then through the upper hole in chrome belt guard and through mounting lug on rear fork. Secure with original acorn nut. 4. Tighten all hardware to 110 in-lbs (12.4 Nm)

Incoming search terms:

HARLEY DAVIDSON DYNA DOCKING HARDWARE FOR FXDX WITH WIDE TIRE INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 05-04-2011

download
Installation NOTE Perform the following procedures on one side of the motorcycle until instructed to go to the other side. To keep fender in alignment the front docking point will be mounted first. INSTALLING DOCKING POINTS NOTE Save the acorn nuts and washers removed from the fender support bracket for use when installating docking points. 1. Loosen and remove the acorn nuts, washers, and screws from the fender support (right-hand) bracket. Save the washers and acorn nuts for docking point installation. Discard screws. 2. Obtain 1 plastic bushing, labeled 01, from a bushing set. 3. Place the bushing (4) (beveled side out) into the front support hole as shown in Service Parts illustration. 4. Place the countersunk side of the front docking point (2) so that it engages bushing (4). 5. From underneath (inside) the fender, insert hex-head screw (1) through fender, support bracket and front docking point (2). 6. Install washer (7) split lockwasher (5) and acorn nut (6) to screw and tighten to 27 ft-lbs (37 Nm). Take care to avoid scratching or marring component finish. 7. Obtain another plastic bushing, labeled 01 , from the bushing set. 8. Place bushing (4) (beveled side out) into the the rear support hole as shown in Service Parts illustration. 9. Place the countersunk side of the rear docking point (3) so that it engages bushing (4). 10. From underneath (inside) the fender, insert hex-head screw through fender, support bracket and rear docking point (3). 11. Install washer (7) split lockwasher (5)and acorn nut (6) to screw and tighten to 27 ft-lbs (37 Nm). Take care to avoid scratching or marring component finish. 12. Repeat procedures 1 through 11 for opposite (left-hand) side of the motorcycle. NOTE In time docking points may wear, causing the sideplates to become loose. The fit may be tightened using the following procedure. 1. Loosen docking hardware. 2. Rotate docking points clockwise approximately 45°. 3. Tighten docking hardware to the appropriate torque values. Repeat as often as required, up to 3 times

Incoming search terms:

HARLEY DAVIDSON LEFT SIDE TOOL BOX KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 06-03-2011

download
INSTALLATION NOTE While handling and installing tool box, be careful not to scratch surface. 1. See Figure 1. Attach the toolbox (4) to the toolbox mounting bracket (1) using the three pan head screws (2) and Nylock nuts (3) from the kit. 2. Remove the two button head screws (I) which secure left rear fender support (B) to motorcycle frame (C). Retain screws for reassembly. 3. On models with passenger footpegs: a. For FLSTN models: Remove button head screw (N) and left footrest bracket (O) with attached footrest support (F) and footrest (E). b. For all other models: Remove the locknut (G), hex head bolt (J), spring washer (H) and footpeg (E). Remove the socket head cap screw (K) that secures the footrest support (F) to the frame (C). c. Remove the two bolts, nuts and washers which secure the bottom of the splash guard to the swingarm. This will allow you to move splash guard when installing the new passenger footrest bolt. d. Retain all removed components. 4. On models with passenger footboards: a. Remove the screw securing the passenger footboard assembly to the frame. Remove the footboard assembly. b. Retain all removed components. 5. Slide the top of mounting bracket (1) between rear fender support (B) and frame (C). Align top holes in bracket with fender support holes. Align lower bracket hole with footrest mounting hole in frame. Install the two screws (I), removed in Step 2, in fender support. Do not tighten screws at this time. Footrests must fold up and toward rear of motorcycle if struck. Failure to set footrests to fold up and back could result in death or serious injury. (00366a) 6. On models with passenger footpegs: a. For FLSTN models: Install button head screw (N) and left footrest bracket (O) with attached footrest support (F) and footrest (E) on top of the toolbox bracket (1). Tighten screw to 35-45 ft-lbs (47.5-61.0 Nm). b. For all other models: Refer to instructions in footpeg extension kit, Part Number 49352-00 for installation, and install the extention kit, footrest support and footpeg on top of the toolbox bracket (1). c. Install the two bolts, nuts and washers and secure the bottom of the splash guard to the swingarm. 7. On models with passenger footboards: a. Position footboard assembly, in the same orientation as removed, on top of tool box bracket. b. Install screw removed in Step 4. Tighten to 35-45 ft- lbs (47.5-61.0 Nm)

HARLEY DAVIDSON AIR WING SADDLEBAG LID RAIL LIGHTS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 23-02-2011

download
INSTALLATION 1. If saddlebag rails have not yet been installed: Perform the Air Wing Saddlebag Rail installation up to the point of final assembly of the rails to the saddlebag lids. If saddlebag rails are already installed: Open one saddlebag and remove all loose contents. Remove one saddlebag from the vehicle per service manual instructions. From the underside of the saddlebag lid, remove the fasteners retaining the saddlebag rail to the lid. Note fastener position and save all components for installation. 2. ALL installations: See Figure 3. Obtain a saddlebag rail light assembly (1) from the kit. 3. Insert the light wires through the hole (B) in the side of the saddlebag rail (A) mounting post, and out through the bottom of the post. 4. Install the light to the underside of the saddlebag rail rear cross bar with two screws (4) from the kit. Tighten the screws >securely. 5. Insert the light wires through the left rear saddlebag rail mounting pad (C) and the left rear hole (H) in the saddlebag lid (G). Assemble the saddlebag rail to the lid per the instructions in the Air Wing Saddlebag Rail Kit, feeding the wires through the left rear saddlebag rail nylon washer (D), plain washer (E) and the hex head hollow screw (F). Tighten the two Phillips head screws to 27-31 in-lbs (3.1- 3.5 Nm) . Tighten the hex head hollow screw to 30-50 in- lbs (3.4-5.6 Nm) .

Incoming search terms:

HARLEY DAVIDSON HANDLEBAR POLYURETHANE RISER BUSHING KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 20-02-2011

download
INSTALLATION NOTES • Cover fuel tank with blanket or towels to keep paint from being scratched. • See the Touring Service Manual for the Fairing Removal procedure in order to gain access to the handlebar assembly. 1. For Touring Models: See Figure 1. Remove and save the the existing capscrews (C). Remove the handlebar assembly (A) and carefully allow gauges and handlebar to rest on motorcycle. Remove and discard cup washers (D), rubber bushings (E) and spacers (F). Install the new bushings. For All Models Except Touring: Remove and save the two capscrews (C) from underneath the upper fork bracket that hold the existing lower clamps (risers) (B) in place. Remove the handlebar assembly (A) and carefully allow gauges and handlebar to rest on motorcycle. Remove and discard the existing cup washers (D), rubber bushings (E) and spacers (F). NOTE The upper bushing and lower bushing must be oriented with flat side opposite from each other as shown. 2. Install the new polyurethane riser bushings (1) in place of the removed cup washers, bushings, and spacers. 3. Align components as shown in Figure 1. 4. Secure components with two hex head capscrews removed in Step 1. Insert the capscrews, from the bottom, thru the upper fork bracket, thru the bushings (1) and into the clamps (risers). See the service manual for the torque specification. 5. See the service manual and install the handlebars

Incoming search terms:

Incoming search terms: