Kawasaki ZX-14 TITANIUM SIDEWINDER EXHAUST Installation Instructions

0

Filed Under (Kawasaki) by admin on 30-04-2012

download
STEP 2: PRE-ASSEMBLE HEADERS, COLLECTOR, AND MID-PIPE TO INSURE PROPER FIT BETWEEN ALL PARTS: Brock’s Performance pre-assembles the exhaust system before it is shipped to your door. We ask you to this to insure there were no shipping damages incurred before you start disassembling your bike. A lot of our customers use WD-40 applied to the joints to ease assembly, adjustment, and/or disassembly. STEP 3: REMOVE ZX-14 RIGHT AND LEFT DASHBOARDS : The right and left dashboards are held in place by three fasteners (Figure 4) which are removed with a No. 4 hex head wrench. Note that all dashboard and fairing fasteners have thin plastic washers located between the fastener head and the plastic body work. Be careful to save the plastic washers. To avoid losing fasteners and washers it is recommended that the installer place them in a container once they are removed. STEP 4: REMOVE ZX-14 LOWER FAIRING : The lower fairing consists of separate right and left side panels, both of which should be removed. The locations of the bolts and plastic push pins holding the fairing in place are illustrated in Figure 5. Details are provided below. • The plastic push pins is located in the front of the fairing (3) , aft of the front tire, and holds the left and right panels together. Remove the plastic push pins using a thin blade screw driver to lift the rivet head. Then pull the rivet from the bodywork. This will release the right panel from the left panel. • Remove the lower fairing fasteners & washers (1 & 2) on the right fairing panel with a No. 5 hex head wrench. • Remove the upper fairing fasteners & washers (4, 5, & 6) on the right fairing panel with a No. 4 hex head wrench. • Note that the top of the fairing incorporates slots into which hooks at the bottom of the mid fairing (red bodywork) fit. These hooks are shown in Figure 8. Pull the bottom of the lower fairing panel away from the bike and then downward to clear the hooks from the slots. The right side lower fairing should now separate easily from the mid-fairing. • Repeat for the left side lower fairing

YAMAHA YBR250 OWNER'S MANUAL

0

Filed Under (Yamaha) by admin on 15-12-2010

download
Always adjust both shock absorber assemblies equally, otherwise poor handling and loss of stability may result. To increase the spring preload and thereby harden the suspension, turn the adjusting ring on each shock absorber assembly in direction (a). To decrease the spring preload and thereby soften the suspension, turn the adjusting ring on each shock absorber assembly in direction (b). Align the appropriate notch in the adjusting ring with the position indicator on the shock absorber. Spring preload setting: Minimum (soft): 1 Standard: 3 Maximum (hard): 5 EAU36700 Luggage strap holders 1. Luggage strap holder There are four luggage strap holders on the bottom of the seat. To use the strap holders, remove the seat, unhook the straps from the hooks, and then install the seat with the straps hanging out from under the seat. (See page 3-9.) EAU15301 Sidestand The sidestand is located on the left side of the frame. Raise the sidestand or lower it with your foot while holding the motorcycle upright. The built-in sidestand switch is part of the ignition circuit cut-off system, which cuts the ignition in certain situations. (See further down for an explanation of the ignition circuit cut-off system.) EWA10240 The vehicle must not be ridden with the sidestand down, or if the sidestand cannot be properly moved up (or does not stay up), otherwise the sidestand could contact the ground and distract the operator, resulting in a possible loss of control. Yamaha’s ignition circuit cut-off system has been designed to assist the operator in fulfilling the responsibility of raising the sidestand before starting off. Therefore, check this system regularly as described

1,000 POUND CAPACITY MOTORCYCLE / ATV LIFT RML-600 INSTALLATION AND OPERATION MANUAL

0

Filed Under (Tips and Review) by admin on 25-11-2010

download
6 RML-600 Instructions 1. Center load on table – 1000 lb. maximum. 2. Connect to 100 PSI maximum shop air. 3. Keep safety bar in position at all times – except when lowering. 4. Keep hands and tools from under carriage. 5. Do not mount table when in elevated position. 6. Do not ride vehicle onto lift. 7. Lift must be in the lowered position when moving. 8. Only trained persons should operate Air Lift. 9. The working area should be sufficiently lit. 10. Foot controller should be at least 3 feet away from Air Lift during raising and lowering operation. 11. Lift is recommended for indoor use only. nstallation Instructions The Cycle Vise mounts directly onto the RML-600. Align two inside holes of the fixed clamp over the existing vise hole pattern as shown. Align the moveable clamp with the locating corner hole. CYCLE VISE
8 1. Insert pipes from extension panel package through holes in lift table. 2. Mount panels on ends of pipe on each side of table. With ramp hole to outside. 3. Insert M8 BOLTprovided through holes in each end of pipe. 4. Secure ramp extensions to ramp with bolts provided. Make sure ramp hooks are positioned on the outside. 5. Stabilization bar directions – Unscrew cap from one of the ends of the stabilization pipe. 6. Insert bolt in drilled out hole and tighten with nut. Slide pipe through the stationary square tubing on the lift legs. Insert the other bolt, tighten down with nut. Put on the other cap and tighten. Installation Instructions (Optional) 12″ Side Extensions
9 POSITION THE 13″ EXTENSION OVER THE EXISTING TABLE AS SHOWN AND ATTACH WITH FOUR M8 CAPSCREWS, NUTS AND LOCK WASHERS PROVIDED. EYE BOLTS ARE ALSO PROVIDED WITH THE EXTENSION KITAND MAYBE INSTALLED AS SHOWN USING M8 HEX NUTS AND LOCKWASHERS