HARLEY DAVIDSON SADDLEBAG LID COVER KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 15-02-2011

download
INSTALLATION NOTE To avoid failure, the fastening tab adhesive must be allowed to cure for 24 hours before installing these Lid Covers. NOTE Lid Cover installation may be easier with the saddlebags removed from the motorcycle. 1. See Figure 1. Open the saddlebag lid. Remove the two T-20 TORX® screws (5) attaching the check strap (3) to the lid. 2 4 2 3 1 6 7 4 4 6 5 is02962 1. Saddlebag lid cover 2. Hook and loop fastener, 1.5 inch 3. Check strap 4. Hook and loop fastener, 4.0 inch 5. Torx screws (2) 6. Hook and loop fastener, 6.0 inch 7. Anchor tab (install first) Figure 1. Saddlebag Lid Cover Installation 2. Wash the entire saddlebag lid, inside and out, with warm, soapy water. Rinse and dry thoroughly. 3. Use the alcohol prep pad provided in the kit to further clean the inside of the lid in the areas where the hook and loop strips will be attached. NOTE The Saddlebag Lid Covers are side-specific. A Bar-and-Shield logo is stitched into the rear face of each cover. NOTE DO NOT fasten the Saddlebag Lid Cover tabs to the hook and loop strips until the adhesive has cured for 24 hours. 4. Place the correct Saddlebag Lid Cover (1) over the saddlebag lid in its proper position. Bring the cover tabs over the edge of the lid to serve as a guide in positioning the hook and loop strips on the inside of the lid. Remove the protective backing from one hook and loop strip at a time. Use the corresponding tab on the cover only as a positioning guide, then fold it back out of the

HARLEY DAVIDSON TOUR-PAK WALL ORGANIZER INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 11-02-2011

download
This kit fits 1997 and later models equipped with King Tour- Paks INSTALLATION NOTE Maximum Wall Organizer weight capacity is 3 pounds (1.4 Kg) evenly distributed. Do not exceed tour-pak weight capacity. Too much weight can cause loss of control, which could result in death or serious injury. (00401b) Tour-Paks With Molded Liner 1. Remove the two nuts that hold the pouch and liner in the Tour-Pak. Remove pouch and liner and carefully wash the inside of the Tour-Pak with warm, soapy water. Rinse and dry thoroughly. 2. Use the alcohol prep pad in the kit to thoroughly clean the interior surface of the Tour-Pak sides where fastener strips will be attached. Make sure any residue is removed, then allow Tour-Pak to dry completely. Make sure the surface is free of condensed moisture. NOTES The hook and loop fastener strips and organizer must be installed below the edge of Tour-Pak base to avoid interference with top gasket and lock. The ideal temperature range for applying the fastener strip is 70-100° F (21-38° C). Minimum application temperature is 50° F (10° C). If you attempt to apply the tape below these temperatures, the adhesive will become too firm to adhere readily. 3. See Figure 1 and Figure 2. Remove the hook and loop fastener strips from the hinged hook and loop strips. Remove the paper backing and firmly press the fastener strips into the locations (1) shown in Figure 2. The fastener strips should be located approximately 1/8 in. (3 mm) below the edge of the Tour-Pak base. 4. See Figure 1. Bend the hinged hook and loop strips (3) into shape as shown. Attach the hinged strips onto the fastener strips (2) installed in Step 3. NOTE The Tour-pak Wall Organizer installs in place of the pouch removed in Step 1, therefore the pouch will not be re-installed. 5. Reinstall the liner removed in Step 1. The hinged strips (3) will go over the top of the liner (4) as shown in Figure 1. 6. See Figure 1. Attach the organizer (5) to the hinged strips (3). Adjust the organizer’s lock cut out so that it is centered around the lock, and press the hook side of the hook and loop strips on the bottom of the organizer into place on the liner. The hook side will attach to the liner. NOTE 2006 and later Tour-Paks equipped with Passenger Backrest will have two acorn nuts at the front of the base. Remove and discard the 8 in. (200 mm) long hook and loop hinged fastener strip from the center panel. In one of the organizer pockets there will be 4 in. (100 mm) and 1-1/2 in. (38 mm) hook and loop hinged fastener strips. Install the hinged strips on the organizer center panel as shown in Figure 3. 7. Check to make sure the Tour-Pak lid closes over the organizer and the lock works without interference. Adjust as necessary. 8. Allow tape to cure (“wet-out”) for a minimum of 48 hours at 70° F (21° C) (allow extra time if temperature is below 70°). Do not place items in the Wall Organizer while adhesive is curing

HARLEY DAVIDSON CRUISER II SADDLEBAG MOUNTING INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 02-12-2010

download
a. Adjust the mounting yoke by first removing the lacing system that secures the two yoke halves. b. Move the two yoke halves inward or outward until the saddlebags ride as high as possible on both sides of the motorcycle. When properly adjusted, both bags will hang parallel to one another. c. Utilizing the lacing pattern shown in both images (A ) and (B ) , reinstall and fasten the lacing system. The lacing must pass through a minimum of four sets of adjustment holes on the mounting yoke. WARNING: Saddlebags must never contact the rear wheel, drive train or exhaust. A minimum clearance of two inches, with the suspension compressed, is necessary at all times. CAUTION: Tour Master saddlebags do not fit under the seat of all motorcycles. Please check your motorcycle’s factory supplied owners manual for under saddle mounting compatibility and proper seat removal and installation. II. MOUNTING STRAP INSTALLATION: a. With the yoke properly adjusted, attach each of the four mounting straps (C ) and ( D ) to a rigid portion of the frame or rear rack assembly. b. Connect the quick-release buckles and pull the adjustment straps tight. c. Secure excess strap tether with the integrated hook and loop fastener

SHOCK CUTAWAY SADDLEBAG INSTALLATION INSTRUCTIONS

0

Filed Under (Tips and Review) by admin on 10-11-2010

download
1. Saddlemen saddlebags mount over the back of the seat or rear fender of most motorcycles. When properly installed there will be one saddlebag on each side of the motorcycle with the split yoke resting on the fender or the seat. Both saddlebags must be securely mounted and tied down in a manner that does not interfere with any part of the motorcycle’s operation. Be certain the saddlebags or their mountings do not contact brake components, turn signals, taillight, brake light, suspension, swingarm, or drivetrain. These Shock Cutaway saddlebags have been designed to fit over your bike’s shock absorbers (see Fig. A), which allow for larger bags on bikes otherwise limited by shock and turn signal location. 2. We highly recommend that your bike be equipped with Saddlemen’s S4 saddlebag supports (see Fig. B) or equivalent. Saddlemen also offers Quick Disconnect rigid-mounting hardware kits for most bikes, that allow easy on, easy off bag installation and eliminate the yoke. For more information, see your dealer or contact Saddlemen at 310- 638-1222. 3. Your saddlebags must be at least two inches away from any exhaust pipe while the motorcycle is stationary or moving. You can adjust the split yoke to change the height of the bag on the motorcycle by adjusting the position of the hook and loop fastening system (Fig. C). Adjust the split yoke shorter to raise the height of the saddlebags, and longer to lower the height of the saddlebags. The split yoke can also be reversed by unbolting each yoke half from each saddlebag, and reversing the yoke’s position on your bike. This allows for the offset in the yoke to be positioned either forward or backwards providing clearance for the motorcycle’s components (Fig. D). 4. In addition to the hook and loop fastener, the bags rely on a nylon safety strap system to ensure proper and secure installation. This strap must be used, and tightened snugly. Assure that the strap’s short end with D-rings is pushed through the slot in the split yoke and resting on the topside it. Once the split yoke is set to the proper position, run the long safety strap over the top of the split yoke and secure it to the D-rings (see Fig E and F), and tighten it. 5. Once you’ve placed the saddlebags on your bike and have them adjusted properly, use the straps located on the bottom of each saddlebag (see Fig. E and G) to connect the saddlebag to the saddlebag support (if you are using Saddlemen’s S4 Saddlebag bracket refer to the instructions shipped with it). These lower straps adjust in length to assure a tight fit. Wrap them around the saddlebag support, snap the buckle halves together, and adjust the length of the strap assuring the strap is tight and supporting some of the saddlebags’ weight. Repeat this step on the other saddlebag.