HARLEY DAVIDSON CONTOURED TOUR-PAK LUGGAGE RACK KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 05-04-2011

download
INSTALLATION NOTE The location of the Tour-Pak spoiler has a direct relationship to the location of Tour-Pak mounted luggage rack. The spoiler template will locate the Tour-Pak spoiler in the correct position for the luggage rack so that the spoiler may be added in the future. It is recommended that the spoiler be installed first. See Figure 1. 1. Identify if the installation of a Tour-Pak mounted spoiler is desired in the future. Use the template if the spoiler will be installed. Cut the template along the appropriate line. Carefully place template on top of Tour-Pak lid, aligning edges of template with top surface of Tour-Pak. Tape template in desired location. 1 is 00579 1. Check clearance between rack and spoiler Figure 1. Tour-Pak Rack and Spoiler NOTE Position top rack with upright section toward rear of motorcycle. To avoid contact with the passenger backrest pad, do not mount the top rack in too far forward a position. 2. See Figure 2. Place the four mounting pads (1) onto the four mounting supports on top rack (2). Carefully center the rack on the lid and position the rack rear supports 5/8 inch to 3/4 inch (16 mm to 19 mm) in front of the emblem on the Tour-Pak lid, as shown. 1 is 00636 1.5/8 in. – 3/4 in. (16 mm – 19 mm) Figure 2. Locate Holes From Emblem 3. Use a grease pencil to temporarily mark the positions of the four mounting pads on Tour-Pak cover. NOTE Apply masking tape to the Tour-Pak cover painted surface at the four points where the top rack mounting holes will be drilled. The tape can be marked for hole location, and will help prevent the paint from being chipped during the drilling procedure. 4. Carefully remove top rack/mounting pad assembly. Place a strip of masking tape over each grease pencil mark on the Tour-Pak cover. Once again, position top rack/mounting pad assembly on Tour-Pak cover in the desired mounting location. 5. Using a soft lead pencil on the masking tape strips, trace a circle around each mounting pad. Remove top rack/mounting pad assembly. Use a ruler to mark the exact center of each circle drawn on the tape strips. NOTE Remove all contents from within the Tour-Pak to avoid possible contact with the moving drill bit during the following drilling procedure. 6. Drill starter holes using a 1/16 inch drill bit. Drill the finished holes for the mounting screws using a 9/32 inch drill bit. Remove masking tape strips. 7. Apply a small amount of silicone sealant around each mounting hole on interior surface of Tour-Pak cover

Incoming search terms:

HARLEY DAVIDSON FAIRING MOUNT MIRRORS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 20-02-2011

download
INSTALLATION Removing Outer Fairing 1. Standing at the front of the vehicle, use a T-27 TORX® drive head to remove the three outer fairing screws (with flat washers) just below the windshield. 2. Moving to the inner fairing side, use a T-27 TORX drive head to remove the two fairing screws just above the wind deflectors on the left and right side. 3. Turn the handlebar to the right and remove the outer fairing screw (reach in below the fairing cap). Turn the handlebar to the left and remove the fairing screw on the opposite side. 4. Tilting the outer fairing toward the front, squeeze the two external tabs to remove the wire connector at the back of the headlamp assembly. 5. Lift the fairing (with headlamp assembly) off the motor- cycle. NOTE Since the outer fairing screws hold the windshield in place, the windshield may fall to the floor if not removed. 6. Remove the Windshield. Installing Mirrors 1. See Figure 1. Place template on inside of fairing as shown to locate mounting holes for mirror. 2. Begin by drilling a 1/8 inch pilot hole at each location marked on the template. For the center hole (2) where the 3/8 inch threaded stud passes through the fairing use a 13/32 inch diameter twist drill to drill the hole to its final size. For the alignment hole (1), use a 7/32 inch diameter twist drill to drill the hole to the final size. 2 1 is 02115 1.7/32 inch hole location 2.13/32 inch hole location Figure 1. Positioning Template 1 is06315 1. Auxiliary mirror Figure 2. Orientation of Auxiliary Mirror NOTE The flange nut is a self locking nut and must not be tightened more than 30 in-lbs (3.4 Nm). 3. See Figure 3. Place mirror (2) in position and install backing plate (4) with the raised post (B) (with the L and R marking) toward the nut surface. Install the flange nut (6) and tighten nut to 20-30 in-lbs (2.3-3.4 Nm). 4. See Figure 2. Position the mirror so the round auxiliary mirror is in the upper inside corner position. 5. Repeat for right side

Harley-Davidson FLH Accent Panel Installation Manual

0

Filed Under (Harley Davidson) by admin on 16-02-2011

download
1 Install Accent Panels Note: See hardware list on Page 4 for usage and descriptions. 1.1 Elevate the rear of the vehicle and support with jack stands under the rear differential tubes. 1.2 Remove the rear wheels 1.3 Remove the passenger foot rests. 1.4 Remove front fairing (for wiring later in installation) . 1.5 Install cross brace and frame clamps to frame in the approximate position shown in Figure 1. 1.6 Note orientation of cross brace (Figure 2). Flat side of the brace against bottom of frame tubes. Outboard tabs up and to the rear of the vehicle. 1.7 Leave the bolts loose to allow the bracket’s position to be adjusted later in installation. 1.8 Install front brackets to vehicle between the frame and crash bars as shown, using the supplied hardware (the left side bracket is longer than the right. Figure 3 1.9 Leave the bolts loose to allow the bracket’s position to be adjusted later in installation. 1.10 Position the accent panel to vehicle. Figure 4 1.11 Install supplied hardware to front and cross brackets. Figure 5 &Figure 6 1.12 Leave the bolts loose to allow the accent panel’s position to be adjusted later in installation. 1.13 If not already preinstalled to your accent panel, install rubber bead edge molding between trike body (fender) and accent panel. Bead edge molding 1.14 Clamp the accent panel to the body (fender). Check position of accent panel and ensure proper positioning of bead edge molding. 1.15 Four holes will be drilled though body (fender) and accent panel in the approximate positions shown (both left and right accent panels). Figure 8 Note: Hole location dimension in Figure 8 are approximations. Your drill location may and can vary. Note: Hole position should be as high an possible on the accent panel, allowing space to install hardware 1.16 With accent panel and bead edge molding properly positioned and clamped to body (fender), Drill the two outboard holes in the approximate position shown from inside the fender well through mounting surface of accent panel. Note: Drill outboard hole first and install hardware to reduce risk of accidental movement. Figure 9 1.17 Drill remaining two inboard holes from the accent panel mounting surface through the body (fender). Figure 10 1.18 With both left and right accent panels installed, tighten all hardware at the left and right front mounting positions. 1.19 Trim off excess bead edge molding. 1.20 With left and right front mounting secure, check position and alignment of cross bar and accent panel mid mounts and tighten all hardware. 1.21 With fairing removed, crimp supplied xxx to the black, purple and blues wires of the vehicle’s turn signal wire loom. 1.22 Crimp one of the supplied male spade connectors to the end each wire from the accent panel. 1.23 Connect wiring as indicated in Table 1 below. Accent Panel Wire Color Vehicle Turn Signal Loom Wire Color Yellow Purple (Signal) Orange Blue (Running) Black Black (Ground) Table 1

Incoming search terms:

HARLEY DAVIDSON SOFTAIL SEAT KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 13-02-2011

download
INSTALLATION FXST, FXSTS, and FXSTB models NOTE When performing the following installation procedures, avoid scratching painted surfaces (fender, tank, etc.) with tools or metal seat tabs. 1. Remove existing seat from motorcycle by unscrewing seat at rear bracket and unhooking front seat tab. 2. See Figure 4. Remove and discard existing grabstrap and save fastening hardware from the motorcycle. 3. See Figure 4. Install the grabstrap (7) from kit with the hardware saved in Step 2. Install the grabstrap according to Figure 1. Kit Number: 51470-06A, 51397-06A Grabstrap Number: 51184-00 Kit Number: 51468-06A, 51469-06A, and 51801-07 Grabstrap Number: 51176-96B is00420 Figure 1. Grabstrap installment information 4. See Figure 4. Slide the back of the seat through grabstrap and hook front tab of seat (1) into frame. Secure seat bracket to fender with screw (8). After installing seat, pull upward on seat to be sure it is locked in position. While riding, a loose seat can shift causing loss of control, which could result in death or serious injury. (00070b) 2007 and later FXSTC models NOTE Refer to the Owner’s, or Service Manual instructions for removal of the stock seat, and mounting hardware. 1. Remove, and discard the existing grabstrap, and mounting hardware. 2. Remove, and discard the plug in the rear mounting position on the fender. 3. See Figure 2. Using the retaining nut (1), washer (2), and cable strap from the kit; Install the nut, and washer in the rear hole location on the fender (Note: A cable strap can be used as an installation aid)

HARLEY DAVIDSON TOUR-PAK KIT INTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 07-02-2011

download
INSTALLATION 1. Remove the rubber mat from the bottom of the Tour-Pak. 2. See Figure 1 and Table 1 to determine the proper hole configuration to attach the Tour-Pak to your luggage rack. Holes will be drilled as explained in Step 3 in the hole location for your luggage rack. Table 1. Luggage Rack and Hole Configurations Hole Configura- tion Luggage Rack C (3 holes) Stock 1997 B (4 holes) Detachable luggage rack 53107-96 A (5 holes) Luggage rack 53118-97A and luggage rack 53118-98 A (5 holes) Stock 1998 and later racks A (5 holes) Detachable Tour-Pak rack 53276-04 B (4 holes) Solo detachable Tour-Pak rack 53655-04 B (4 holes) Detachable Tour-Pak rack 53066-00B B (4 holes) Solo detachable Tour-Pak rack 53559-04A A (5 holes) Solo detachable Tour-Pak rack 53260-02 -J03631 1 of 3 B 1 A C 2 2 2 is00163 1. Front of motorcycle 2. Bottom view of Tour-Pak interior (rubber mat removed) Figure 1. Hole configurations for Tour-Pak attachment NOTE Drilling holes in Tour-Pak without wood underneath each hole site may result in the leather becoming damaged during the drilling process. 3. Place blocks of wood underneath the Tour-Pak where the holes will be drilled to prevent damage to the leather while drilling. Use the pre-drilled holes in the metal base as a guide and carefully drill the holes through the leather in the proper location using a 11/32 inch drill bit. 4. See Figure 2. For detachable luggage racks (53107- 96, 53066-00B and 53276-04): Install black cover tube to the front bar (1) of the luggage rack, as shown. This tube is used to provide a cleaner look. The black cover tube is not for use with other luggage racks. 5. Attach Tour-Pak to rack using the mounting screws provided in the Luggage Rack kit. Put bolt through from inside of Tour-Pak. Tighten screws to specifications found in the Luggage Rack kit. 6. Place the black rubber mat on the bottom of the Tour-Pak. 7. If luggage rack was removed, reattach to motorcycle according to kit instructions or Service Manual instructions

HARLEY DAVIDSON XL SEAT KITS REMOVAL AND INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 29-01-2011

download
1 2 is 00911 1. Tongue 2. Keyhole Figure 2. Underside of 2-up seat INSTALLATION NOTE If installing the seat with a sissybar/backrest pad present, remove the backrest pad prior to seat installation. This will prevent damage to the pad and/or seat. Reinstall backrest pad after the seat is installed. 1. Models equipped with solo seats: See Figure 1. a. Remove the plastic plug (1) from the rear hole location in the fender (2). Save the plastic plug for installation. b. Move the seat retention nut (4) and lockwasher (5) from the middle location to the rear location, where the plug was just removed. As shown in the inset, a cable strap (6) can be used as an installation aid. Place the retention nut (5) over the cable strap so that the wide end of the nut rests on the eye of the cable strap. Thread the cable strap up under the fender, and through the fender hole. Pull up on the cable strap to hold the nut snug against the underside of the fender. c. With the rib of the retention nut (4) seated into the notch in the fender hole, slide the retension washer (5) into place from the rear. This will lock the retention nut in place. d. Reinstall the plastic plug in the fender hole in the middle location. NOTE The foam cushioning of the seat needs to be compressed as the seat is slid forward to engage the post on the frame when the seat is dropped into place. When properly installed, the front tongue on the underside of the seat should fit snugly in the groove at the fuel tank rear mounting location and the keyhole on the underside of the seat will lock the seat to the post on the frame. 2. All models: See Figure 2. a. Angle the front of the new seat into place so the tongue (1) engages the slot at the rear fuel tank mounting location. b. Push the seat forward and rotate the rear of the seat downward until the seat contacts the frame. Flex the seat slightly in the middle and slide the seat towards the rear so that the keyhole slot (2) on the seat bottom engages with the center seat post on the frame. 3. See Figure 3. Pull up on the center of the seat to verify that it is locked into place. (There will be a small amount of play, but the seat should only come up about a half an inch and then will be held firmly in place by the post on the underside of the seat.) If the seat is not firmly in place, repeat Step 2 until the seat is firmly in place. Reference the Owners Manual for further instruction on seat placement if needed

Incoming search terms:

Incoming search terms: