2006 2007 Yamaha R6 Front Brake Line Kit INSTALLATION

0

Filed Under (Yamaha) by admin on 25-05-2011

download
Identify the key components that complete our brake line kit: You should have two (2) hoses, one (1) double banjo bolt, two (2) single banjo bolts, and one (1) zip ties. There are also a total of nine (9) washers. Seven (7) will be used, and two (2) are spares. Step 2: To ensure no paint damage from a brake fluid spill, completely cover the front end of the bike. This process can be messy, and brake fluid WILL drip! Step 3: After drying out the OEM brake system, uninstall stock hoses. Take note of how the stock system was routed in case you need to re-install it. Please note there is a plastic shield on the lower triple clamp of most models; we took this piece off to ease installation. Step 4: Install the right and left (to your right and left as you sit on the bike) lines to the calipers, using the shorter line on the right side. These lines will travel from the master cylinder to the calipers; a double banjo bolt is included to run two lines down. The positioning sequence on the master cylinder is as follows: Double banjo hex, washer, 40-degree banjo labeled for right line, washer, 20-degree banjo labeled for left line, washer, master cylinder. Please see picture A for reference! Double banjo bolts must be torqued at 12 FT pounds.

HARLEY DAVIDSON V-LOGO REAR FENDER TRIM RAIL INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 17-02-2011

download
INSTALLATION NOTE All models for which this kit is designed are equipped with a original equipment (stock) fender rail or bumper. Remove the stock bumper and install the kit rail using following the proce- dures. 1. See Figure 1 and Table 1. Install V-logo (4) to trim rail (1) with hex washer screws (3) and lock washers (2). 2. Reach under rear edge of fender and remove locknut (A) and washer (B). Retain locknut and washer and use to mount new trim rail. 3. Loosen and remove the two screws (C) and locknuts (D) which attach fender rail to saddlebag support bracket. Retain screws (C) and locknuts (D) and use to mount new trim rail. 4. Place new trim rail in position and install washer (B), locknut (A), screws (C) and locknuts (D). 5. Tighten locknut (A) to 45-85 in-lbs (5.0-9.6 Nm) and locknuts (D) to 15-20 ft-lbs (20.3-27.1 Nm) . SERVICE PARTS 2 3 4 1 A B C D is05379 Figure 1. Service Parts: V-Logo Rear Fender Rail Table 1. Service Parts Part Number Description (Quantity) Item Not Sold Separately Trim rail, rear fender 1 7115 Lock washer (2) 2 7611 Hex washer screw (2) 3 91112-94 V-logo 4 Items mentioned in text, but not included in kit. Locknut (2) A Washer (2) B Screw (2) C Locknut (2)

2007 Yamaha R1 Front Brake Line Kit Installation instructions

0

Filed Under (Yamaha) by admin on 27-01-2011

download
To ensure no paint damage from a brake fluid spill, completely cover the front end of the bike. This process can be messy, and brake fluid WILL drip! Step 3: After drying out the OEM brake system, uninstall stock hoses. Take note of how the stock system was routed in case you need to re-install it. Step 4: Install the right and left (to your right and left as you sit on the bike) lines to the calipers, using the shorter line on the right side. These lines will travel from the master cylinder to the calipers; a double banjo bolt is included to run two lines down. The positioning sequence on the master cylinder is as follows: Double banjo hex, washer, 40-degree banjo labeled for right line, washer, 20-degree banjo labeled for left line, washer, master cylinder. Double banjo bolts must be torqued at 12 FT pounds. (See picture A for sequence) Step 5: Route brake lines below the stock lower triple clamp, and zip tie them together. This will ensure your lines stay in position as the steering moves. Also, make sure the lines are secured beneath the steering stabilizer rod. (See picture C) Step 6: Before installing the lines onto the right and left calipers, replace the OEM bracket with the enclosed “C-clip”. Route the hose through the new bracket and thread the single banjo bolts at each caliper using the following sequence: 20-degree banjo, washer, single banjo bolt, washer, thread into caliper. Torque banjo bolts to 12 FT pounds. (See picture B) Before you proceed to the next step, please check for clearance of the lines. Compress the front end to make sure that the lines are not binding with anything. When the front end is fully extended or fully compressed, double check that the lines are traveling correctly and clear from any obstructions. Step 7: Bleed brake system according to owner’s manual, and build appropriate pressure. Keep in mind your master cylinder is equipped with it’s own bleeder nipple. Finish with Galfer DOT-4 brake fluid

2008 SUZUKI GSXR1300 Hayabusa Front Brake Line Kit INSTALLATION INSTRUCTIONS

0

Filed Under (Suzuki) by admin on 09-01-2011

download
Step 1: Identify the key components that complete our brake line kit: You should have two (2) hoses, one (1) double banjo bolt, and two (2) single banjo bolts. There are also a total of nine (9) washers. Seven (7) will be used, and two (2) are spares. We strongly suggest having a professional mechanic install these brake lines, and all other installations void warranty. Step 2: To ensure no paint damage from a brake fluid spill, completely cover the front end of the bike. This process is messy, and brake fluid WILL drip! Step 3: After drying out the OEM brake system, uninstall stock hoses. Take note of how the stock system was routed in case you need to re-install it. Please note there is a plastic shield on the lower triple clamp of your machine; we took this piece off to ease installation. Remove the OEM hose holder, and keep the bolt for later use. (See picture C) Step 4: Install the right and left (to your right and left as you sit on the bike) lines to the calipers, using the shorter line on the right side. These lines will travel from the master cylinder to the calipers; a double banjo bolt is included to run two lines down. The positioning sequence on the master cylinder is as follows: Double banjo hex, washer, straight banjo labeled for right line, washer, 12-degree banjo labeled for left line, washer, master cylinder. Please see picture A for reference! Double banjo bolts must be torqued at 12 FT pounds. Step 5: Route both brake lines through the enclosed c-clip, and attach to the lower triple clamp using the bolt from the OEM holder. (See picture B) Drop the lines down and thread the single banjo bolts at each caliper using the following sequence: single banjo hex, washer, 20-degree banjo, washer, thread into caliper. Torque banjo bolts to 12 FT pounds. Before you proceed to the next step, please check for clearance of the lines. Compress the front end to make sure that the lines are not binding with anything. When the front end is fully extended or fully compressed, double check that the lines are traveling correctly and clear from any obstructions