Honda Shadow Backrest Kit Installation Manual

0

Filed Under (Honda) by admin on 07-12-2011

download
Install the right and left brackets, leave screws loose to allow brackets some movement for ease of backrest installation. Install the ackrest as shown, if optional carrier is also purchased, use the longer flange bolts provided. Note the backrest goes inside of the brackets, and carrier rack (optional) will go outside of the brackets when installed. Tighten all nuts and bolts to the torques specified

HONDA XR 250 1996 Dual Sport Kit Installation Manual

0

Filed Under (Honda) by admin on 06-12-2011

download
Get a degree in Mechanical and Electrical Engineering. (Just kidding!) 2. Remove the seat, side panels, radiator shrouds, and gas tank.
If you are color blind or even think you might be a little color blind, now is the time to get someone to assist you. Successful installation of the kit requires good color recognition. You want to go riding this weekend, don’t you? 3. Unplug the green and blue taillight wires from the stock wiring harness, remove the taillight lens, and remove the taillight socket and wiring. 4. Unplug the headlight from the stock wiring harness and remove. 5. Remove the kill switch. Unplug the black/white wire and the black wire from the connector near the base of the odometer. AC Regulator Unplug taillight here Photo 1 6. Locate the AC voltage regulator found mounted on the front top edge of the airbox as shown in Photo 1. Unplug the regulator from the wiring harness and remove regulator (Leave the U-bolt
attached to the airbox and save the bolt for a later step)

HONDA CB 90O C CYLINDER HEAD PISTON REMOVAL and INSTALLATION

0

Filed Under (Honda) by admin on 05-12-2011

download
108 CYLINDER/PISTON PISTON/PISTON RING INSPEC- TION I Inspect the piston ring-to-groove clearance. NOTE Mark the rings so that they can be returned to their original locations. Inspect the pistons for damage and cracks; ring grooves for wear. Insert each piston ring into the cylinder, and inspect the end gap

Incoming search terms:

2007-2008 HONDA CBR 600RR DUAL CANISTER SLIP- ON INSTALLATION

0

Filed Under (Honda) by admin on 04-12-2011

download
INSURE THE EXHAUST SYSTEM AND EXHAUST COMPONENTS ARE FULLY COOLED. 2. INSURE THE MOTORCYCLE IS STABLE ON KICKSTAND OR REAR CENTERSTAND OR SERVICE TABLE. 3. REMOVE BOTH THE FRONT AND REAR SEATS. 4. REMOVE THE 4 BOLTS HOLDING THE TAIL
FAIRING TO THE SUBFRAME AND REMOVE THE TAIL FAIRING. REMOVE 5. REMOVE TRIM PLASTIC JUST ABOVE RIGHT SIDE FOOTPEG. (REMOVE THE ONE BOLT AND UNCLIP) TRIM PLASTIC UNCLIP REMOVE 6. REMOVE LOWER FOOT PEG BRACKET AND REMOVE THE HEAT SHIELD BOLT. ALLOW THE FOOT PEG BRACKET TO HANG BY THE HOSE AND WIRES

Honda V4 Cam-Chain Tensioner Installation and Removal

0

Filed Under (Honda) by admin on 03-12-2011

download
Stay Organized – Misplaced and mismatched screws can be an expensive nightmare on many levels. Spend a couple bucks on organizing bins of various sizes and keep your uninstalled parts together in a logical sequence. 10 seconds now will save you 10 hours later. • Two wire coat hangers • Full metric socket Set w/ medium and long extensions • Various sizes of flat-head screwdrivers
• Safety wire (optional) • Sharpie pen (optional) • Plenty of towels and rags to wipe hands and surfaces • An extra set of hands
2) Keep records – If a job is complicated it’s easy to get confused with what went where before you took it apart. If you have a small digital camera handy and are unsure about your mechanical skills, snap pictures along the way to record how things looked. 3) Don’t get frustrated – If you start feeling frustrated and let yourself continue, you’ll probably cause more problems and damage than you’ll solve or fix. Take a break

Honda CRF230 And CRF150 Enduro Lighting Kit Installation

0

Filed Under (Honda) by admin on 02-12-2011

download
Control Switch Installation: Install the high/low/off switch on the left handlebar next to the grip. Do not tighten the screws too tight as the threads in the body of the switch can be stripped out. Zip-tie the switch wiring down along the bottom of the handlebar and over the front of the top triple-clamp. Wiring Harness Installation: Attach the plastic connector from the switch to its corresponding mate from the provided wiring harness. Route the harness back along the left side of the bike following the stock wiring harness to the area on top of the airbox. Make sure the key is in the off position before making these wiring connections. -Run the black wire with the ring terminal and the fused lead with the ring terminal down to the battery.

1994-1998 HONDA RVF400RR Racing Kit INSTALLATION

0

Filed Under (Honda) by admin on 01-12-2011

download
(1)Fuel High Octane white gasoline (2)Engine Oil Recommended Oil: HONDA Ultra-GP (for four-cycle Motorbike) SAE20W-50 or 10W-40
Full Capacity: 3.0Liter (5.28pt) Oil Exchange: 2.5Liter (4.4pt) Filter Exchange: 2.4Liter (4.224pt) (3)Spark Plug NGK R 847-10(11)(4)Cooling Water Highly recommend checking the water level on each ignition/riding. Ingredient: Tapped water or Drinking water I. Unscrew a radiator cap. Apply water up to limb of intake. II. Hold steering and heave the body two or three times to let air out. III.Add water if necessary. IV. Screw the cap tighten.V. Start Engine then check water level again. Add water if necessary. < Notes for racing condition> • Keep your attention when you re-check the water level since the water would spill out of intake. Also cover the body with wastes. • Drain cooling water in a catch-tank before riding. • Drain whole water in a radiator after riding. It avoids corrosion or clog of components. • It is admitted adding coolant in winter season. Handle carefully when you apply them. It makes the circuit slippery if it drops or spilled.

Incoming search terms:

2007 CBR1000RR REPSOL EDITION INSTALLASTION AND REOVAL INSTRUCTIONS

0

Filed Under (Honda) by admin on 30-11-2011

download
Follow the complete sequence of steps as shown. Do not short-cut any steps. The sequence has been established to ensure the unit is properly assembled. The individual steps are composed of three components: • Sub-heading—The large sub-headings are a brief description of the step. They are intended to be used by the experienced technician, one who only needs a brief reminder of the
set-up sequence. • Descriptive text—The descriptive text explains in detail what is to be done during that step. This explanation is intended as a guide for the technician needing additional information. • Photographs/Line art—The photographs or line art support both the sub-headings and the detailed text. Modifications and Accessories Modifications that you may have made, or should make in the future, to any Honda product, shall be deemed by our company to have been performed at your sole risk and responsibility, and
without our company’s or the manufacturer’s approval, or consent, implied or expressed. We further disclaim any and all liability, obligation, or responsibility for any defects of modified parts or of the modified product, and for any claims, demands, or causes of action for damage to property or for personal injuries resulting from the modification of said Honda produc

2006-2007 Honda TRX450R SR4 4 Stroke racing system INSTALLATION

0

Filed Under (Honda) by admin on 30-11-2011

download
Install Motoworks header pipe using stock nuts, finger tight at this point ( Fig 4) 2. Install Motoworks tailpipe with muffler using bolt and spacer supplied in kit on upper rear mount, use stock nut and bolt on lower mount finger tight at this point. (Fig 5 and 6) 3. Torque header pipe nuts to 1.0 kg-m ( 7.3 lb-ft ) 4. Torque tailpipe mounting bolts to 2.5 kg-m ( 18 lb-ft ) 5. Re-check all your work 6. We recommend that you clean the entire exhaust system with a mild detergent, i.e. glass cleaner prior to starting as any oily residue may cause permanent stainingBefore operating check for proper clearance between Motoworks exhaust and ATV i.e. frame, plastic, brake line, fuel line etc if problems exist re-check work

HONDA CB25O NIGHT HAWK OWNER’S MANUAL

0

Filed Under (Honda) by admin on 29-11-2011

download
The motorcycle presents you a challenge to master the machine, a challenge to adventure. You ride through the w1nd_, linked to the road by a vehicle that responds to your commands as no other does. Unlike an automobile, there is no metal cage around you. Like an airplane, a pre-ride inspection and regular maintenance are essential to your safety. Your reward 1S freedom. To meet the challenges safely, and to enjoy the adventure fully, you should become thoroughly familiar with thls owner s manual BEFORE YOU RIDE THE
MOTORCYCLE. When service is required, rememher that your Honda dealer knows your motorcycle best. If _you have the required mechanical know-how and tools, your dealer can supply you with an official Honda Service Manual to help you perform many mamtenance and repair