ULTIMA IGNITION MODULE AND KIT INSTALLATION MANUAL FOR HARLEY DAVIDSON

0

Filed Under (Harley Davidson) by admin on 03-03-2011

download
Disconnect battery. 2. Mark location of timing plate in relation to inside of cam cover. This will give a starting point for timing on new module. Remove old ignition if applicable (see manual) Clymer, Haynes. 3. If your bike is not equipped with timing rotor M/W# 53-528 OEM#32402-83 you must buy one (included in kit). Also a single fire coil is needed (included in kit) M/W# 53-632. Any single fire coil rated 2-4 ohms can be used. NO SOLID CORE PLUG WIRES (copper, silver) they will damage the unit. 4. Install module: helpful hints, early model nose cones, i.e. Shovel Heads, the hole for the wire may need to be drilled out. Align with previously scripted mark for timing. Use lockwashers for stand offs for correct clearance of cover plate. Run wire loom. 5. Connect wires, see wiring diagram. Tape unused wires, green or brown. 12v to tach (brown) will damage module. Set timing. 1996 and later should not be timed 20˚ BTDC as the OEM module, but at 35˚ BTDC. Use this mark when using timing light. If VOESswitch is not used you must ground VOES wire (green) while timing. Refer to manual for correct identification of timing marks. At start up and timing, set spark advance in middle position. FUNCTION SWITCHES LED timing indicator light: When out, shows TDC. When ignition is on, LED will light up. When engine is cranking LED will blink. Electric Start/Kickstart: Set accordingly. VOES/Race mode: VOES switch lets the motor run smoother and improves gas mileage. If you don’t use it or add one tape up green wire and switch to race. VOES switch to use, M/W# 53-652. Spark advance: High compression motors should use race mode and 93 octane or better gas. Changing from VOES to race changes advance curves. Agood rule of thumb is if the engine knocks when throttle is applied in high gear, turn back spark advance curve until it stops engine knock. RPMlimiter: Set at desired RPM to cut engine power. Rear Cylinder: This is for racing and should be set at a dyno. +/-5˚. Rear cylinder timing is achieved through this adjuster. Most should dial to middle setting and leave alone. After all switches are set, install cover with supplied gasket and feel the increased performance of a solid state single fire ignition. Again, we remind you, if you don’t feel confident about installing this unit, let a qualified mechanic do it and be assured you are getting the best performance and gas mileage possible.

Incoming search terms:

KTM 125/ 200/ 250/ 300 SX, MXC, EXC SERVICE MANUAL

0

Filed Under (KTM) by admin on 28-11-2010

download
Compression damping of shock absorber (MXC, EXC) The compression damping (during compression) can be adjusted for the MXC and EXC shock absorbers (Mono Compression Control). The degree of damping can be adjusted by turning adjusting screw 1 with a screwdriver. Turning in a clockwise direction will increase the damping, turning in a counterclockwise direction will decrease the damping. STANDARD ADJUSTMENT: -Turn the adjusting screw clockwise to the stop. -Then turn the adjusting screw counterclockwise, counting the number of clicks that corresponds to the respective type of shock absorber. Type White Power 1218X757…………..17 clicks Type White Power 1218X759…………..17 clicks * WARNING * THE DAMPING UNIT OF THE SHOCK ABSORBER IS FILLED WITH HIGH – COMPRESSION NITROGEN . NEVER TRY TO TAKE THE SHOCK ABSORBER APART OR TO DO ANY MAINTEN – ANCE WORK YOURSELF . SEVERE INJURIES COULD BE THE RESULT . NEVER UNSCREW THE BLACK SCREW 2 CONNECTION (24 MM ). Rebound damping of shock absorber (SX, MXC, EXC) By using the adjusting screw 3 , the degree of damping of the rebound can be adjusted. Turn the knob to the right side to increase damping, turn it to the left side to reduce damping during rebounding. STANDARD ADJUSTMENT: -Turn the adjusting screw clockwise to the stop. -Then turn the adjusting screw counterclockwise, counting the number of clicks that corresponds to the respective type of shock absorber. Type White Power 1218X756…………..28 clicks Type White Power 1218X757…………..28 clicks Type White Power 1218X759…………..26 clicks * WARNING * THE DAMPING UNIT OF THE SHOCK ABSORBER IS FILLED WITH HIGH – COMPRESSION NITROGEN . N EVERTRYTOTAKETHESHOCKABSORBERAPARTORTODOANYMAINTE – NANCE WORK YOURSELF . SEVERE INJURIES COULD BE THE RESULT . NEVER UNSCREW THE BLACK SCREW 4 CONNECTION (15 MM )

Incoming search terms:

Ducati 748 biposto specification

0

Filed Under (Ducati) by admin on 11-11-2010

download
part Number: G790-100-12A Description: Gasket Exhaust 4 Valve Belt product Details: Vee Two Gasket Sets are die cut from high quality gasket material and are supplied with ‘O’ Rings and Oil Seals. uoM: each Year from : all Year to : all part Number: V2-02-7307 Description: Main Bearing – Fits all 2 V + 4 V Belt to 2006 product Details: These bearings are carefully sourced from high end manufacturers and are supplied ro match the specific Bearing Clearances and fitting tolerances required for their particular requirements. uoM: each Year from : all Year to : all part Number: V2-03-604A Description: Camshaft – Road Drop In – Kit of 2 cams inlet only product Details: Drop in Street / Track camshaft, suited to predominately bigger bore 4 valve motors. Gives great bottom end feel due to increased torque. uoM: kit Year from : all Year to : all part Number: V2-03-606 Description: Camshaft – Track – Kit of 4 cams product Details: A predominately race bred camshaft made to produce horsepower at high revs. Very strong above 8500rpm. Must have a very high compression ratio motor, 13.5-1 minimum. uoM: kit Year from : all Year to : all

KAWASAKI STX-12F, STX-15F Riva/Vortech Supercharged STX-15F Engine INSTALLATION MANUAL

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
Our race bred Supercharger System for the Kawasaki STX-15F contains all necessary engine components to produce the ultimate 80mph closed course race craft. Kit contains the same specifications that Team Kawasaki won two 2004 Pro Runabout World Titles with. System produces over 300hp using VP MS109 race fuel (Jet X). Kit includes Vortech Supercharger & Intercooler Forged Racing Pistons, Free flow Exhaust Kit, Race programmed ECU, High volume Injectors & Fuel Pump along with all necessary hardware and detailed installation instructions. Riva/Vortech Supercharged STX-15F Engine (Team Kawi Spec) PERFORMANCE DATA Stock 61 MPH @ 7,600 RPM Supercharged 80+ MPH @ 8,300 RPM RIVA STX-15F OFFSHORE RACE KIT Our Offshore Racing Kit for the Kawasaki STX-15F contains the same components and specifications that Team Kawasaki developed to dominate the international racing circuit. This modification delivers over 200hp producing awesome acceleration and a top speed of over 700mph using VP MS109 race fuel (Jet X). Kit includes high compression racing pistons, performance intake & exhaust cam shafts, Race programmed ECU along with all necessary gaskets and detailed installation instructions

Incoming search terms:

Incoming search terms: