harley- davidson DYNA BLACK FORWARD CONTROL KIT installation Manual

0

Filed Under (Harley Davidson) by admin on 15-03-2012

download
1. Disconnect battery cable, negative (-) cable first. 2. Remove the left side rider footrest assembly. Save the footrest and fasteners for installation. Discard the remaining hardware. 3. From the kit, press hole plugs (8) into the screw holes on the frame where the stock footrest assembly was mounted. 4. Remove plugs from forward control frame mount (I) and discard. 5. Remove the foot shifter lever (A) and shifter peg (D). Discard the old foot shifter lever (A). Save the foot shifter lever hardware and shifter peg (D) for future use. 6. See Figure 2. Remove the primary chaincase cover (6) and primary chaincase housing (1). Refer to your model motorcycles Service Manual for removal procedures. NOTE See Figure 1. Before removing the gear shifter lever (1) ((H) in Table 1), it is necessary to mark the correct orientation of the lever. Using a marking tool, draw a location marking (4) on the end of the splined shaft (2) across from the casting split (3). This will allow the new gear shifter lever to be installed in the same orientation as the old lever. 5 3 4 1 2 is 02083 1. Gear shifter lever 2. Splined shaft 3. Casting split 4. Location marking 5. Lever bolt Figure 1. Gear Shifter Lever Orientation 7. After marking the gear shifter lever orientation, loosen the lever bolt (5) and remove the old shifter lever. Discard the old gear shifter lever but keep the lever bolt. From the kit, install the new gear shifter lever onto the splined shaft in the same orientation as the old shifter lever. Tighten the lever bolt to 18-22 ft-lbs (24.4-29.8 Nm)

HARLEY DAVIDSON XL CHROME FORWARD CONTROL KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 09-03-2011

download
2008-05-05 XL CHROME FORWARD CONTROL KIT GENERAL Kit Number 33395-04, 33398-04 Models For model fitment information, please see the P&A Retail Catalog or the Parts and Accessories section of www.harley- davidson.com (English only). Additional Parts Required The rider’s safety depends upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333a) NOTE This instruction sheet references Service Manual information. A Service Manual for your model motorcycle is required for this installation and is available from a Harley-Davidson Dealer. Kit Contents See Figure 5, Figure 6 and Table 1. INSTALLATION Remove Stock Shift Lever and Footrest Assembly 1. See Figure 1. Loosen the shift lever retaining screw (2) securing the shift lever (1) to the shifter shaft. Slide the shift lever off the splined shaft. Remove shifter peg from lever and save for installation. Discard shift lever. 2. Remove the two socket head screws (4) securing the footrest bracket (3) to the frame and remove footrest. Discard screws. 3. See Figure 5. Obtain two hole plugs (1) from kit and firmly press plugs into frame screw holes remaining from footrest removal. 4. See Figure 2. Remove the retaining ring (1) from the clevis to free the footrest clevis pin (4). Remove the clevis pin and footrest (3) from the footrest support. Save footrest for installation. Discard retaining ring, clevis pin, spring washer and footrest bracket. 1 2 4 3 is 01887 1. Shift lever 2. Retaining screw 3. Footrest bracket 4. Socket head screw Figure 1. Remove Shift Lever and Footrest 5 1 3 2 4 is 01901 1. Retaining ring 2. Spring washer 3. Footrest 4. Clevis pin 5. Footrest bracket Figure 2. Remove Left Footrest from Support Remove Stock Brake Pedal and Footrest Assembly 1. See Figure 3. At the right footrest, remove the retaining ring (1) clevis pin (2), footrest (3) and spring washer (4). Discard all hardware but save footrest for installation. 2. Remove brake rod (5) from brake pedal and master cylinder bell crank. Discard brake rod. 3. Remove the two screws (6) and right footrest/brake pedal support bracket with attached brake assembly from frame

HARLEY DAVIDSON CHROME INNER PRIMARY COVERS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 23-02-2011

download
INSTALLATION 1 2 3 is06139 Figure 1. Remove Three Original Equipment Screws As Shown 1. See Figure 1. Remove the stock fasteners as shown in Figure 1. Save screw (3) for reuse. 2. Install the stock fastener in the rear inner cover. Place a locating washer over the fastener with the rounded side facing toward the hole in the primary chain case. 3. Slide the rear inner cover into place and loosely secure it with the stock fastener. 1 is06416 1. Acorn nut Figure 2. Fasten Front And Rear Inner Primary Covers Together 4. See Figure 2. Position the front inner cover over the rear inner cover and make sure that the hole in the front cover fits over the threaded stud in the rear cover. Secure the covers together with the acorn nut installed finger tight. 5. See Figure 3 and Table 1. Place the new 4.25 inch (5) and 1-1/2 inch (4) screws in the front inner primary cover. Place locating washers (6) over the fasteners with the rounded side of the washer facing toward the hole in the primary chain case. 6. Tighten all three screws to 108-120 in-lbs (12.2-13.6 Nm) . 7. Tighten the acorn nut. 8. Push the Allen hole plugs (7) into the four exposed screw heads

HARLEY DAVIDSON ADJUSTABLE AIR DEFLECTOR KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 15-02-2011

download
INSTALLATION 1. See Figure 1. Models with NO air deflectors installed: Remove and discard the eight hole plugs (1) from the right and left edges of the inner fairing assembly. Models WITH air deflectors currently installed: Remove and discard the eight screws that retain the right and left air deflectors. Remove and discard the deflectors. 2. See Figure 2. Select a right-side (1) or left-side (2) air deflector, and four screws (3) from the kit. Determine the correct side by holding the mounting-hole side of the deflector against the fairing. 3. Place the deflector against the inner fairing, lining up the holes. Insert the screws through the deflector holes and into the fairing air deflector holes. Tighten the screws to 25-30 in-lbs (2.8-3.4 Nm) . 1 1 is04653a Figure 1. Remove Hole Plugs SERVICE PARTS 3 2 1 is04654 Figure 2. Service Parts: Adjustable Air Deflector Kit Table 1. Service Parts Table Part Number Description (Quantity) Item 58128-08A Air deflector, adjustable (right side) – Dark Smoke 1 57655-08A Air deflector, adjustable (right side) – Light Smoke 58129-08A Air deflector, adjustable (left side) – Dark Smoke 2 57657-08A Air deflector, adjustable (left side) – Light Smoke 2563 Screw (8

HARLEY DAVIDSON SPORTSTER FORWARD CONTROL KITS REMOVAL AND INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 07-02-2011

download
Remove Stock Shift Lever and Footrest Assembly 1. See Figure 1. Loosen the shift lever retaining screw (2) securing the shift lever (1) to the shifter shaft. Slide the shift lever off the splined shaft. Remove shifter peg from lever and save for installation. Discard shift lever. 2. Remove the two socket head screws (4) securing the footrest bracket (3) to the frame and remove footrest. Discard screws. 3. See Figure 6. Obtain two hole plugs (1) from kit and firmly press plugs into frame screw holes remaining from footrest removal. 4. See Figure 2. Remove the retaining ring (1) from the clevis to free the footrest clevis pin (4). Remove the clevis pin and footrest (3) from the footrest support. Save footrest for installation. Discard retaining ring, clevis pin, spring washer and footrest bracket. 1 2 4 3 is03193 1. Shift lever 2. Retaining screw 3. Footrest bracket 4. Socket head screw (2) Figure 1. Remove Shift Lever and Footrest 5 1 3 2 4 is03194 1. Retaining ring 2. Spring washer 3. Footrest 4. Clevis pin 5. Footrest bracket Figure 2. Remove Left Footrest from Support Remove Stock Brake Pedal and Footrest Assembly 1. See Figure 3. At the right footrest, remove the retaining ring (1) clevis pin (2), footrest (3) and spring washer (4). Discard all hardware but save footrest for installation. 2. Remove the exhaust to access the brake rod. Follow the instructions in the appropriate Service Manual. 3. Remove brake rod (5) from brake pedal and master cylinder bell crank. Discard brake rod INSTALLATION Install Forward Control Brake Pedal and Footrest Assemblies 1. See Figure 5 and Figure 6. At the lower front of the right frame downtube, remove the two screws securing the J- clip (B) to the frame. Discard the screws but save J-clip for installation. 2. Install the other end of the brake rod into the brake pedal assembly (8). Tighten to 84-144 in-lbs (9.5-16.3 Nm) . NOTE Assemble the brake pedal and footpeg clevis onto the footrest support bracket (as described in the next step) prior to mounting the support bracket to the frame. This will allow easier installation of the footrest mount clevis retaining ring (installed to grooved end of footrest mount clevis). 3. Slide the brake pedal (8) onto footrest mount clevis (11) then slide clevis into footrest/brake pedal support bracket (9). Align hole in the clevis with hole in the support bracket and install screw (6). Tighten the screw to 18-22 ft-lbs (24.4-29.9 Nm) . 4. Install the footrest mount clevis retaining ring (18) to the groove at the end of the footpeg clevis. 5. Position the J-clip (from Step 1) against the frame aligning the mounting holes. Mount the footrest/brake pedal support bracket (9) and J-clip to frame using the new screws (3). Tighten the bracket to 45-50 ft-lbs (61.1- 67.9 Nm) . 6. Obtain the brake rod (15) from kit and thread one end into the master cylinder bell crank. Tighten to 120-180 in-lbs (13.6-20.3 Nm) . 7. Install footpeg on clevis with spring washer (2). Make sure spring washer is positioned inside clevis (11) with the square edge toward the inside. Align holes and push clevis pin (7) from top down through hole in clevis. Secure clevis pin using the new retaining ring (17). 8. Install exhaust following the instructions in the appropriate Service Manual. Install Forward Control Shift Lever Assembly

Incoming search terms: