HARLEY DAVIDSON FX SOFTAIL FRONT LOWERING SUSPENSION KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 04-04-2011

download
REMOVAL 1. Place suitable blocking under frame to raise front wheel several inches off the floor. For best results, use a hydraulic center stand on a level surface. 2. Refer to the appropriate Service Manual and remove the front forks. 3. Move forks to bench area. Place suitable drain pan on floor beneath a vise. INSTALLATION Fork Disassembly 1. See Figure 6. Remove nuts (T), lockwashers (S), flat washers (R) and axle cap from studs at end of fork slider. 2. See Figure 1. Obtain FORK TUBE HOLDER (HD-41177) and proceed as follows: a. Clamp end of tool in vise (1) in a horizontal position with plastic knobs facing toward you. b. With the fork cap bolt topside, clamp fork tube between rubber pads (2) on inboard side of tool. Tighten knobs (3) until fork tube is securely held. NOTE Refer to Figure 6 for Steps 3-17. 3. Remove fork cap bolt (A) and spacer (O) from fork tube plug (B). Remove quad ring seal (D). Save bolt and spacer but discard quad ring seal. 4. Using wrench flat, slowly unthread fork tube plug (B) from fork tube (G). Be aware that fork tube plug is under spring -J03923 1 of 4 pressure, so have a firm grasp on plug as the last thread is turned. 5. Remove fork spring (1) from fork tube. 6. Remove fork assembly from fork tube holder. 7. Turning fork upside down, drain fork oil into drain pan. For best results, slowly pump fork tube and slider at least 10 times. 8. Install fork spring back into fork tube. 9. Place a shop rag on the floor, and turning fork assembly upside down, press end of spring against rag. While compressing spring to prevent rotation of damper tube, remove screw and washer (Q) from end of fork slider. Use air impact wrench for best results. 10. Remove and discard fork spring (1). 11. Remove dust cover (E). 12. Using pick tool, remove retaining clip (H) between fork slider and fork tube. 13. Remove fork tube (G) from fork slider. Slide fork tube gently in a slide hammer motion against the slider to remove the seals and bushing from slider. 14. Slide fork oil seal (I), slider spacer (J) and slider bushing (K) off end of fork tube (G). NOTE The lower stop (L) may come out with the damper tube or remain in the slider tube. Ensure that the lower stop is removed from the slider tube. 15. Remove the lower stop (L). 16. Remove damper tube (2) from fork tube. 17. Remove rebound spring (F) from damper tube. 18. Repeat Steps 1-17 for the opposite side fork assembly. Fork Assembly

HARLEY DAVIDSON VRSC REAR AXLE COVERS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 17-03-2011

download
This kit fits 2002 and later VRSC model motorcycles. Kit Contents There are no Service Parts available with this kit. INSTALLATION 1. Using a suitable lift, support the vehicle beneath the frame until the rear tire is just slightly off the ground. 2. See Figure 1. Remove the right side upper shock mounting bolt (2) and spacer (4). Retain the shock mounting nut (not shown) which passes through the fender support and side rail assembly. 3. Pivot the shock towards the vertical position. 4. Remove the left side lower shock mounting bolt (1) and washer (5). 5. Pivot the shock towards the horizontal position. 6. Insure that the shocks are clear of all components and carefully lower the vehicle to provide access to the right side lower shock bolt. 7. Support the right shock and remove the lower shock mounting bolt (1), washer (5) and nut (6). 8. Position the right side cover provided in the kit over the swingarm 9. Reposition the right side shock and re-install the lower shock mounting bolt (1) and washer (5) by inserting through the shock, cover and swingarm. Thread into nut (6) and tighten to 41-68 Nm (30-50 ft-lbs)

HARLEY DAVIDSON TOURING FRONT LOWERING KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 02-03-2011

download
REMOVAL 1. Place suitable blocking under frame to raise front wheel several inches off the floor. For best results, use a hydraulic center stand on a level surface. 2. Refer to the appropriate Service Manual and remove the front forks. 3. Move forks to bench area. Place suitable drain pan on floor beneath a vise. INSTALLATION Fork Disassembly 1. See Figure 6. Remove nuts (U), lockwashers (T), flat washers (S) and axle holder (R) from studs at end of fork slider. 2. See Figure 1. Obtain FORK TUBE HOLDER (HD-41177) and proceed as follows: a. Clamp end of tool in vise (1) in a horizontal position with plastic knobs facing toward you. b. With the fork cap bolt topside, clamp fork tube between rubber pads (2) on inboard side of tool. Tighten knobs (3) until fork tube is securely held. NOTE Refer to Figure 6 for Steps 3-17. 3. Remove fork cap bolt (A) from fork tube plug. Remove quad ring seal. Save bolt but discard quad ring seal. 4. Using wrench flat, slowly unthread fork tube plug (B) from fork tube (G). Be aware that fork tube plug is under spring pressure, so have a firm grasp on plug as the last thread is turned. 5. Remove fork spring (1) from fork tube. 6. Remove fork assembly from fork tube holder. 7. Turning fork upside down, drain fork oil into drain pan. For best results, slowly pump fork tube and slider at least 10 times. 8. Install fork spring back into fork tube. 9. Place a shop rag on the floor, and turning fork assembly upside down, press end of spring against rag. While compressing spring to prevent rotation of damper tube, remove screw and washer (Q) from end of fork slider. Use air impact wrench for best results. 10. Remove and discard fork spring. 11. Remove and save blow valve (E). 12. Remove damper tube (2). 13. Remove rebound spring (F) from damper tube. 14. Using pick tool, remove retaining clip (H) between fork slider and fork tube. 15. Remove fork tube (G) from fork slider. Slide fork tube gently in a slide hammer motion against the slider to remove the seals and bushing from slider. 16. Slide fork oil seal (I), slider spacer (J) and slider bushing (K) off end of fork tube (G). 17. Remove the lower stop (L). Fork Assembly NOTE Refer to Figure 6 for the following procedure. 1. Obtain new Damper Tube (2) from kit and install rebound spring (F) over the lower end. 2. With the wear ring topside, slide new damper tube into fork tube, so that tube end drops through hole at bottom of fork tube (G). Install lower stop (L) on the lower end of damper tube. 3. Install fork slider (O or N) in fork tube holder. Slide fork tube into fork slider. 4. If necessary, obtain new slider bushing (K) (45940-84, not included). Coat slider bushing ID with clean fork oil. Slide slider bushing (K) down fork tube. 5. Slide slider spacer (J) down fork tube until it contacts slider bushing. 6. Obtain new fork oil seal (I) (45875-84A, not included). Coat fork oil seal ID with clean fork oil. With the lip garter spring side facing down (toward the fork slider), slide oil seal down fork tube until it contacts slider spacer title_tag=

HAR:EY DAVIDSON FLHR/C/S (Road King) FRONT END LOWERING KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 01-03-2011

download
Removal (Left and Right Forks) 1. Place suitable blocking under frame to raise front wheel several inches off the floor. For best results, use a hydraulic center stand on a level surface. 2. Refer to Touring Model Service Manual and remove front wheel, fender and brakes. 3. Refer to Touring Model Service Manual and remove headlamp nacelle. 4. Loosen fork cap bolt from fork tube plug at top of fork tube, but do not remove. 5. See Figure 1. Standing at front of vehicle, loosen pinch bolt (with lockwasher) on right side of lower fork bracket, but do not remove. 6. Spray glass cleaner on fork tube above the rubber fork stop. After lubricating surfaces, move fork stop up fork tube until it contacts bottom of upper fork bracket. 7. Holding fork slider to prevent fork from dropping, remove fork cap bolt from fork tube plug. Slide fork tube down and out of upper fork bracket, fork stop, lower fork bracket and slider cover. 1 WARNING 1 WARNING 1 WARNING 1 of 5 ® Kit Number 54614-05 Figure 1. Loosen Pinch Bolt on Lower Fork Bracket i04808 1 Fork cap bolt 2 Fork stop 3 Pinch bolt 8. Thread fork cap bolt back into fork tube plug to prevent loss of oil while handling. 9. Move forks to bench area. Place suitable drain pan on floor beneath vise. 10. Repeat Steps 2-6 to remove left fork. Left And Right Fork-Disassembly 1. Remove nuts, lockwashers, flat washers and axle holder from studs at end of fork slider. 2. See Figure 2. Obtain FORK TUBE HOLDER (Part Number HD-41177) and proceed as follows: a. Clamp end of tool in vise in a horizontal position with plastic knobs facing toward you. b. See Figure 3. With the fork cap bolt topside, clamp fork tube between rubber pads on inboard side of tool. Tighten knobs until fork tube is securely held. 3. Remove fork cap bolt from fork tube plug. Remove quad ring seal. Save bolt but discard quad ring seal. 4. Using wrench flat, slowly unthread fork tube plug from fork tube. Be aware that fork tube plug is under spring pressure, so have a firm grasp on plug as the last thread is turned. 5. Remove fork spring from fork tube. 6. Remove fork assembly from fork tube holder. 7. Turning fork upside down, drain fork oil into drain pan. For best results, slowly pump fork tube and slider at least 10 times. 8. Install fork spring back into fork tube. 9. Place a shop rag on the floor, and turning fork assembly upside down, press end of spring against rag. While compressing spring to prevent rotation of damper tube, remove 6mm screw from end of fork slider. Use air impact wrench for best results. 10. Remove and discard fork spring. 11. Remove and discard damper tube. 12. Remove wear ring and rebound spring. Discard rebound spring. Do not expand or stretch retaining clip to remove from fork tube or clip may become bent or distorted. 13. Using pick tool, remove retaining clip between fork slider and fork tube. 14. Remove fork tube from fork slider. NOTE To overcome any resistance, use the fork tube as a slide hammer, that is, first push fork tube into fork slider and then pull it outward with a moderate amount of force. Repeat this sequence until fork tube separates from fork slider. 15. Slide fork oil seal, slider spacer and slider bushing off end of fork tube. Discard fork oil seal and slider bushing. 16. Remove the lower stop. Right and Left Fork-Assembly Exercise caution to avoid scratching or nicking fork tube. Damaging tube can result in fork oil leaks after assembly. 1. See Service Parts Illustration. Obtain new Damper Tube (Item 7, Part Number 46532-04) from kit. Obtain new Rebound Spring (Item 8, Part Number 46273-02) from kit and install on opposite end. Install wear ring removed in step 12. 2. With the wear ring topside, slide new damper tube into fork tube, so that tube end drops through hole at bottom of fork tube. Install lower stop at end of damper tube. 3. Install fork slider in fork tube holder. Slide fork tube into fork slider. 4. If necessary, obtain new slider bushing (14) (Part Number 45940-84, not included). Coat slider bushing ID with clean fork oil. Slide slider bushing down fork tube. 5. Slide slider spacer down fork tube until it contacts slider bushing.

Incoming search terms:

HARLEY DAVIDSON BRAIDED STAINLESS STEEL FUEL CROSSOVER LINE KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 11-02-2011

download
INSTALLATION, CARBURETED MODELS Models WITH maxi-fuse: To prevent accidental vehicle start-up, which could cause death or serious injury, remove maxi-fuse before proceeding. (00251a) 1. Refer to the Service Manual and follow the instructions given to remove the maxi-fuse. Models WITHOUT maxi-fuse: To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) 1. Refer to the Service Manual and follow the instructions given to remove the seat and disconnect the negative (black) battery cable from the negative (-) battery terminal. Retain all seat mounting hardware. ALL carbureted models When servicing the fuel system, do not smoke or allow open flame or sparks in the vicinity. Gasoline is extremely flammable and highly explosive, which could result in death or serious injury. (00330a) 2. See FUEL SUPPLY VALVE FILTER: CARBURETED in the Service Manual. a. Turn the fuel supply valve to the OFF (horizontal) position. b. Follow the instructions to disconnect the fuel hose from the fuel supply valve outlet nipple. Drain the fuel from the fuel tank into an adequately sized, approved gasoline container using a vacuum pump (Plastic Mity-Vac hand pump or equivalent). c. Re-install the fuel hose to the fuel supply valve with a new fuel hose clamp (Part Number 10014), purchased separately. d. Proceed to Step

HARLEY DAVIDSON SADDLEBAG WALL ORGANIZER KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 03-02-2011

download
INSTALLATION Do not exceed saddlebag weight capacity. Put equal weight in each bag. Too much weight in saddlebags can cause loss of control, which could result in death or serious injury. (00383a) NOTE Maximum load capacity of the wall organizer is 2.5 lbs (1.1 Kg). The combined load of wall organizer and saddlebag must not exceed 15 lbs (6.8 Kg). Saddlebag Without Liners 1. See Figure 1. Open saddlebag. NOTE On some HDI motorcycles, the bail wire has been removed from the quick release stud. In these cases, turn the stud by engaging the slotted end with a large screwdriver. 2. See Figure 2. Grasp bail wire (1) inside saddlebag and rotate front bail head stud (2) a full 1/4 turn in a counterclockwise direction. Remove front bail head stud (2) and flat washer (3). Discard washer but save stud for kit installation. 3. See Figure 3. Place flat washer (1) from kit on front bail head stud. 2 1 2 is03120 1. Anchor bracket (2) 2. Bail head stud and flat washer (2) Figure 1. Open/Close Saddlebag 1 2 3 5 4 6 7 is03114 1. Bail wire 2. Bail head stud 3. Flat washer (stock) 4. Spring plate 5. Wire form 6. Front bracket 7. Rear bracket Figure 2. Saddlebag Quick-Release Fasteners 4. With groove at end of stud held in a horizontal position, insert front bail head stud (2) and flat washer (1) through hole in wall organizer (3), saddlebag, and mounting bracket. When groove engages wire form of spring plate

BMW R 1200 C And R 850 C REPAIR MANUAL

0

Filed Under (BMW) by admin on 22-11-2010

download
BMW Inspection 1000 km/600 miles I -BMW Service II -BMW Inspection III -BMW Annual Service IV Reading out MoDiTeC fault memory (Inspections I, II, III and IV) • Remove the left air cleaner trim panel. • Connect MoDiTeC to diagnostic plug. • Read out the fault memory. • Perform any repair work indicated. Checking throttle cable play, adjusting if necessary (Inspections I and III) • Check throttle cable for free movement and freedom from abrasion or kinking; renew if neces- sary. • With the steering turned to various angles, open the throttle twistgrip fully and allow it to close again. • When released, the twistgrip must return to the closed position by itself. • Pull back the protective cap. • Preset throttle cable play with the engine cold to 1.5 mm (0.06 in). • Warm the engine up to its regular operating tem- perature. • Adjust throttle cable play to 0.5mm (0.02 in) Changing engine oil, renew oil filter element (Inspections I, II, III and IV) L Note: If the motorcycle is ridden only for short distances or outside temperatures are below 0°C (32°F): change the oil and renew the oil filter element every 3 months, but at least every 3 000 km (1 800 miles). • Change the oil while it is at regular operating temperature. • Remove screw plug. • Unscrew oil drain plug and drain off oil. • Fit new seal and screw in drain plug. • Use oil filter wrench, BMW No. 11 4 650 , to unscrew and remove the oil filter. • Coat sealing ring on new oil filter element with oil and screw in. • Add oil. • Insert and tighten the screw plug. • Check engine oil level with the motorcycle in a horizontal position; use the auxiliary stand, BMW No. 001550 . e Caution: Never add engine oil above the MAX mark. X Tightening torque: Oil filter………………………………………………… 11 Nm Oil drain plug………………………………………… 32 Nm Fill quantity for engine: With oil filter change.. 3.75 l (6.6 Imp. pints/3.96 US quarts) Without oil filter change.. 3.50 l (6.2 Imp. pints/3.69 US quarts) Oil volume between MIN and MAX marks……0.50 l (0.88 Imp. pint/0.52 US quart) Engine oil grade: Brand-name HD oil for four-stroke spark-ignition engine, API classifications SE, SF, SG; combination with CC or CD specification

Incoming search terms: