Yamaha TDM 900 Disconnecting the battery ground REMOVAL AND INSTALLATION

0

Filed Under (Yamaha) by admin on 29-01-2012

download
Remove the seat. • Disconnect the battery ground (negative terminal). Remove the fairing side panels. • Remove the four marked hex screws with plastic washers. Note the positions the screws come from as they are not all the same. • Note that the bottom, rear hex bolt has a retaining plastic washer INSIDE the fairing. The long bolt goes under the ‘twin’ label. • Remove the hex screw indicated on the inside of the fairing panel. • Remove the grey Phillip’s head screw as indicated on the inside panel. • Remove the plastic locking clip on the underside of the fairing behind the radiator.

Incoming search terms:

HARLEY DAVIDSON LOWER FORK BRACKET (TRIPLE TREE) COVER KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 13-03-2011

download
Installation 1. For models equipped with air baffle: See Figure 1. Remove and discard the two hex screws (2) and flat washers (3) holding the baffle (1) to the fork stem and bracket assembly(4). Retain the baffle for later reassembly. For models not equipped with air baffle: Remove and discard the two plugs from the rear of the fork stem and bracket assembly (4). 2. Remove and discard the hex socket head screw (6) holding the brake line manifold (5) to the underside of the fork stem and bracket assembly. 3. Place the lower fork bracket cover into position covering the brake line manifold. Attach the cover (and the baffle, if so equipped) to the fork stem and bracket assembly with the two 1/4″ self-tapping hex screws from the kit. Tighten securely. 4. Install the 5/16″ self-tapping hex socket screw through the cover and brake line manifold into the stem and bracket assembly. Torque to 10-15 ft-lbs (13.6-20.3 Nm). 5. Verify that the throttle and clutch cables are routed properly and do not interfere with steering the vehicle. After disturbing the brake system, BEFORE moving motorcycle, you must pump brake fluid until the pistons push the pads against the brake disc. If you don’t pump fluid pressure up again, the brake will not be available to stop the motorcycle which could result in death or serious injury. After disturbing the brake system, always test motorcycle brakes at low speed. If brakes are not operating properly, or braking efficiency is poor, testing at high speeds could result in death or serious injury

HARlEY DAVIDSON AUTOMATIC PRIMARY CHAIN TENSIONER INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 29-01-2011

download
1. Refer to the appropriate Service Manual and remove seat. To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) 2. Disconnect negative (-) battery cable. 3. Refer to the appropriate Service Manual and remove primary cover. 3 1 2 5 4 is00561 1. Screw (2) 2. Anchor plate 3. Nut and washer 4. Manual tensioner 5. Screw (2) Figure 1. Manual Tensioner: 1985-2000 Models 4. For 1985-2000 model motorcycles, remove manual tensioner and replace the carriage bolt as follows: a. See Figure 1. Remove two screws (5) and nut and washer (3), and remove chain tensioner (4). b. Remove two screws (1) and anchor plate (2). c. Replace the carriage bolt in the anchor plate with the carriage bolt from the kit. d. Apply 2-3 drops of Loctite 262 (red) to the threads of the anchor plate mounting screws (1), then install anchor plate and two screws. Tighten screws to 12- 14 ft-lbs (16-19 Nm) . For 2001 and later model motorcycles, remove manual tensioner as follows: a. See Figure 2. Remove nut and washer (1) and remove chain tensioner (2) Removing the Autotensioner for Service 1. Use a tie wrap and secure the shoe to the base of the autotensioner, without securing it to the autotensioner bracket. This will retain the autotensioner adjustment for reinstallation during service. 2. Remove two autotensioner hex screws, and autotensioner. Resetting the Autotensioner 1. See Figure 5. Compress autotensioner wedge (1) and spring back to the base. 2. Hold wedge in position by inserting a hex wrench or pick tool through the hole in the base of the autotensioner. 3. See Figure 6. Move plastic autotensioner shoe (1) into place as shown. 4. If available, install shipping plate (2) to secure the shoe to the base. If it is not available, secure the shoe to the base with a tie wrap

Incoming search terms: