2006 KTM 250 SX-F 250 EXC RACING 400 EXC RACING 450 SX, XC, EXC RACING 525 SX, XC, EXC RACING, REPAIR MANUAL

0

Filed Under (KTM) by admin on 05-05-2012

download
Hot start lever (250 SX-F) If you pull the red hot start lever [1] during the starting procedure backward, a bore in the carburetor will be opened through which the engine may take in additional air. The result is a „lean” fuel-air mixture of the type needed for hot starts.
ENGLISH 7 OPERATION INSTRUMENTS » Headlamp switch (EXCUSA) In this model the headlamp is switched on with the pull switch [1] . Flasher switch The flasher switch is a separate unit and is mounted on the left portion of the handlebar. The wire harness is designed in a way that whenever you want to use your bike off-road, you can dismount the entire turn indicator system without affecting the function of the remaining electrical system. Flasher left Flasher right Starter button (EXC) Pushing the black starter button [2] will actuate the E-starter. Emergency OFF switch (EXC Australia) The red emergency-OFF switch [3] is arranged adjacent to the throttle grip. In this position, the E-starter is operational and the engine can be started. In this position, the E-starter and ignition circuits are interrupted.The E-starter cannot be actuated, and the engine will not start, not even if you attempt to start it with the kickstarter. Pushing the black starter button [4] will actuate the E-starter. 2 3 4 5 6 Indicator lamps The green control lamp [5] flashes in the same rhythm as the flashing indicator when the indicator is working. The blue control lamp [6] lights up when the high beam is on

Incoming search terms:

YAMAHA RX10H/ RX10SH RX10MH/ RX10MSH/ RX10RH/ RX10RSH SERVICE AND OWNER’S MANUAL

0

Filed Under (Yamaha) by admin on 27-04-2011

download
Throttle override system (T.O.R.S.) If the carburetor or throttle cable should malfunction during operation, the T.O.R.S. will operate when the throttle lever is released. The T.O.R.S. is designed to interrupt the ignition and keep the engine revolution speed between 2,800 and 3,000 r/min if the carburetor fails to return to idle when the lever is released. Speedometer unit The speedometer unit is equipped with the following: a digital speedometer (which shows riding speed) an odometer (which shows the total distance traveled) a tripmeter (which shows the distance traveled since it was last set to zero) warning indicators (which show self-diagnosis, cool ant temperature, fuel level, and oil level warnings) fuel meter (which shows the fuel remaining in the fuel tank) grip/thumb warmer heat level indicator  (which shows the heat level of the grip warmer or the thumb warmer) After the engine is started, the tachometer 1 makes one sweep, and the warning light 2 and all segments of the meter 3 turn on and off once. Then the warning light turns on again, and then goes off if there are no problems. The grip warmer heat level is initially displayed for 5 seconds, then switches to the fuel meter display. Odometer and tripmeter modes Pushing the select/reset button 4 switches the display between the odometer mode “ODO” and the tripmeter mode “TRIP”. To reset the tripmeter, push the select/reset button for at least one second while the tripmeter is displayed. NOTE: @ To switch the speedometer, odometer, and tripmeter displays between kilometers and miles, select the odometer mode “ODO”, and then push the select/reset button 4 for at least 10 seconds. ESU00363 High beam indicator light The high beam indicator light 1  comes on when the high beams of the headlights are switched on. (See page 5-12 for headlight beam switch operation.)

YAMAHA FZS6W OWNER’S MANUAL

0

Filed Under (Yamaha) by admin on 27-04-2011

download
Indicator and warning lights EAU11030 Turn signal indicator lights “ ” and “ ” The corresponding indicator light flashes when the turn signal switch is pushed to the left or right. EAU11060 Neutral indicator light This indicator light comes on when the transmission is in the neutral position. EAU11080 High beam indicator light This indicator light comes on when the high beam of the headlight is switched on. EAU11250 Oil level warning light This warning light comes on when the engine oil level is low. The electrical circuit of the warning light can be checked by turning the key to “ON”. If the warning light does not come on for a few seconds, then go off, have a Yamaha dealer check the electrical circuit. NOTE: ● Even if the oil level is sufficient, the warning light may flicker when riding on a slope or during sudden acceleration or deceleration, but this is not a malfunction. ● This model is also equipped with a self-diagnosis device for the oil level detection circuit. If the oil level detection circuit is defective, the following cycle will be repeated until the malfunction is corrected: The oil level warning light will flash ten times, then go off for 2.5 seconds. If this occurs, have a Yamaha dealer check the vehicle. EAU11423 Coolant temperature warning light “ ” This warning light comes on when the engine overheats. When this occurs, stop the engine immediately and allow the engine to cool. The electrical circuit of the warning light can be checked by turning the key to “ON”. If the warning light does not come on for a few seconds, then go off, have a Yamaha dealer check the electrical cir

HONDA CT 70 Owner's Manual

0

Filed Under (Honda) by admin on 23-04-2011

download
INSTRUMENT AND INIHCATOH LAMP Speedometer I) is located on the headlight case and odometer 2′. incorporated in the speedometer indicates total distance travelled. Gear speed range indicators l’_§t‘- are Curved bare shown on the Epeeciometer dial plate to indicate the recommended operating range of the respective gears. High beam indicator lamp tredi i is located at the right side of the speedometer. This lamp will he on when headlight is on high beam. mph
‘.1_ Speedometer -fgi Odometer -Ffij Gear speed r.|nge indicators L @ High boom indicator lamp I “5′ Page 13 I  ELECTRICAL CONTRUIB I lGilTIUi’~l SWIICH The ignition switch is located on the left side of the main pipe. Functions of the respective 5″.’t'lt’C|’t positions are shuvvn in the chart helovv. t lgtttttttn sti, |tch Kev position I unction ii] OFF Slfitigiertzttrical circuit I5 opened, engine ‘t.’t.’||| not I3. Electrical circttit is closed, engine can be started {for day time operattioni 4 Eiectrical circuit is closed, engine can be “-3 started {for night time operation? Key removal Key can be
removecl Kev can not be removed Kev can not he removed age 14 10 0 HEADLILIHT BEAM CDH’TROL SWITCH The headlight beam control switch {D is located on the left handle grip. “L” is low beam position llow beam light and tail light on]. “H” is high beam light and tail light on. The headlight will only operate when the ignition switch is in the on posi- tion. Reler to ignition switch page 9.eat “$2, i 1| ma‘ ‘ aw Lg; Headlight beam contxul switclr -”‘ @ “I.” position {ii “ll” position , ._ _. i HORN BUTTON This is a push button switch Q) to-zated on the right handte grip. When the horn button switch is depressed the horn wlll operate

Incoming search terms:

HONDA GL1500 Headlamp Adjustments Manual

0

Filed Under (Honda) by admin on 08-04-2011

download
Headlamp Adjusting Procedure Tools needed • Long, slender #1 Phillips screwdriver (for adjusters behind the rubber plugs) • #2 Phillips screwdriver (for the other adjuster screw) • 12-inch square of cardboard • Flat wall or garage door • Paper, tape, marker NOTE: All adjustments are very fine. You have to turn the screws A LOT to see changes in adjustment. This procedure is best done after dark, because you will need to do some test rides. Preparation 1. Set the bike on its center stand, 10 feet away from an unobstructed wall or garage door, and square to the wall or door. 2. Remove the front fairing cover and lower vent grille to gain access to the headlamp adjusters. 3. Idle the engine or connect a battery charger to the battery, to prevent battery drain. Headlamp assembly viewed from the front, showing positions of mirrors and adjusters (pretend the lens has been removed) . Low Beam Vertical Alignment 1. With the lights on low beam, cover the right half of the lamp assembly with the cardboard square, so only the left bulb is shining on the wall. 2. Using a marker, mark the top of the left low beam on the wall (use paper taped to the wall if you don’t want to mark the wall itself) . 3. Move the cardboard so it blocks the left bulb, so only the right bulb is shining on the wall. 4. The top of the right low beam should be even with the mark you made for the left low beam. If it’s not, adjust by turning the screw behind the rubber plug at the top of the lamp assembly, using a long, slender #1 Phillips screwdriver. 5. Move the cardboard back and forth between the bulbs to verify that the low beams are at the same height. On high beam, the two hotspots should line up vertically. High Beam Vertical Adjustment 1. With the lights on high beam, note the position of the beams’ hot spots on the wall in relation to the mark you made in step 5 above. 2. Most owners complain about their low beams being too low on the roadway. To correct this, lower the high beams by turning the screw behind the rubber plug at the bottom of the headlamp assembly, using a long, slender #1 Phillips screwdriver. You can watch the high beam hot spot being lowered on the wall in relation to the mark you made. 3. Take a test ride. Get out on a dark street, and adjust the high beams using the dash knob until you like what you can see. Then switch to low beam and see how that looks. 4. Repeat these steps until you get the low beam pattern you want. Left/Right Adjustment 1. Back to the wall. Set the bike on its center stand at a distance of 25 feet from the wall and square to the wall. Center the front wheel. 2. Shine the high beams on the wall. 3. Step to the back of the bike, and level your eye with the center of the passenger backrest. Use the center of the backrest and the center of the windshield like a gunsight. The center of the hotspot of the high beam should hit the wall in this line. 4. Adjust by turning the uncovered screw at the bottom of the headlamp assembly, using a #2 Phillips screwdriver.

Incoming search terms:

DRAG SPECIALTIES MINI SPEEDOMETER WITH LED INDICATOR LIGHTS INSTALLATION INSTRUCTIONS

0

Filed Under (Tips and Review) by admin on 29-01-2011

download
1. Place the motorcycle on a level and secure area. Disconnect the battery. 2. Refer to the appropriate factory service manual and remove the OEM speedometer and indicator lights. The indicator lights usually unplug either in the rear of the headlight or under the gas tank area. 3. Mount the new speedometer in the desired location. 4. Locate the OEM wire for the high beam indicator light. Connect it with the blue wire from the wire harness on the speedometer. Connect the blue/black wire from the speedometer to ground. 5. Locate the OEM wire for the gauge illumination (back) lighting. Connect this wire to the orange wire on the speedometer. Connect the black wire on the speedometer to ground. 6. Locate the OEM wires for the turn signals. Usually they are brown and violet wires. NOTE: You will notice only one bulb for the turn signals in the gauge and two wires from the bike to the harness. If you connect both of these wires directly to the yellow wire on the speedometer, this will allow feedback and cause all the signals to flash at once. To prevent this, you will need to add a diode between each OEM turn signal wire and the yellow wire coming from the speedometer. We recommend that you utilize a Dyna tach adapter, Part #D-101, available separately. This tach adapter includes the diodes necessary to allow the turn signal indicator light to operate correctly. Follow the instructions for the tach adapter, substituting the wires from the original wire harness found in step 6 for the two ignition terminals shown in the wire schematic. Hook the white wire on the tach adapter to the yellow wire for the turn signal indicator on the speedometer. If you use the D-101 adapter, skip steps 7-9 and go directly to step 10. 7. Take one of the diodes, making sure to observe the correct polarity, and attach it to the brown turn signal wire on the bike. 8. Take the remaining diode, again making sure to observe the correct polarity, and attach it to the violet turn signal wire on the bike

Incoming search terms:

DUCATI MONSTER 696 Owner's manual and maintenance manual

0

Filed Under (Ducati) by admin on 14-12-2010

download
instrument panel (fig. 4) 1) LCD (see page13). 2) Tachometer (rpm). Indicates engine revs per minute. 3) Neutral (N) indicator ( green ). Illuminates when the gearbox is in neutral. 4) Fuel warning light ( yellow ). Illuminates when there are approximately 3litres of fuel left in the tank. 5) Turn signal indicator light ( green ). Illuminates and flashes when the turn signal is in operation. 6) Engine oil pressure warning light ( red ). Illuminates when engine oil pressure is too low. This light should illuminate when the ignition is switched to ON and should go out a few seconds after the engine starts. Important If this light (6) stays on, stop the engine to avoid serious damage. 7) High beam warning light ( blue ). Illuminates when the high beam headlight is on. 8) “EOBD engine diagnostics light” ( amber ). The engine ECU iluminates this light steadily to indicate the presence of errors leading to engine lock. 9) OVER REV indicator lights . Illuminates steadily at 800 rpm before intervention of the revlimiter. Starts flashing when the rev limiter is reached. 5 8 2 4 9 3 1 6 7 fig. 4 12 E 10) 2-position switch A and B . Switch used for displaying and setting instrument panel parameters. It has two positions, A “▲” and B “▼”. 11) High beam headlight flasher switch (fig. 5). The high beam headlight flasher switch is also used for the LAP and USB data aquisition functions. 11 A 10 B fig. 5 13 E LCD – Main functions Warning Any adjustments to the instrument panel must only be carried out when the motorcycle is stationary. Never operate the instrument panel controls while riding the motorcycle. 1) Speedometer . Indicates road speed. 2) Odometer . Shows total distance travelled. 3) Trip meter . Indicates the distance travelled since last reset. 4) Fuel reserve trip counter . Shows distance travelled on reserve fuel. 5) Clock . 6) Air temperature indicator . 7) Lap time . 8) Rev counter (RPM) . 9) Lap time . 8 11 13 12 14 10 4 5 9 6 2 3 1 7 fig. 6 14 E 10) Service indicator (fig. 6). The indicator illuminates to signal when a service is due. The service indiactor will remain on the display until the system is reset by the Ducati Service Centre who carry outthe service. 11) LAP function (fig. 6). Indicates that the LAP has been activated. 12) DDA function (fig. 6). Indicates that the Ducati Data Analyzer (DDA) has been activated. Important The instrument panel incorporates diagnostic functions for the electronic injection/ignition system. The relative menus are for the use of trained personnel only. If you accidentally access this function, turn the key to OFF and have the motorcycle checked at an authorised Ducati Service Centre. 13) Oil temperature indicator (fig. 6). Important Stop riding if the temperature reaches the maximum value, otherwise the engine might be damaged. 14) Ducati Traction Control (DTC) (fig. 6). Indicates activation of the DTC control unit (if present). 15 E LCD – How to set/display parameters At key-on (key turned from OFF to ON ) the instrument panelactivates all the digits of the LCD for 1second and switches on the indicator lights in sequence.

Incoming search terms:

AJP PR5 USER MANUAL/ OWNER'S MANUAL

0

Filed Under (Ajp) by admin on 12-12-2010

download
DIGITAL SPEEDOMETER The digital speedometer is not available for the MX and MX PRO versions. It gives information about instantaneous speed and total or trip distance travelled. Depending on the selling market, speed and distance are indicated in Kilometres or miles. If you want to switch between these units, please contact your AJP dealer. To switch from total to trip distance push button 1. To reset trip distance the trip distance must be selected; then push button 1 until the distance is reset to zero. LEFT HANDLEBAR 1 – Clutch lever The clutch lever is used for disengaging the drive to the rear wheel when starting the engine or shifting the transmission gear. Squeezing the lever disengages the clutch. 2 – Parking light on With the light knob in this position, parking lights in the headlight and taillight will be switched on. 3 – Lights off In this position, no lights will be switched on. 4 – Low beam on In this position, low beam light will be on in the headlight and presence light will be on in the taillight. 5 – High beam on In this position, high beam light will be on in the headlight and presence light will be on in the taillight. 6 – Turn sign on Turning this button left left turn lights will be on. Turning right, right turn lights will be on. To switch turn lights off, place the button in middle position. 7 – Horn To actuate horn, press this button

Incoming search terms:

YAMAHA FJR1300N OWNER'S MANUAL

0

Filed Under (Yamaha) by admin on 12-12-2010

download
3-2 3 EAU03034 Indicator and warning lights EAU04121 Turn signal indicator lights “” a n d “” The corresponding indicator light flashes when the turn signal switch is pushed to the left or right. EAU00061 Neutral indicator light ” ” This indicator light comes on when the transmission is in the neutral position. EAU00063 High beam indicator light ” ” This indicator light comes on when the high beam of the headlight is switched on. EAU03201 Oil level warning light ” ” This warning light comes on when the engine oil level is low. The electrical circuit of the warning light can be checked according to the fol- lowing procedure. 1. Set the engine stop switch to ” ” and turn the key to “ON”. 2. Shift the transmission into the neu- tral position or pull the clutch lever. 3. Push the start switch. If the warning light does not come on while push- ing the start switch, have a Yamaha dealer check the electrical circuit. NOTE: Even if the oil level is sufficient, the warning light may flicker when riding on a slope or during sudden acceleration or deceleration, but this is not a mal- function. EAU03192 Engine trouble warning light ” ” This warning light comes on or flashes when an electrical circuit monitoring the engine is defective. When this oc- curs, have the Yamaha dealer check the self-diagnosis system. The electrical circuit of the warning light can be checked according to the fol- lowing procedure. 1. Set the engine stop switch to ” “. 2. Turn the key to “ON”. If the warn- ing light does not come on, have a Yamaha dealer check the

Incoming search terms:

YAMAHA YZF-R1R/ YZF-R1RC OWNER'S MANUAL

0

Filed Under (Yamaha) by admin on 03-12-2010

download
1. Right turn signal indicator light “” 2. Fuel level warning light “” 3. Oil level warning light “” 4. Neutral indicator light “” 5. Engine trouble warning light “” 6. High beam indicator light “” 7. Left turn signal indicator light “”
INSTRUMENT AND CONTROL FUNCTIONS 3-3 3 EAU04895 Oil level warning light “” This warning light comes on when the engine oil level is low. The electrical circuit of the warning light can be checked by turning the key to “ON”. If the warning light does not come on for a few seconds, then go off, have a Yamaha dealer check the electrical cir- cuit. NOTE: Even if the oil level is sufficient, the warning light may flicker when riding on a slope or during sudden acceleration or deceleration, but this is not a malfunction. This model is also equipped with a self-diagnosis device for the oil level detection circuit. If the oil level detection circuit is defective, the following cycle will be repeated until the malfunction is corrected: The oil level warning light will flash ten times, then go off for 2.5seconds. If this occurs, have a Yamaha dealer check the motor- cycle. EAU00061 Neutral indicator light “” This indicator light comes on when the transmission is in the neutral position. EAU04896 Engine trouble warning light “” This warning light comes on or flashes when an electrical circuit monitoring the engine is defective. When this occurs, have a Yamaha dealer check the self-diagnosis system. (See page 3-7 for an explanation of the self-diagnosis device.) The electrical circuit of the warning light can be checked by turning the key to “ON”. If the warning light does not come on for a few seconds, then go off, have a Yamaha dealer check the electrical circuit. EAU00063 High beam indicator light “” This indicator light comes on when the high beam of the headlight is switched on

Incoming search terms:

Incoming search terms: