Honda GL1500 Gold Wing Motorcycles Trike Conversion Installation Guide

0

Filed Under (Honda) by admin on 19-12-2011

download
Secure and raise motorcycle 9 to 10 inches using a quality motorcycle lift. Remove the following from the vehicle. See OEM manual for detailed instructions. Items to be retained for reinstallation after modification are noted. • Left and right side-covers (to be re-installed with minor modification). • Seat (to be re-installed without modification). • Trunk. • Left and right passenger foot rests (to be re-installed without modification). • Left and right side-covers above passenger foot rests. • Battery and holder (to be re-installed without modification). • Left and right saddle bags (retain side cover mounting grommets for re-use). • Left and right mufflers. • Rear wheel. • Rear brake line to master cylinder.** • Reverse resistor assembly (to be relocated). • Swing Arm (Drive shaft boot will not be used). • Bank angle sensor. • Shocks. Air shock (non coil-over) to be reused. ** Thoroughly vacuum drain rear brake system, including feed line to left front caliper Modification to Trunk / Luggage Stay Removal from vehicle frame is not necessary. a. Cut the down tubes of the trunk stay and remove the lower section as shown in Figures 1 & 2 b. Trim rear upper tube-end rounded corners just outboard of welded nut. Trim line should be parallel with center line of vehicle. This will provide clearance for body when installed. Figure 2 (Inset) c. Remove the Hazard and Turn Signal relays from the center holder; bend Relay Holder Tab up 90°. Relays will be relocated to left and right sides. Figure 3

Balancing Honda GL1500 Carburetor Manual

0

Filed Under (Honda) by admin on 08-04-2011

download
First pry off the plastic clip covering the screw as in the first picture. Note the type of screw used, as shown in the third picture. You must put this one back in the right place. Tip; When refitting this clip later on, a bit of Blutack or similar will stop it falling off and getting lost. Pull the L piece trim away, taking care not to break the tab shown in the fifth picture Now pry off the small black plastic cover at the rear of the running light. Blutack will be a good idea here as well when refitting the cover. The owner of this GL1500 didn’t use it and the cover on each side of the Goldwing got lost, which is why you can’t see them in the pictures. Note the type of screw used here as well, same as the one mentioned earlier. The third picture shows the two normal Phillips screws at the front of the running light, remove them. Remove the running light and pull the lower fairing panel away Remove the rubber plug from the right side fan. The adjuster screw for balancing the carbs is about 6″ behind and up, and hard to see. I removed the fan so I could get the camera in and the second picture shows the adjuster screw

Incoming search terms:

HONDA GL1500 Radio Knobs Installation Manual

0

Filed Under (Honda) by admin on 28-02-2011

download
NOTE: Read instructions carefully before installing. 1. Place bike on center stand. Remove the 5 original knobs. 2. Using needle nose pliers, remove the knob stops from the 2 left hand knob sockets. 3. Install replacement chrome knobs. ® Installation Instructions For Part 15673-235 GL1500 Radio Knobs

HONDA GL1500 Chrome Key Cover INSTALLATION MANUAL

0

Filed Under (Honda) by admin on 28-02-2011

download
1. Place bike on center stand. 2. Remove the OEM key cover by pressing down and turning counter clock wise. 3. Put a little lubricant on the tabs of the new part. 4. Install chrome cover and turn clock wise to secure

HONDA GL1500 FRONT WHEEL INSTALLATION MANUAL

0

Filed Under (Honda) by admin on 27-02-2011

download
1. Rotor Covers. Tri-chromed ABS rotor covers replace the painted ones. Light weight, beautiful and functional. Include a rear strap and sold in pairs. Also, available are chrome rotor covers with amber strip lights installed. Fits 1988 to 2000. 2. Fork Light Mounts . Specially designed mounts are tri-chromed metal and hold a total of 6 lights. Lights not included. Sold in pairs 3. LED Lighted Rotor Cover Trim Rings . NEW Update your bike with LED lights. Tri-chromed ABS rings include amber or red, blue and amber LED lights. Sold in Pairs 5. 252-216 Rotor cover Plugs. These¾” chromed steel plugs fill the holes on the GL1500 rotor covers. Sold in a 4 pack