HARLEY DAVIDSON UNIVERSAL VISTA INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 12-03-2012

download
1. Turn Harley Davidson thumb screw control all the way off. 2. Remove screw (A) from the motorcycle throttle housing. Position the mounting bracket, as shown in drawing. Replace throttle housing screw through the hole in the foot of the mounting bracket and into the throttle housing. Loosely tighten screw. 3. Slide the cruise control’s slip ring assembly over the end of the throttle grip up to the switch housing. NOTE: Metal band on slip ring assembly is next to switch housing not set screws. Insert correct size rubber filler between slip ring assembly and grip with “joint” of filler on bottom side, midway between two set screws. Tighten all set screws into rubber filler until tight or flush. 4. Place thumb lever slot over eye bolt. Depress spring to line up holes, and insert socket head screw. 5. Insert thumb lever screw into the hole in the head of mounting bracket that keep screw parallel to grip. Install the washer then the locknut on the thumb lever screw. Tighten locknut until mounting bracket and thumb lever are snug BUT loose enough to let thumb lever move freely up and down. 6. Secularly tighten the throttle housing screw (A) in step 1. 7. Twist throttle back and forth to insure there is no binding, slip ring is “SQUARE” with switch housing and thumb lever operates smoothly between “ON” and “OFF”. 8. CRUISE CONTROL ADJUSTMENTS – Twist throttle to half position and push thumb lever down to “SET” position. Throttle should hold snugly in this position. Flipping thumb lever to “OFF” position, releases cruise control hold, throttle should return to “OFF” position. Tightening acorn nut (B) will increase cruise control hold. Loosening acorn nut will decrease cruise control hold. Always check to make sure that throttle can be rotated both ways in “SET” position after adjustments.

Incoming search terms:

STREET TUNNEL RAM INTAKE MANIFOLD INSTALLATION INSTRUCTIONS

0

Filed Under (Tips and Review) by admin on 07-02-2011

download
PREP AND TUNING FOR POWER: 1. Specific applications may show an increase in performance through additional carburetor tuning. 2. Aftermarket distributor curve kits and aftermarket ignitions may be used with the Street Tunnel Ram intake manifold. 3. Use modified or high performance cylinder heads such as our Performer RPM, and port match the intake manifold to the heads. 3. The engine’s compression ratio should be at least 9.5:1 to work properly with Torker-Plus or Performer RPM camshafts. INSTALLATION PROCEDURE INTAKE MANIFOLD BASE 1. Use only recommended intake gaskets set when installing this intake manifold. 2. Fully clean the cylinder head intake flanges and the engine block end seal surfaces. 3. Apply Edelbrock Gasgacinch sealant P/N 9300 to both cylinder head flanges and to the cylinder head side of the gaskets, allow to air dry, and attach the intake gaskets. 4. Do not use cork or rubber end seals. Use RTV silicone sealer instead. Apply a ΒΌ” high bead across each block end seal surface, overlapping the intake gasket at the four corners. This method will eliminate end seal slippage. 5. Install the intake manifold hold-down bolts (We offer an Intake Manifold Bolt Kit #8504 that includes small-head silver Cadmium-plated bolts and matching hardened washers). Apply a small amount of RTV silicone to the threads of the eight inner bolts (1,2,3,4,5,7,9, & 11) (See Figure 1) . This will prevent oil weepage, as generally these are not blind holes in the cylinder head. 6. Torque all of the manifold bolts in two steps by the sequence shown in Figure 1 to 25 ft/lbs. INTAKE MANIFOLD TOP 1. Apply Edelbrock Gasgacinch sealant P/N 9300 to the gasket mating surface and install the gasket and manifold top. 2. Install and tighten the supplied hold down bolts using a liquid thread-locking compound on the bolt threads. As an extra safety precaution, we suggest you drill a small safety wire hole in the head of each bolt and safety wire them together. Edelbrock Corporation expressly disclaims any liability for any and all consequential damages

Incoming search terms:

Incoming search terms: